/* SPDX-License-Identifier: GPL-2.0+ */ /* * Copyright 2014 Freescale Semiconductor, Inc. * Copyright 2020-2021 NXP */ /* * T2080 RDB/PCIe board configuration file */ #ifndef __T2080RDB_H #define __T2080RDB_H #include #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ /* High Level Configuration Options */ #define CFG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS #ifdef CONFIG_RAMBOOT_PBL #define RESET_VECTOR_OFFSET 0x27FFC #define BOOT_PAGE_OFFSET 0x27000 #ifdef CONFIG_MTD_RAW_NAND #define CFG_SYS_NAND_U_BOOT_SIZE (768 << 10) #define CFG_SYS_NAND_U_BOOT_DST 0x00200000 #define CFG_SYS_NAND_U_BOOT_START 0x00200000 #endif #ifdef CONFIG_SPIFLASH #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC #define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10) #define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000) #define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000) #define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10) #endif #ifdef CONFIG_SDCARD #define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC #define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10) #define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000) #define CONFIG_SYS_MMC_U_BOOT_START (0x00200000) #define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10) #endif #endif /* CONFIG_RAMBOOT_PBL */ #define CONFIG_SRIO_PCIE_BOOT_MASTER #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE /* Set 1M boot space */ #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_TEXT_BASE & 0xfff00000) #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc #endif #ifndef CONFIG_RESET_VECTOR_ADDRESS #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc #endif /* * These can be toggled for performance analysis, otherwise use default. */ #ifdef CONFIG_DDR_ECC #define CONFIG_MEM_INIT_VALUE 0xdeadbeef #endif /* * Config the L3 Cache as L3 SRAM */ #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 #define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) #define CONFIG_SYS_DCSRBAR 0xf0000000 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull /* * DDR Setup */ #define CONFIG_VERY_BIG_RAM #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ #define SPD_EEPROM_ADDRESS1 0x51 #define SPD_EEPROM_ADDRESS2 0x52 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 #define CTRL_INTLV_PREFERED cacheline /* * IFC Definitions */ #define CONFIG_SYS_FLASH_BASE 0xe8000000 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ CSPR_PORT_SIZE_16 | \ CSPR_MSEL_NOR | \ CSPR_V) #define CFG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024) /* NOR Flash Timing Params */ #define CFG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80 #define CFG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \ FTIM0_NOR_TEADC(0x5) | \ FTIM0_NOR_TEAHC(0x5)) #define CFG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ FTIM1_NOR_TRAD_NOR(0x1A) |\ FTIM1_NOR_TSEQRAD_NOR(0x13)) #define CFG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \ FTIM2_NOR_TCH(0x4) | \ FTIM2_NOR_TWPH(0x0E) | \ FTIM2_NOR_TWP(0x1c)) #define CFG_SYS_NOR_FTIM3 0x0 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS } /* CPLD on IFC */ #define CONFIG_SYS_CPLD_BASE 0xffdf0000 #define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE) #define CONFIG_SYS_CSPR2_EXT (0xf) #define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \ | CSPR_PORT_SIZE_8 \ | CSPR_MSEL_GPCM \ | CSPR_V) #define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024) #define CONFIG_SYS_CSOR2 0x0 /* CPLD Timing parameters for IFC CS2 */ #define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ FTIM0_GPCM_TEADC(0x0e) | \ FTIM0_GPCM_TEAHC(0x0e)) #define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ FTIM1_GPCM_TRAD(0x1f)) #define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ FTIM2_GPCM_TCH(0x8) | \ FTIM2_GPCM_TWP(0x1f)) #define CONFIG_SYS_CS2_FTIM3 0x0 /* NAND Flash on IFC */ #define CFG_SYS_NAND_BASE 0xff800000 #define CFG_SYS_NAND_BASE_PHYS (0xf00000000ull | CFG_SYS_NAND_BASE) #define CFG_SYS_NAND_CSPR_EXT (0xf) #define CFG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CFG_SYS_NAND_BASE_PHYS) \ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ | CSPR_MSEL_NAND /* MSEL = NAND */ \ | CSPR_V) #define CFG_SYS_NAND_AMASK IFC_AMASK(64*1024) #define CFG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ | CSOR_NAND_PGS_2K /* Page Size = 2K */\ | CSOR_NAND_SPRZ_64 /* Spare size = 64 */\ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ /* ONFI NAND Flash mode0 Timing Params */ #define CFG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ FTIM0_NAND_TWP(0x18) | \ FTIM0_NAND_TWCHT(0x07) | \ FTIM0_NAND_TWH(0x0a)) #define CFG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ FTIM1_NAND_TWBE(0x39) | \ FTIM1_NAND_TRR(0x0e) | \ FTIM1_NAND_TRP(0x18)) #define CFG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ FTIM2_NAND_TREH(0x0a) | \ FTIM2_NAND_TWHRE(0x1e)) #define CFG_SYS_NAND_FTIM3 0x0 #define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE } #if defined(CONFIG_MTD_RAW_NAND) #define CONFIG_SYS_CSPR0_EXT CFG_SYS_NAND_CSPR_EXT #define CONFIG_SYS_CSPR0 CFG_SYS_NAND_CSPR #define CONFIG_SYS_AMASK0 CFG_SYS_NAND_AMASK #define CONFIG_SYS_CSOR0 CFG_SYS_NAND_CSOR #define CONFIG_SYS_CS0_FTIM0 CFG_SYS_NAND_FTIM0 #define CONFIG_SYS_CS0_FTIM1 CFG_SYS_NAND_FTIM1 #define CONFIG_SYS_CS0_FTIM2 CFG_SYS_NAND_FTIM2 #define CONFIG_SYS_CS0_FTIM3 CFG_SYS_NAND_FTIM3 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR #define CONFIG_SYS_AMASK1 CFG_SYS_NOR_AMASK #define CONFIG_SYS_CSOR1 CFG_SYS_NOR_CSOR #define CONFIG_SYS_CS1_FTIM0 CFG_SYS_NOR_FTIM0 #define CONFIG_SYS_CS1_FTIM1 CFG_SYS_NOR_FTIM1 #define CONFIG_SYS_CS1_FTIM2 CFG_SYS_NOR_FTIM2 #define CONFIG_SYS_CS1_FTIM3 CFG_SYS_NOR_FTIM3 #else #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR #define CONFIG_SYS_AMASK0 CFG_SYS_NOR_AMASK #define CONFIG_SYS_CSOR0 CFG_SYS_NOR_CSOR #define CONFIG_SYS_CS0_FTIM0 CFG_SYS_NOR_FTIM0 #define CONFIG_SYS_CS0_FTIM1 CFG_SYS_NOR_FTIM1 #define CONFIG_SYS_CS0_FTIM2 CFG_SYS_NOR_FTIM2 #define CONFIG_SYS_CS0_FTIM3 CFG_SYS_NOR_FTIM3 #define CONFIG_SYS_CSPR1_EXT CFG_SYS_NAND_CSPR_EXT #define CONFIG_SYS_CSPR1 CFG_SYS_NAND_CSPR #define CONFIG_SYS_AMASK1 CFG_SYS_NAND_AMASK #define CONFIG_SYS_CSOR1 CFG_SYS_NAND_CSOR #define CONFIG_SYS_CS1_FTIM0 CFG_SYS_NAND_FTIM0 #define CONFIG_SYS_CS1_FTIM1 CFG_SYS_NAND_FTIM1 #define CONFIG_SYS_CS1_FTIM2 CFG_SYS_NAND_FTIM2 #define CONFIG_SYS_CS1_FTIM3 CFG_SYS_NAND_FTIM3 #endif #define CONFIG_HWCONFIG /* define to use L1 as initial stack */ #define CONFIG_L1_INIT_RAM #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 /* The assembler doesn't like typecast */ #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 #define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) /* * Serial Port */ #define CFG_SYS_NS16550_CLK (get_bus_freq(0)/2) #define CONFIG_SYS_BAUDRATE_TABLE \ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} #define CFG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) #define CFG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) #define CFG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) #define CFG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) /* * I2C */ #define I2C_MUX_PCA_ADDR_PRI 0x77 /* I2C bus multiplexer,primary */ #define I2C_MUX_PCA_ADDR_SEC1 0x75 /* I2C bus multiplexer,secondary 1 */ #define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */ #define I2C_MUX_CH_DEFAULT 0x8 #define I2C_MUX_CH_VOL_MONITOR 0xa /* The lowest and highest voltage allowed for T208xRDB */ #define VDD_MV_MIN 819 #define VDD_MV_MAX 1212 /* * RapidIO */ #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ /* * for slave u-boot IMAGE instored in master memory space, * PHYS must be aligned based on the SIZE */ #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull /* * for slave UCODE and ENV instored in master memory space, * PHYS must be aligned based on the SIZE */ #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ /* slave core release by master*/ #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ /* * SRIO_PCIE_BOOT - SLAVE */ #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) #endif /* * eSPI - Enhanced SPI */ /* * General PCI * Memory space is mapped 1-1, but I/O space must start from 0. */ /* controller 1, direct to uli, tgtid 3, Base address 20000 */ #define CFG_SYS_PCIE1_MEM_VIRT 0x80000000 #define CFG_SYS_PCIE1_MEM_PHYS 0xc00000000ull #define CFG_SYS_PCIE1_IO_VIRT 0xf8000000 #define CFG_SYS_PCIE1_IO_PHYS 0xff8000000ull /* controller 2, Slot 2, tgtid 2, Base address 201000 */ #define CFG_SYS_PCIE2_MEM_VIRT 0xa0000000 #define CFG_SYS_PCIE2_MEM_PHYS 0xc20000000ull #define CFG_SYS_PCIE2_IO_VIRT 0xf8010000 #define CFG_SYS_PCIE2_IO_PHYS 0xff8010000ull /* controller 3, Slot 1, tgtid 1, Base address 202000 */ #define CFG_SYS_PCIE3_MEM_VIRT 0xb0000000 #define CFG_SYS_PCIE3_MEM_PHYS 0xc30000000ull /* controller 4, Base address 203000 */ #define CFG_SYS_PCIE4_MEM_VIRT 0xc0000000 #define CFG_SYS_PCIE4_MEM_PHYS 0xc40000000ull /* Qman/Bman */ #ifndef CONFIG_NOBQFMAN #define CONFIG_SYS_BMAN_NUM_PORTALS 18 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ CONFIG_SYS_BMAN_CENA_SIZE) #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 #define CONFIG_SYS_QMAN_NUM_PORTALS 18 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ CONFIG_SYS_QMAN_CENA_SIZE) #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 #define CONFIG_SYS_DPAA_FMAN #define CONFIG_SYS_DPAA_PME #define CONFIG_SYS_PMAN #define CONFIG_SYS_DPAA_DCE #define CONFIG_SYS_DPAA_RMAN /* RMan */ #endif /* CONFIG_NOBQFMAN */ #ifdef CONFIG_SYS_DPAA_FMAN #define RGMII_PHY1_ADDR 0x01 /* RealTek RTL8211E */ #define RGMII_PHY2_ADDR 0x02 #define CORTINA_PHY_ADDR1 0x0c /* Cortina CS4315 */ #define CORTINA_PHY_ADDR2 0x0d /* Aquantia AQ1202 10G Base-T used by board revisions up to C */ #define FM1_10GEC3_PHY_ADDR 0x00 #define FM1_10GEC4_PHY_ADDR 0x01 /* Aquantia AQR113C 10G Base-T used by board revisions D and up */ #define AQR113C_PHY_ADDR1 0x00 #define AQR113C_PHY_ADDR2 0x08 #endif /* * USB */ /* * SDHC */ #ifdef CONFIG_MMC #define CFG_SYS_FSL_ESDHC_ADDR CFG_SYS_MPC85xx_ESDHC_ADDR #endif /* * Dynamic MTD Partition support with mtdparts */ /* * Environment */ /* * Miscellaneous configurable options */ /* * For booting Linux, the board info and command line data * have to be in the first 64 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ /* * Environment Configuration */ #define CONFIG_ROOTPATH "/opt/nfsroot" #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */ #define __USB_PHY_TYPE utmi #define CONFIG_EXTRA_ENV_SETTINGS \ "hwconfig=fsl_ddr:" \ "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) "," \ "bank_intlv=auto;" \ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ "netdev=eth0\0" \ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ "ubootaddr=" __stringify(CONFIG_TEXT_BASE) "\0" \ "tftpflash=tftpboot $loadaddr $uboot && " \ "protect off $ubootaddr +$filesize && " \ "erase $ubootaddr +$filesize && " \ "cp.b $loadaddr $ubootaddr $filesize && " \ "protect on $ubootaddr +$filesize && " \ "cmp.b $loadaddr $ubootaddr $filesize\0" \ "consoledev=ttyS0\0" \ "ramdiskaddr=2000000\0" \ "ramdiskfile=t2080rdb/ramdisk.uboot\0" \ "fdtaddr=1e00000\0" \ "fdtfile=t2080rdb/t2080rdb.dtb\0" \ "bdev=sda3\0" /* * For emulation this causes u-boot to jump to the start of the * proof point app code automatically */ #define PROOF_POINTS \ "setenv bootargs root=/dev/$bdev rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "cpu 1 release 0x29000000 - - -;" \ "cpu 2 release 0x29000000 - - -;" \ "cpu 3 release 0x29000000 - - -;" \ "cpu 4 release 0x29000000 - - -;" \ "cpu 5 release 0x29000000 - - -;" \ "cpu 6 release 0x29000000 - - -;" \ "cpu 7 release 0x29000000 - - -;" \ "go 0x29000000" #define HVBOOT \ "setenv bootargs config-addr=0x60000000; " \ "bootm 0x01000000 - 0x00f00000" #define ALU \ "setenv bootargs root=/dev/$bdev rw " \ "console=$consoledev,$baudrate $othbootargs;" \ "cpu 1 release 0x01000000 - - -;" \ "cpu 2 release 0x01000000 - - -;" \ "cpu 3 release 0x01000000 - - -;" \ "cpu 4 release 0x01000000 - - -;" \ "cpu 5 release 0x01000000 - - -;" \ "cpu 6 release 0x01000000 - - -;" \ "cpu 7 release 0x01000000 - - -;" \ "go 0x01000000" #include #endif /* __T2080RDB_H */