ARM: atmel: at91sam9m10g45ek: enable spl support

Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.

As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.

Signed-off-by: Bo Shen <voice.shen@atmel.com>

7 files changed, 194 insertions, 1 deletions

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 30945c101bb..25da9262c56 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -66,6 +66,7 @@ config TARGET_STAMP9G20
 config TARGET_AT91SAM9M10G45EK
 	bool "Atmel AT91SAM9M10G45-EK board"
 	select CPU_ARM926EJS
+	select SUPPORT_SPL
 
 config TARGET_PM9G45
 	bool "Ronetix pm9g45 board"
diff --git a/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds b/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
new file mode 100644
index 00000000000..acadd1d4c43
--- /dev/null
+++ b/arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
@@ -0,0 +1,48 @@
+/*
+ * Copyright (C) 2015 Atmel Corporation
+ *		      Bo Shen <voice.shen@atmel.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE, \
+		LENGTH = CONFIG_SPL_MAX_SIZE }
+MEMORY { .sdram : ORIGIN = CONFIG_SPL_BSS_START_ADDR, \
+		LENGTH = CONFIG_SPL_BSS_MAX_SIZE }
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+	.text      :
+	{
+		__start = .;
+		*(.vectors)
+		arch/arm/cpu/arm926ejs/start.o	(.text*)
+		*(.text*)
+	} >.sram
+
+	. = ALIGN(4);
+	.rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram
+
+	. = ALIGN(4);
+	.data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
+
+	. = ALIGN(4);
+	__image_copy_end = .;
+
+	.end :
+	{
+		*(.__end)
+	} >.sram
+
+	.bss :
+	{
+		. = ALIGN(4);
+		__bss_start = .;
+		*(.bss*)
+		. = ALIGN(4);
+		__bss_end = .;
+	} >.sdram
+}
diff --git a/arch/arm/mach-at91/spl_at91.c b/arch/arm/mach-at91/spl_at91.c
index 89f588be45a..af6fc0d4c61 100644
--- a/arch/arm/mach-at91/spl_at91.c
+++ b/arch/arm/mach-at91/spl_at91.c
@@ -71,7 +71,11 @@ void __weak at91_spl_board_init(void)
 {
 }
 
-void spl_board_init(void)
+void __weak spl_board_init(void)
+{
+}
+
+void board_init_f(ulong dummy)
 {
 	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
 
diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
index b807ef9a425..4289179ee66 100644
--- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
+++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
@@ -8,6 +8,7 @@
 
 #include <common.h>
 #include <asm/io.h>
+#include <asm/arch/clk.h>
 #include <asm/arch/at91sam9g45_matrix.h>
 #include <asm/arch/at91sam9_smc.h>
 #include <asm/arch/at91_common.h>
@@ -15,6 +16,7 @@
 #include <asm/arch/gpio.h>
 #include <asm/arch/clk.h>
 #include <lcd.h>
+#include <linux/mtd/nand.h>
 #include <atmel_lcdc.h>
 #include <atmel_mci.h>
 #if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
@@ -71,6 +73,84 @@ void at91sam9m10g45ek_nand_hw_init(void)
 }
 #endif
 
+#if defined(CONFIG_SPL_BUILD)
+#include <spl.h>
+#include <nand.h>
+
+void at91_spl_board_init(void)
+{
+	/*
+	 * On the at91sam9m10g45ek board, the chip wm9711 stays in the
+	 * test mode, so it needs do some action to exit test mode.
+	 */
+	at91_periph_clk_enable(ATMEL_ID_PIODE);
+	at91_set_gpio_output(AT91_PIN_PD7, 0);
+	at91_set_gpio_output(AT91_PIN_PD8, 0);
+	at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1);
+	at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1);
+
+#ifdef CONFIG_SYS_USE_MMC
+	at91_mci_hw_init();
+#elif CONFIG_SYS_USE_NANDFLASH
+	at91sam9m10g45ek_nand_hw_init();
+#endif
+}
+
+#include <asm/arch/atmel_mpddrc.h>
+static void ddr2_conf(struct atmel_mpddr *ddr2)
+{
+	ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+	ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+		    ATMEL_MPDDRC_CR_NR_ROW_14 |
+		    ATMEL_MPDDRC_CR_DQMS_SHARED |
+		    ATMEL_MPDDRC_CR_CAS_DDR_CAS3);
+
+	ddr2->rtr = 0x24b;
+
+	ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */
+		      2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */
+		      2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */
+		      8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */
+		      2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */
+		      1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/
+		      1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */
+		      2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */
+
+	ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */
+		      200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
+		      16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
+		      14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
+
+	ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
+		      0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
+		      7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
+		      2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
+}
+
+void mem_init(void)
+{
+	struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+	struct at91_matrix *mat = (struct at91_matrix *)ATMEL_BASE_MATRIX;
+	struct atmel_mpddr ddr2;
+	unsigned long csa;
+
+	ddr2_conf(&ddr2);
+
+	/* enable DDR2 clock */
+	writel(0x4, &pmc->scer);
+
+	/* Chip select 1 is for DDR2/SDRAM */
+	csa = readl(&mat->ebicsa);
+	csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
+	csa &= ~AT91_MATRIX_EBI_VDDIOMSEL_3_3V;
+	writel(csa, &mat->ebicsa);
+
+	/* DDRAM2 Controller initialize */
+	ddr2_init(ATMEL_BASE_CS6, &ddr2);
+}
+#endif
+
 #ifdef CONFIG_CMD_USB
 static void at91sam9m10g45ek_usb_hw_init(void)
 {
diff --git a/configs/at91sam9m10g45ek_mmc_defconfig b/configs/at91sam9m10g45ek_mmc_defconfig
index 6949d3a0079..f3e1ebec931 100644
--- a/configs/at91sam9m10g45ek_mmc_defconfig
+++ b/configs/at91sam9m10g45ek_mmc_defconfig
@@ -1,3 +1,4 @@
+CONFIG_SPL=y
 CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_MMC"
 CONFIG_ARM=y
 CONFIG_ARCH_AT91=y
diff --git a/configs/at91sam9m10g45ek_nandflash_defconfig b/configs/at91sam9m10g45ek_nandflash_defconfig
index 30967e39c49..5e0b16e775a 100644
--- a/configs/at91sam9m10g45ek_nandflash_defconfig
+++ b/configs/at91sam9m10g45ek_nandflash_defconfig
@@ -1,3 +1,4 @@
+CONFIG_SPL=y
 CONFIG_SYS_EXTRA_OPTIONS="AT91SAM9M10G45,SYS_USE_NANDFLASH"
 CONFIG_ARM=y
 CONFIG_ARCH_AT91=y
diff --git a/include/configs/at91sam9m10g45ek.h b/include/configs/at91sam9m10g45ek.h
index db5d5ea846b..e4c49f4c147 100644
--- a/include/configs/at91sam9m10g45ek.h
+++ b/include/configs/at91sam9m10g45ek.h
@@ -203,4 +203,62 @@
  */
 #define CONFIG_SYS_MALLOC_LEN		ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
 
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_TEXT_BASE		0x300000
+#define CONFIG_SPL_MAX_SIZE		0x010000
+#define CONFIG_SPL_STACK		0x310000
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_GPIO_SUPPORT
+
+#define CONFIG_SYS_MONITOR_LEN		0x80000
+
+#ifdef CONFIG_SYS_USE_MMC
+
+#define CONFIG_SPL_BSS_START_ADDR	0x70000000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x00080000
+#define CONFIG_SYS_SPL_MALLOC_START	0x70080000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x00080000
+
+#define CONFIG_SPL_LDSCRIPT		arch/arm/mach-at91/arm926ejs/u-boot-spl.lds
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x400
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+
+#elif CONFIG_SYS_USE_NANDFLASH
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_SOFTECC
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE	0x80000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+
+#define CONFIG_SYS_NAND_PAGE_SIZE	0x800
+#define CONFIG_SYS_NAND_BLOCK_SIZE	0x20000
+#define CONFIG_SYS_NAND_PAGE_COUNT	64
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	NAND_LARGE_BADBLOCK_POS
+#define CONFIG_SYS_NAND_ECCSIZE		256
+#define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_SYS_NAND_OOBSIZE		64
+#define CONFIG_SYS_NAND_ECCPOS		{ 40, 41, 42, 43, 44, 45, 46, 47, \
+					  48, 49, 50, 51, 52, 53, 54, 55, \
+					  56, 57, 58, 59, 60, 61, 62, 63, }
+#endif
+
+#define CONFIG_SPL_ATMEL_SIZE
+#define CONFIG_SYS_MASTER_CLOCK		132096000
+#define CONFIG_SYS_AT91_PLLA		0x20c73f03
+#define CONFIG_SYS_MCKR			0x1301
+#define CONFIG_SYS_MCKR_CSS		0x1302
+
+#define ATMEL_BASE_MPDDRC		ATMEL_BASE_DDRSDRC0
 #endif