powerpc/p4080: Add support for the P4080DS board

Add support for the P4080DS board, with the following features:

* 36-bit only
* Boots from NOR flash
* FMAN drivers NOT supported
* SPD DDR initialization

Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Lan Chunhe-B25806 <b25806@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

12 files changed, 1494 insertions, 0 deletions

diff --git a/MAKEALL b/MAKEALL
index 2133559e82a..b34ae332884 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -428,6 +428,7 @@ LIST_85xx="		\
 	P2020RDB_NAND	\
 	P2020RDB_SDCARD	\
 	P2020RDB_SPIFLASH	\
+	P4080DS		\
 	PM854		\
 	PM856		\
 	sbc8540		\
diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 2d48d7ea328..f93045ff980 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -46,6 +46,7 @@ COBJS-$(CONFIG_MPC8536DS)	+= ics307_clk.o
 COBJS-$(CONFIG_MPC8572DS)	+= ics307_clk.o
 COBJS-$(CONFIG_P1022DS)		+= ics307_clk.o
 COBJS-$(CONFIG_P2020DS)		+= ics307_clk.o
+COBJS-$(CONFIG_P4080DS)		+= ics307_clk.o
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS-y))
diff --git a/board/freescale/corenet_ds/Makefile b/board/freescale/corenet_ds/Makefile
new file mode 100644
index 00000000000..8aa725523a2
--- /dev/null
+++ b/board/freescale/corenet_ds/Makefile
@@ -0,0 +1,55 @@
+#
+# Copyright 2007-2009 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS-y	+= $(BOARD).o
+COBJS-$(CONFIG_DDR_SPD)	+= ddr.o
+COBJS-$(CONFIG_PCI)	+= pci.o
+COBJS-y	+= law.o
+COBJS-y	+= tlb.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS-y))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+	rm -f $(OBJS) $(SOBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/freescale/corenet_ds/config.mk b/board/freescale/corenet_ds/config.mk
new file mode 100644
index 00000000000..72db24ebd2e
--- /dev/null
+++ b/board/freescale/corenet_ds/config.mk
@@ -0,0 +1,30 @@
+#
+# Copyright 2007-2009 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# P4080DS board
+#
+ifndef TEXT_BASE
+TEXT_BASE = 0xeff80000
+endif
+
+RESET_VECTOR_ADDRESS = 0xeffffffc
diff --git a/board/freescale/corenet_ds/corenet_ds.c b/board/freescale/corenet_ds/corenet_ds.c
new file mode 100644
index 00000000000..3cdefb34efc
--- /dev/null
+++ b/board/freescale/corenet_ds/corenet_ds.c
@@ -0,0 +1,259 @@
+/*
+ * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+
+extern void pci_of_setup(void *blob, bd_t *bd);
+
+#include "../common/ngpixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void cpu_mp_lmb_reserve(struct lmb *lmb);
+
+int checkboard (void)
+{
+	u8 sw;
+	struct cpu_type *cpu = gd->cpu;
+
+	printf("Board: %sDS, ", cpu->name);
+	printf("Sys ID: 0x%02x, Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
+		in_8(&pixis->id), in_8(&pixis->arch), in_8(&pixis->scver));
+
+	sw = in_8(&PIXIS_SW(PIXIS_LBMAP_SWITCH));
+	sw = (sw & PIXIS_LBMAP_MASK) >> PIXIS_LBMAP_SHIFT;
+
+	if (sw < 0x8)
+		printf("vBank: %d\n", sw);
+	else if (sw == 0x8)
+		puts("Promjet\n");
+	else if (sw == 0x9)
+		puts("NAND\n");
+	else
+		printf("invalid setting of SW%u\n", PIXIS_LBMAP_SWITCH);
+
+#ifdef CONFIG_PHYS_64BIT
+	puts("36-bit Addressing\n");
+#endif
+
+	/* Display the actual SERDES reference clocks as configured by the
+	 * dip switches on the board.  Note that the SWx registers could
+	 * technically be set to force the reference clocks to match the
+	 * values that the SERDES expects (or vice versa).  For now, however,
+	 * we just display both values and hope the user notices when they
+	 * don't match.
+	 */
+	puts("SERDES Reference Clocks: ");
+	sw = in_8(&PIXIS_SW(3));
+	printf("Bank1=%uMHz ", (sw & 0x40) ? 125 : 100);
+	printf("Bank2=%sMHz ", (sw & 0x20) ? "156.25" : "125");
+	printf("Bank3=%sMHz\n", (sw & 0x10) ? "156.25" : "125");
+
+	return 0;
+}
+
+int board_early_init_f(void)
+{
+	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+	/*
+	 * P4080 DS board only uses the DDR1_MCK0/3 and DDR2_MCK0/3
+	 * disable the DDR1_MCK1/2/4/5 and DDR2_MCK1/2/4/5 to reduce
+	 * the noise introduced by these unterminated and unused clock pairs.
+	 */
+	setbits_be32(&gur->ddrclkdr, 0x001B001B);
+
+	return 0;
+}
+
+int board_early_init_r(void)
+{
+	const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+	const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+	/*
+	 * Remap Boot flash + PROMJET region to caching-inhibited
+	 * so that flash can be erased properly.
+	 */
+
+	/* Flush d-cache and invalidate i-cache of any FLASH data */
+	flush_dcache();
+	invalidate_icache();
+
+	/* invalidate existing TLB entry for flash + promjet */
+	disable_tlb(flash_esel);
+
+	set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,	/* tlb, epn, rpn */
+			MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,	/* perms, wimge */
+			0, flash_esel, BOOKE_PAGESZ_256M, 1);	/* ts, esel, tsize, iprot */
+
+	set_liodns();
+	setup_portals();
+
+#ifdef CONFIG_SRIO1
+	if (is_serdes_configured(SRIO1)) {
+		set_next_law(CONFIG_SYS_RIO1_MEM_PHYS, LAW_SIZE_256M,
+				LAW_TRGT_IF_RIO_1);
+	} else {
+		printf ("    SRIO1: disabled\n");
+	}
+#else
+	setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_SRIO1); /* disable */
+#endif
+
+#ifdef CONFIG_SRIO2
+	if (is_serdes_configured(SRIO2)) {
+		set_next_law(CONFIG_SYS_RIO2_MEM_PHYS, LAW_SIZE_256M,
+				LAW_TRGT_IF_RIO_2);
+	} else {
+		printf ("    SRIO2: disabled\n");
+	}
+#else
+	setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_SRIO2); /* disable */
+#endif
+
+	return 0;
+}
+
+static const char *serdes_clock_to_string(u32 clock)
+{
+	switch(clock) {
+	case SRDS_PLLCR0_RFCK_SEL_100:
+		return "100";
+	case SRDS_PLLCR0_RFCK_SEL_125:
+		return "125";
+	case SRDS_PLLCR0_RFCK_SEL_156_25:
+		return "156.25";
+	default:
+		return "???";
+	}
+}
+
+#define NUM_SRDS_BANKS	3
+
+int misc_init_r(void)
+{
+	serdes_corenet_t *srds_regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+	u32 actual[NUM_SRDS_BANKS];
+	unsigned int i;
+	u8 sw3;
+
+	/* Warn if the expected SERDES reference clocks don't match the
+	 * actual reference clocks.  This needs to be done after calling
+	 * p4080_erratum_serdes8(), since that function may modify the clocks.
+	 */
+	sw3 = in_8(&PIXIS_SW(3));
+	actual[0] = (sw3 & 0x40) ?
+		SRDS_PLLCR0_RFCK_SEL_125 : SRDS_PLLCR0_RFCK_SEL_100;
+	actual[1] = (sw3 & 0x20) ?
+		SRDS_PLLCR0_RFCK_SEL_156_25 : SRDS_PLLCR0_RFCK_SEL_125;
+	actual[2] = (sw3 & 0x10) ?
+		SRDS_PLLCR0_RFCK_SEL_156_25 : SRDS_PLLCR0_RFCK_SEL_125;
+
+	for (i = 0; i < NUM_SRDS_BANKS; i++) {
+		u32 expected = srds_regs->bank[i].pllcr0 & SRDS_PLLCR0_RFCK_SEL_MASK;
+		if (expected != actual[i]) {
+			printf("Warning: SERDES bank %u expects reference clock"
+			       " %sMHz, but actual is %sMHz\n", i + 1,
+			       serdes_clock_to_string(expected),
+			       serdes_clock_to_string(actual[i]));
+		}
+	}
+
+	return 0;
+}
+
+phys_size_t initdram(int board_type)
+{
+	phys_size_t dram_size;
+
+	puts("Initializing....\n");
+
+	dram_size = fsl_ddr_sdram();
+
+	setup_ddr_tlbs(dram_size / 0x100000);
+
+	puts("    DDR: ");
+	return dram_size;
+}
+
+#ifdef CONFIG_MP
+void board_lmb_reserve(struct lmb *lmb)
+{
+	cpu_mp_lmb_reserve(lmb);
+}
+#endif
+
+void ft_srio_setup(void *blob)
+{
+#ifdef CONFIG_SRIO1
+	if (!is_serdes_configured(SRIO1)) {
+		fdt_del_node_and_alias(blob, "rio0");
+	}
+#else
+	fdt_del_node_and_alias(blob, "rio0");
+#endif
+#ifdef CONFIG_SRIO2
+	if (!is_serdes_configured(SRIO2)) {
+		fdt_del_node_and_alias(blob, "rio1");
+	}
+#else
+	fdt_del_node_and_alias(blob, "rio1");
+#endif
+}
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+	phys_addr_t base;
+	phys_size_t size;
+
+	ft_cpu_setup(blob, bd);
+
+	ft_srio_setup(blob);
+
+	base = getenv_bootm_low();
+	size = getenv_bootm_size();
+
+	fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+	pci_of_setup(blob, bd);
+#endif
+
+	fdt_fixup_liodn(blob);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	return pci_eth_init(bis);
+}
diff --git a/board/freescale/corenet_ds/ddr.c b/board/freescale/corenet_ds/ddr.c
new file mode 100644
index 00000000000..82b2b4f5503
--- /dev/null
+++ b/board/freescale/corenet_ds/ddr.c
@@ -0,0 +1,176 @@
+/*
+ * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * Version 2 as published by the Free Software Foundation.
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+static void get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+	int ret;
+
+	ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr3_spd_eeprom_t));
+	if (ret) {
+		debug("DDR: failed to read SPD from address %u\n", i2c_address);
+		memset(spd, 0, sizeof(ddr3_spd_eeprom_t));
+	}
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+	return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd,
+		      unsigned int ctrl_num)
+{
+	unsigned int i;
+	unsigned int i2c_address = 0;
+
+	for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+		if (ctrl_num == 0 && i == 0)
+			i2c_address = SPD_EEPROM_ADDRESS1;
+		else if (ctrl_num == 1 && i == 0)
+			i2c_address = SPD_EEPROM_ADDRESS2;
+
+		get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+	}
+}
+
+typedef struct {
+	u32 datarate_mhz_low;
+	u32 datarate_mhz_high;
+	u32 n_ranks;
+	u32 clk_adjust;
+	u32 cpo;
+	u32 write_data_delay;
+	u32 force_2T;
+} board_specific_parameters_t;
+
+/* ranges for parameters:
+ *  wr_data_delay = 0-6
+ *  clk adjust = 0-8
+ *  cpo 2-0x1E (30)
+ */
+
+
+/* XXX: these values need to be checked for all interleaving modes.  */
+/* XXX: No reliable dual-rank 800 MHz setting has been found.  It may
+ *      seem reliable, but errors will appear when memory intensive
+ *      program is run. */
+/* XXX: Single rank at 800 MHz is OK.  */
+const board_specific_parameters_t board_specific_parameters[][20] = {
+	{
+	/* 	memory controller 0 			*/
+	/*	  lo|  hi|  num|  clk| cpo|wrdata|2T	*/
+	/*	 mhz| mhz|ranks|adjst|    | delay|	*/
+		{  0, 333,    2,    6,   7,    3,  0},
+		{334, 400,    2,    6,   9,    3,  0},
+		{401, 549,    2,    6,  11,    3,  0},
+		{550, 680,    2,    1,  10,    5,  0},
+		{681, 850,    2,    1,  12,    5,  0},
+		{851, 1050,   2,    1,  12,    5,  0},
+		{1051, 1250,  2,    1,  15,    4,  0},
+		{1251, 1350,  2,    1,  15,    4,  0},
+		{  0, 333,    1,    6,   7,    3,  0},
+		{334, 400,    1,    6,   9,    3,  0},
+		{401, 549,    1,    6,  11,    3,  0},
+		{550, 680,    1,    1,  10,    5,  0},
+		{681, 850,    1,    1,  12,    5,  0}
+	},
+
+	{
+	/*	memory controller 1			*/
+	/*	  lo|  hi|  num|  clk| cpo|wrdata|2T	*/
+	/*	 mhz| mhz|ranks|adjst|    | delay|	*/
+		{  0, 333,    2,     6,  7,    3,  0},
+		{334, 400,    2,     6,  9,    3,  0},
+		{401, 549,    2,     6, 11,    3,  0},
+		{550, 680,    2,     1, 11,    6,  0},
+		{681, 850,    2,     1, 13,    6,  0},
+		{851, 1050,   2,     1, 13,    6,  0},
+		{1051, 1250,  2,     1, 15,    4,  0},
+		{1251, 1350,  2,     1, 15,    4,  0},
+		{  0, 333,    1,     6,  7,    3,  0},
+		{334, 400,    1,     6,  9,    3,  0},
+		{401, 549,    1,     6, 11,    3,  0},
+		{550, 680,    1,     1, 11,    6,  0},
+		{681, 850,    1,     1, 13,    6,  0}
+	}
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+				dimm_params_t *pdimm,
+				unsigned int ctrl_num)
+{
+	const board_specific_parameters_t *pbsp =
+				&(board_specific_parameters[ctrl_num][0]);
+	u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
+				sizeof(board_specific_parameters[0][0]);
+	u32 i;
+	ulong ddr_freq;
+
+	/* set odt_rd_cfg and odt_wr_cfg. If the there is only one dimm in
+	 * that controller, set odt_wr_cfg to 4 for CS0, and 0 to CS1. If
+	 * there are two dimms in the controller, set odt_rd_cfg to 3 and
+	 * odt_wr_cfg to 3 for the even CS, 0 for the odd CS.
+	 */
+	for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
+		if (i&1) {	/* odd CS */
+			popts->cs_local_opts[i].odt_rd_cfg = 0;
+			popts->cs_local_opts[i].odt_wr_cfg = 1;
+		} else {	/* even CS */
+			if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) {
+				popts->cs_local_opts[i].odt_rd_cfg = 0;
+				popts->cs_local_opts[i].odt_wr_cfg = 1;
+			} else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) {
+			popts->cs_local_opts[i].odt_rd_cfg = 3;
+			popts->cs_local_opts[i].odt_wr_cfg = 3;
+			}
+		}
+	}
+
+	/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
+	 * freqency and n_banks specified in board_specific_parameters table.
+	 */
+	ddr_freq = get_ddr_freq(0) / 1000000;
+	for (i = 0; i < num_params; i++) {
+		if (ddr_freq >= pbsp->datarate_mhz_low &&
+		    ddr_freq <= pbsp->datarate_mhz_high &&
+		    pdimm->n_ranks == pbsp->n_ranks) {
+			popts->cpo_override = 0xff; /* force auto CPO calibration */
+			popts->write_data_delay = 2;
+			popts->clk_adjust = 5; /* Force value to be 5/8 clock cycle */
+			popts->twoT_en = pbsp->force_2T;
+		}
+		pbsp++;
+	}
+
+	/*
+	 * Factors to consider for half-strength driver enable:
+	 *	- number of DIMMs installed
+	 */
+	popts->half_strength_driver_enable = 0;
+	/*
+	 * Write leveling override
+	 */
+	popts->wrlvl_override = 1;
+	popts->wrlvl_sample = 0xa;
+	popts->wrlvl_start = 0x7;
+	/*
+	 * Rtt and Rtt_WR override
+	 */
+	popts->rtt_override = 1;
+	popts->rtt_override_value = DDR3_RTT_120_OHM;
+	popts->rtt_wr_override_value = 0; /* Rtt_WR= dynamic ODT off */
+
+	/* Enable ZQ calibration */
+	popts->zq_en = 1;
+}
diff --git a/board/freescale/corenet_ds/law.c b/board/freescale/corenet_ds/law.c
new file mode 100644
index 00000000000..43b4b97de18
--- /dev/null
+++ b/board/freescale/corenet_ds/law.c
@@ -0,0 +1,40 @@
+/*
+ * Copyright 2008-2010 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_BMAN),
+	SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_2M, LAW_TRGT_IF_QMAN),
+	SET_LAW(PIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/corenet_ds/pci.c b/board/freescale/corenet_ds/pci.c
new file mode 100644
index 00000000000..2994e366c21
--- /dev/null
+++ b/board/freescale/corenet_ds/pci.c
@@ -0,0 +1,127 @@
+/*
+ * Copyright 2007-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+#ifdef CONFIG_PCIE1
+static struct pci_controller pcie1_hose;
+#endif
+
+#ifdef CONFIG_PCIE2
+static struct pci_controller pcie2_hose;
+#endif
+
+#ifdef CONFIG_PCIE3
+static struct pci_controller pcie3_hose;
+#endif
+
+void pci_init_board(void)
+{
+	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+	struct fsl_pci_info pci_info[3];
+	u32 devdisr;
+	int first_free_busno = 0;
+	int num = 0;
+
+	int pcie_ep, pcie_configured;
+
+	devdisr = in_be32(&gur->devdisr);
+
+	debug ("   pci_init_board: devdisr=%x\n", devdisr);
+
+#ifdef CONFIG_PCIE1
+	pcie_configured = is_serdes_configured(PCIE1);
+
+	if (pcie_configured && !(devdisr & FSL_CORENET_DEVDISR_PCIE1)) {
+		set_next_law(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_512M,
+				LAW_TRGT_IF_PCIE_1);
+		set_next_law(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_64K,
+				LAW_TRGT_IF_PCIE_1);
+		SET_STD_PCIE_INFO(pci_info[num], 1);
+		pcie_ep = fsl_setup_hose(&pcie1_hose, pci_info[num].regs);
+		printf("    PCIE1 connected to Slot 1 as %s (base addr %lx)\n",
+				pcie_ep ? "End Point" : "Root Complex",
+				pci_info[num].regs);
+		first_free_busno = fsl_pci_init_port(&pci_info[num++],
+				&pcie1_hose, first_free_busno);
+	} else {
+		printf ("    PCIE1: disabled\n");
+	}
+#else
+	setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_PCIE1); /* disable */
+#endif
+
+#ifdef CONFIG_PCIE2
+	pcie_configured = is_serdes_configured(PCIE2);
+
+	if (pcie_configured && !(devdisr & FSL_CORENET_DEVDISR_PCIE2)) {
+		set_next_law(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_512M,
+				LAW_TRGT_IF_PCIE_2);
+		set_next_law(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_64K,
+				LAW_TRGT_IF_PCIE_2);
+		SET_STD_PCIE_INFO(pci_info[num], 2);
+		pcie_ep = fsl_setup_hose(&pcie2_hose, pci_info[num].regs);
+		printf("    PCIE2 connected to Slot 3 as %s (base addr %lx)\n",
+				pcie_ep ? "End Point" : "Root Complex",
+				pci_info[num].regs);
+		first_free_busno = fsl_pci_init_port(&pci_info[num++],
+				&pcie2_hose, first_free_busno);
+	} else {
+		printf ("    PCIE2: disabled\n");
+	}
+#else
+	setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_PCIE2); /* disable */
+#endif
+
+#ifdef CONFIG_PCIE3
+	pcie_configured = is_serdes_configured(PCIE3);
+
+	if (pcie_configured && !(devdisr & FSL_CORENET_DEVDISR_PCIE3)) {
+		set_next_law(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_512M,
+				LAW_TRGT_IF_PCIE_3);
+		set_next_law(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_64K,
+				LAW_TRGT_IF_PCIE_3);
+		SET_STD_PCIE_INFO(pci_info[num], 3);
+		pcie_ep = fsl_setup_hose(&pcie3_hose, pci_info[num].regs);
+		printf("    PCIE3 connected to Slot 2 as %s (base addr %lx)\n",
+				pcie_ep ? "End Point" : "Root Complex",
+				pci_info[num].regs);
+		first_free_busno = fsl_pci_init_port(&pci_info[num++],
+				&pcie3_hose, first_free_busno);
+	} else {
+		printf ("    PCIE3: disabled\n");
+	}
+#else
+	setbits_be32(&gur->devdisr, FSL_CORENET_DEVDISR_PCIE3); /* disable */
+#endif
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+	FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/corenet_ds/tlb.c b/board/freescale/corenet_ds/tlb.c
new file mode 100644
index 00000000000..1ae0416248c
--- /dev/null
+++ b/board/freescale/corenet_ds/tlb.c
@@ -0,0 +1,112 @@
+/*
+ * Copyright 2008-2010 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+	/* TLB 0 - for temp stack in cache */
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+	SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+		      CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	SET_TLB_ENTRY(0, PIXIS_BASE, PIXIS_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_4K, 0),
+
+	/* TLB 1 */
+	/* *I*** - Covers boot page */
+	SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 0, BOOKE_PAGESZ_4K, 1),
+
+	/* *I*G* - CCSRBAR */
+	SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 1, BOOKE_PAGESZ_16M, 1),
+
+	/* *I*G* - Flash, localbus */
+	/* This will be changed to *I*G* after relocation to RAM. */
+	SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+		      MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+		      0, 2, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 3, BOOKE_PAGESZ_1G, 1),
+
+	/* *I*G* - PCI */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x40000000,
+		      CONFIG_SYS_PCIE1_MEM_PHYS + 0x40000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 4, BOOKE_PAGESZ_256M, 1),
+
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT + 0x50000000,
+		      CONFIG_SYS_PCIE1_MEM_PHYS + 0x50000000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 5, BOOKE_PAGESZ_256M, 1),
+
+	/* *I*G* - PCI I/O */
+	SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 6, BOOKE_PAGESZ_256K, 1),
+
+	/* Bman/Qman */
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 9, BOOKE_PAGESZ_1M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x00100000,
+		      CONFIG_SYS_BMAN_MEM_PHYS + 0x00100000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 10, BOOKE_PAGESZ_1M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, 0,
+		      0, 11, BOOKE_PAGESZ_1M, 1),
+	SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x00100000,
+		      CONFIG_SYS_QMAN_MEM_PHYS + 0x00100000,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 12, BOOKE_PAGESZ_1M, 1),
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+	SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 13, BOOKE_PAGESZ_4M, 1),
+#endif
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/boards.cfg b/boards.cfg
index b82f530f46a..a70f541bd4b 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -343,6 +343,7 @@ MPC8540ADS	powerpc	mpc85xx		mpc8540ads	freescale
 MPC8544DS	powerpc	mpc85xx		mpc8544ds	freescale
 MPC8560ADS	powerpc	mpc85xx		mpc8560ads	freescale
 MPC8568MDS	powerpc	mpc85xx		mpc8568mds	freescale
+P4080DS		powerpc	mpc85xx		corenet_ds	freescale
 XPEDITE5200	powerpc	mpc85xx		xpedite5200	xes
 XPEDITE5370	powerpc	mpc85xx		xpedite5370	xes
 P1022DS		powerpc	mpc85xx		p1022ds		freescale
diff --git a/include/configs/P4080DS.h b/include/configs/P4080DS.h
new file mode 100644
index 00000000000..87703c98b3c
--- /dev/null
+++ b/include/configs/P4080DS.h
@@ -0,0 +1,39 @@
+/*
+ * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * P4080 DS board configuration file
+ */
+#define CONFIG_P4080DS
+#define CONFIG_PHYS_64BIT
+#define CONFIG_PPC_P4080
+#define CONFIG_SYS_NUM_FMAN		2
+#define CONFIG_SYS_NUM_FM1_DTSEC	4
+#define CONFIG_SYS_NUM_FM2_DTSEC	4
+#define CONFIG_SYS_NUM_FM1_10GEC	1
+#define CONFIG_SYS_NUM_FM2_10GEC	1
+#define CONFIG_NUM_DDR_CONTROLLERS	2
+
+#define CONFIG_SYS_P4080_ERRATUM_CPU22
+#define CONFIG_SYS_P4080_ERRATUM_SERDES8
+
+#include "corenet_ds.h"
diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h
new file mode 100644
index 00000000000..dd609da8f06
--- /dev/null
+++ b/include/configs/corenet_ds.h
@@ -0,0 +1,653 @@
+/*
+ * Copyright 2009-2010 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * Corenet DS style board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "../board/freescale/common/ics307_clk.h"
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500			/* BOOKE e500 family */
+#define CONFIG_E500MC			/* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
+#define CONFIG_MPC85xx			/* MPC85xx/PQ3 platform */
+#define CONFIG_FSL_CORENET		/* Freescale CoreNet platform */
+#define CONFIG_MP			/* support multiple processors */
+
+#define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC		CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_ELBC			/* Has Enhanced localbus controller */
+#define CONFIG_PCI			/* Enable PCI/PCIE */
+#define CONFIG_PCIE1			/* PCIE controler 1 */
+#define CONFIG_PCIE2			/* PCIE controler 2 */
+#define CONFIG_PCIE3			/* PCIE controler 3 */
+#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
+#define CONFIG_SYS_HAS_SERDES		/* has SERDES */
+
+#define CONFIG_SRIO1			/* SRIO port 1 */
+#define CONFIG_SRIO2			/* SRIO port 2 */
+
+#define CONFIG_FSL_LAW			/* Use common FSL init code */
+
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_NOWHERE
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#endif
+
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk() /* sysclk for MPC85xx */
+#define CONFIG_ICS307_REFCLK_HZ	33333000  /* ICS307 clock chip ref freq */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
+#define CONFIG_BTB			/* toggle branch predition */
+//#define	CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#endif
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP		64	/* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT	0xfe000000	/* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR		0xfe000000	/* relocated CCSRBAR */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS		0xffe000000ull	/* physical addr of CCSRBAR */
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS	CONFIG_SYS_CCSRBAR	/* physical addr of CCSRBAR */
+#endif
+#define CONFIG_SYS_IMMR		CONFIG_SYS_CCSRBAR	/* PQII uses CONFIG_SYS_IMMR */
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_DCSRBAR		0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
+#endif
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM	0
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+#define CONFIG_FSL_DDR3
+
+#ifdef CONFIG_DDR_SPD
+#define CONFIG_SYS_SPD_BUS_NUM	1
+#define SPD_EEPROM_ADDRESS1	0x51
+#define SPD_EEPROM_ADDRESS2	0x52
+#else
+#define CONFIG_SYS_SDRAM_SIZE		4096
+
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000003f
+#define CONFIG_SYS_DDR_CS1_BNDS		0x0040007f
+#define CONFIG_SYS_DDR_CS0_CONFIG	0x80014202
+#define CONFIG_SYS_DDR_CS1_CONFIG	0x80014202
+#define CONFIG_SYS_DDR_TIMING_3		0x01031000
+#define CONFIG_SYS_DDR_TIMING_0		0x55440804
+#define CONFIG_SYS_DDR_TIMING_1		0x74713a66
+#define CONFIG_SYS_DDR_TIMING_2		0x0fb8911b
+#define CONFIG_SYS_DDR_MODE_1		0x00421850
+#define CONFIG_SYS_DDR_MODE_2		0x00100000
+#define CONFIG_SYS_DDR_MODE_CTRL	0x00000000
+#define CONFIG_SYS_DDR_INTERVAL		0x10400100
+#define CONFIG_SYS_DDR_DATA_INIT	0xdeadbeef
+#define CONFIG_SYS_DDR_CLK_CTRL		0x03000000
+#define CONFIG_SYS_DDR_TIMING_4		0x00220001
+#define CONFIG_SYS_DDR_TIMING_5		0x03401500
+#define CONFIG_SYS_DDR_ZQ_CNTL		0x89080600
+#define CONFIG_SYS_DDR_WRLVL_CNTL	0x8655a608
+#define CONFIG_SYS_DDR_CONTROL		0xc7048000
+#define CONFIG_SYS_DDR_CONTROL2		0x24400011
+#define CONFIG_SYS_DDR_CDR1		0x00000000
+#define CONFIG_SYS_DDR_CDR2		0x00000000
+#define CONFIG_SYS_DDR_ERR_INT_EN	0x0000000d
+#define CONFIG_SYS_DDR_ERR_DIS		0x00000000
+#define CONFIG_SYS_DDR_SBE		0x00010000
+#define CONFIG_SYS_DDR_DEBUG_18		0x40100400
+
+#define CONFIG_SYS_DDR2_CS0_BNDS	0x008000bf
+#define CONFIG_SYS_DDR2_CS1_BNDS	0x00C000ff
+#define CONFIG_SYS_DDR2_CS0_CONFIG	CONFIG_SYS_DDR_CS0_CONFIG
+#define CONFIG_SYS_DDR2_CS1_CONFIG	CONFIG_SYS_DDR_CS1_CONFIG
+#define CONFIG_SYS_DDR2_TIMING_3	CONFIG_SYS_DDR_TIMING_3
+#define CONFIG_SYS_DDR2_TIMING_0	CONFIG_SYS_DDR_TIMING_0
+#define CONFIG_SYS_DDR2_TIMING_1	CONFIG_SYS_DDR_TIMING_1
+#define CONFIG_SYS_DDR2_TIMING_2	CONFIG_SYS_DDR_TIMING_2
+#define CONFIG_SYS_DDR2_MODE_1		CONFIG_SYS_DDR_MODE_1
+#define CONFIG_SYS_DDR2_MODE_2		CONFIG_SYS_DDR_MODE_2
+#define CONFIG_SYS_DDR2_MODE_CTRL	CONFIG_SYS_DDR_MODE_CTRL
+#define CONFIG_SYS_DDR2_INTERVAL	CONFIG_SYS_DDR_INTERVAL
+#define CONFIG_SYS_DDR2_DATA_INIT	CONFIG_SYS_DDR_DATA_INIT
+#define CONFIG_SYS_DDR2_CLK_CTRL	CONFIG_SYS_DDR_CLK_CTRL
+#define CONFIG_SYS_DDR2_TIMING_4	CONFIG_SYS_DDR_TIMING_4
+#define CONFIG_SYS_DDR2_TIMING_5	CONFIG_SYS_DDR_TIMING_5
+#define CONFIG_SYS_DDR2_ZQ_CNTL		CONFIG_SYS_DDR_ZQ_CNTL
+#define CONFIG_SYS_DDR2_WRLVL_CNTL	CONFIG_SYS_DDR_WRLVL_CNTL
+#define CONFIG_SYS_DDR2_CONTROL		CONFIG_SYS_DDR_CONTROL
+#define CONFIG_SYS_DDR2_CONTROL2	CONFIG_SYS_DDR_CONTROL2
+#define CONFIG_SYS_DDR2_CDR1		CONFIG_SYS_DDR_CDR1
+#define CONFIG_SYS_DDR2_CDR2		CONFIG_SYS_DDR_CDR2
+#define CONFIG_SYS_DDR2_ERR_INT_EN	CONFIG_SYS_DDR_ERR_INT_EN
+#define CONFIG_SYS_DDR2_ERR_DIS		CONFIG_SYS_DDR_ERR_DIS
+#define CONFIG_SYS_DDR2_SBE		CONFIG_SYS_DDR_SBE
+#define CONFIG_SYS_DDR2_DEBUG_18	CONFIG_SYS_DDR_DEBUG_18
+
+#endif
+
+/*
+ * Local Bus Definitions
+ */
+
+/* Set the local bus clock 1/8 of platform clock */
+#define CONFIG_SYS_LBC_LCRR		LCRR_CLKDIV_8
+
+#define CONFIG_SYS_FLASH_BASE		0xe0000000	/* Start of PromJet */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS	0xfe0000000ull
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS	CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_SYS_BR0_PRELIM \
+	(BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | \
+	 BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR0_PRELIM	((0xf8000ff7 & ~OR_GPCM_SCY & ~OR_GPCM_EHTR) \
+					| OR_GPCM_SCY_8 | OR_GPCM_EHTR_CLEAR)
+
+#define CONFIG_SYS_BR1_PRELIM \
+	(BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
+#define CONFIG_SYS_OR1_PRELIM	0xf8000ff7
+
+#define CONFIG_FSL_NGPIXIS		/* use common ngPIXIS code */
+#define PIXIS_BASE		0xffdf0000	/* PIXIS registers */
+#ifdef CONFIG_PHYS_64BIT
+#define PIXIS_BASE_PHYS		0xfffdf0000ull
+#else
+#define PIXIS_BASE_PHYS		PIXIS_BASE
+#endif
+
+#define CONFIG_SYS_BR3_PRELIM	(BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
+#define CONFIG_SYS_OR3_PRELIM	0xffffeff7	/* 32KB but only 4k mapped */
+
+#define PIXIS_LBMAP_SWITCH	7
+#define PIXIS_LBMAP_MASK	0xf0
+#define PIXIS_LBMAP_SHIFT	4
+#define PIXIS_LBMAP_ALTBANK	0x40
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024		/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_MONITOR_BASE		TEXT_BASE	/* start of monitor */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS	CONFIG_SYS_INIT_RAM_ADDR /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_END		0x00004000	/* End of used area in RAM */
+
+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_FSL_I2C		/* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_OFFSET		0x118000
+#define CONFIG_SYS_I2C2_OFFSET		0x118100
+
+/*
+ * RapidIO
+ */
+#define CONFIG_SYS_RIO1_MEM_VIRT	0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_RIO1_MEM_PHYS	0xc20000000ull
+#else
+#define CONFIG_SYS_RIO1_MEM_PHYS	0xa0000000
+#endif
+#define CONFIG_SYS_RIO1_MEM_SIZE	0x10000000	/* 256M */
+
+#define CONFIG_SYS_RIO2_MEM_VIRT	0xb0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_RIO2_MEM_PHYS	0xc30000000ull
+#else
+#define CONFIG_SYS_RIO2_MEM_PHYS	0xb0000000
+#endif
+#define CONFIG_SYS_RIO2_MEM_SIZE	0x10000000	/* 256M */
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xf8000000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xa0000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xf8010000
+#endif
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT	0xe0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc40000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xc0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc0000000
+#endif
+#define CONFIG_SYS_PCIE3_MEM_SIZE	0x20000000	/* 512M */
+#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
+#else
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xf8020000
+#endif
+#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
+
+/* Qman/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS	10
+#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
+#else
+#define CONFIG_SYS_BMAN_MEM_PHYS	CONFIG_SYS_BMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_BMAN_MEM_SIZE	0x00200000
+#define CONFIG_SYS_QMAN_NUM_PORTALS	10
+#define CONFIG_SYS_QMAN_MEM_BASE	0xf4200000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_QMAN_MEM_PHYS	0xff4200000ull
+#else
+#define CONFIG_SYS_QMAN_MEM_PHYS	CONFIG_SYS_QMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_QMAN_MEM_SIZE	0x00200000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+/* Default address of microcode for the Linux Fman driver */
+#define CONFIG_SYS_FMAN_FW_ADDR		0xEF000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FMAN_FW_ADDR_PHYS	0xFEF000000ULL
+#else
+#define CONFIG_SYS_FMAN_FW_ADDR_PHYS	CONFIG_SYS_FMAN_FW_ADDR
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#endif
+
+#ifdef CONFIG_PCI
+
+/*PCIE video card used*/
+#define VIDEO_IO_OFFSET		CONFIG_SYS_PCIE1_IO_VIRT
+
+/* video */
+#define CONFIG_VIDEO
+
+#ifdef CONFIG_VIDEO
+#define CONFIG_BIOSEMU
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#endif
+
+#define CONFIG_NET_MULTI
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+#define CONFIG_E1000
+
+#ifndef CONFIG_PCI_PNP
+#define PCI_ENET0_IOADDR		CONFIG_SYS_PCI1_IO_BUS
+#define PCI_ENET0_MEMADDR		CONFIG_SYS_PCI1_IO_BUS
+#define PCI_IDSEL_NUMBER		0x11	/* IDSEL = AD11 */
+#endif
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif	/* CONFIG_PCI */
+
+/* SATA */
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CONFIG_SYS_SATA_MAX_DEVICE	2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
+
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR	0x1c
+#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR	0x1d
+#define CONFIG_SYS_FM1_DTSEC3_PHY_ADDR	0x1e
+#define CONFIG_SYS_FM1_DTSEC4_PHY_ADDR	0x1f
+#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR	4
+
+#if (CONFIG_SYS_NUM_FMAN == 2)
+#define CONFIG_SYS_FM2_DTSEC1_PHY_ADDR	0x1c
+#define CONFIG_SYS_FM2_DTSEC2_PHY_ADDR	0x1d
+#define CONFIG_SYS_FM2_DTSEC3_PHY_ADDR	0x1e
+#define CONFIG_SYS_FM2_DTSEC4_PHY_ADDR	0x1f
+#define CONFIG_SYS_FM2_10GEC1_PHY_ADDR	0
+#endif
+
+#define CONFIG_SYS_TBIPA_VALUE	8
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"FM1@DTSEC1"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+* USB
+*/
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(16 << 20)	/* Initial Memory map for Linux*/
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH		/opt/nfsroot
+#define CONFIG_BOOTFILE		uImage
+#define CONFIG_UBOOTPATH	u-boot.bin	/* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY 	10	/* -1 disables auto-boot */
+
+#define CONFIG_BAUDRATE	115200
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"netdev=eth0\0"						\
+	"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"			\
+	"tftpflash=tftpboot $loadaddr $uboot; "			\
+	"protect off " MK_STR(TEXT_BASE) " +$filesize; "	\
+	"erase " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "	\
+	"protect on " MK_STR(TEXT_BASE) " +$filesize; "		\
+	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"	\
+	"consoledev=ttyS0\0"					\
+	"ramdiskaddr=2000000\0"					\
+	"ramdiskfile=p4080ds/ramdisk.uboot\0"			\
+	"fdtaddr=c00000\0"					\
+	"fdtfile=p4080ds/p4080ds.dtb\0"				\
+	"bdev=sda3\0"						\
+	"c=ffe\0"						\
+	"fman_ucode="MK_STR(CONFIG_SYS_FMAN_FW_ADDR_PHYS)"\0"
+
+#define CONFIG_HDBOOT					\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND			\
+	"setenv bootargs root=/dev/nfs rw "	\
+	"nfsroot=$serverip:$rootpath "		\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $ramdiskaddr $ramdiskfile;"		\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_HDBOOT
+
+#endif	/* __CONFIG_H */