blob: 0f57e868a5d6d94c0364096204960d99f781c3c8 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
|
/*
* U-boot - Configuration file for PR1 Appliance
*
* based on bf537-stamp.h
* Copyright (c) Switchfin Org. <dpn@switchfin.org>
*/
#ifndef __CONFIG_PR1_H__
#define __CONFIG_PR1_H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf537-0.3
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 25000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 24
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 5
/*
* Memory Settings
*/
#define CONFIG_MEM_ADD_WDTH 11
#define CONFIG_MEM_SIZE 128
#define CONFIG_EBIU_SDRRC_VAL 0x306
#define CONFIG_EBIU_SDGCTL_VAL 0x8091998d
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_MALLOC_LEN (384 * 1024)
/*
* Network Settings
*/
#ifndef __ADSPBF534__
#define ADI_CMDS_NETWORK 1
#define CONFIG_BFIN_MAC
#define CONFIG_NETCONSOLE
#endif
#define CONFIG_HOSTNAME pr1
#define CONFIG_TFTP_BLOCKSIZE 4404
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
/*
* Flash Settings
*/
#define CONFIG_SYS_NO_FLASH /* We have no parallel FLASH */
/*
* SPI Settings
*/
#define CONFIG_BFIN_SPI
#define CONFIG_ENV_SPI_MAX_HZ 30000000
#define CONFIG_SF_DEFAULT_SPEED 30000000
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO
/*
* Env Storage Settings
*/
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET 0x10000
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x10000
#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
/*
* I2C Settings
*/
#define CONFIG_BFIN_TWI_I2C
#define CONFIG_HARD_I2C
/*
* NAND Settings
*/
#define CONFIG_NAND_PLAT
#define CONFIG_SYS_NAND_BASE 0x20000000
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2))
#define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1))
#define BFIN_NAND_WRITE(addr, cmd) \
do { \
bfin_write8(addr, cmd); \
SSYNC(); \
} while (0)
#define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd)
#define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd)
#define NAND_PLAT_GPIO_DEV_READY GPIO_PF9
/*
* Misc Settings
*/
#define CONFIG_BAUDRATE 115200
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
#define CONFIG_SYS_PROMPT "pr1>"
#define CONFIG_BOOTCOMMAND "run nandboot"
#define CONFIG_BOOTDELAY 2
#define CONFIG_LOADADDR 0x2000000
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
/*
* Overwrite some settings defined in bfin_adi_common.h
*/
#undef NAND_ENV_SETTINGS
#define NAND_ENV_SETTINGS \
"nandargs=set bootargs " CONFIG_BOOTARGS "\0" \
"nandboot=" \
"nand read $(loadaddr) 0x0 0x900000;" \
"run nandargs;" \
"bootm" \
"\0"
#endif
|
