Convert CONFIG_ENV_IS_IN_EEPROM to Kconfig

This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_EEPROM

Signed-off-by: Simon Glass <sjg@chromium.org>

1 files changed, 0 insertions, 60 deletions

diff --git a/README b/README
index f37765e51cb..01bdd3425f6 100644
--- a/README
+++ b/README
@@ -3422,66 +3422,6 @@ environment in RAM: we could work on NVRAM directly, but we want to
 keep settings there always unmodified except somebody uses "saveenv"
 to save the current settings.
 
-
-- CONFIG_ENV_IS_IN_EEPROM:
-
-	Use this if you have an EEPROM or similar serial access
-	device and a driver for it.
-
-	- CONFIG_ENV_OFFSET:
-	- CONFIG_ENV_SIZE:
-
-	  These two #defines specify the offset and size of the
-	  environment area within the total memory of your EEPROM.
-
-	- CONFIG_SYS_I2C_EEPROM_ADDR:
-	  If defined, specified the chip address of the EEPROM device.
-	  The default address is zero.
-
-	- CONFIG_SYS_I2C_EEPROM_BUS:
-	  If defined, specified the i2c bus of the EEPROM device.
-
-	- CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
-	  If defined, the number of bits used to address bytes in a
-	  single page in the EEPROM device.  A 64 byte page, for example
-	  would require six bits.
-
-	- CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
-	  If defined, the number of milliseconds to delay between
-	  page writes.	The default is zero milliseconds.
-
-	- CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
-	  The length in bytes of the EEPROM memory array address.  Note
-	  that this is NOT the chip address length!
-
-	- CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
-	  EEPROM chips that implement "address overflow" are ones
-	  like Catalyst 24WC04/08/16 which has 9/10/11 bits of
-	  address and the extra bits end up in the "chip address" bit
-	  slots. This makes a 24WC08 (1Kbyte) chip look like four 256
-	  byte chips.
-
-	  Note that we consider the length of the address field to
-	  still be one byte because the extra address bits are hidden
-	  in the chip address.
-
-	- CONFIG_SYS_EEPROM_SIZE:
-	  The size in bytes of the EEPROM device.
-
-	- CONFIG_ENV_EEPROM_IS_ON_I2C
-	  define this, if you have I2C and SPI activated, and your
-	  EEPROM, which holds the environment, is on the I2C bus.
-
-	- CONFIG_I2C_ENV_EEPROM_BUS
-	  if you have an Environment on an EEPROM reached over
-	  I2C muxes, you can define here, how to reach this
-	  EEPROM. For example:
-
-	  #define CONFIG_I2C_ENV_EEPROM_BUS	  1
-
-	  EEPROM which holds the environment, is reached over
-	  a pca9547 i2c mux with address 0x70, channel 3.
-
 - CONFIG_ENV_IS_IN_DATAFLASH:
 
 	Define this if you have a DataFlash memory device which you