diff options
author | Tom Rini | 2021-12-11 14:55:51 -0500 |
---|---|---|
committer | Tom Rini | 2021-12-27 08:41:38 -0500 |
commit | f76750d1113380462413bad94d7a400af1aa4909 (patch) | |
tree | 6aeeaa74374fd4f42f319ab6da9a84eb9ec2ce35 /README | |
parent | 66e0e2b1cd813ca7b857eb998cc5d2838f2c7b18 (diff) |
Convert CONFIG_CONS_INDEX et al to Kconfig
This converts the following to Kconfig:
CONFIG_CONS_INDEX
CONFIG_DEBUG_UART_CLOCK
CONFIG_FSL_TZPC_BP147
CONFIG_GENERIC_ATMEL_MCI
CONFIG_IDENT_STRING
CONFIG_LIBATA
CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE
CONFIG_LPC32XX_GPIO
CONFIG_MP
CONFIG_MPC8XXX_GPIO
CONFIG_MTD_PARTITIONS
CONFIG_MVGBE
CONFIG_MXC_GPIO
CONFIG_NR_DRAM_BANKS
CONFIG_OF_BOARD_SETUP
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_OF_SYSTEM_SETUP
CONFIG_PREBOOT
CONFIG_ROCKCHIP_SERIAL
CONFIG_RTC_ENABLE_32KHZ_OUTPUT
CONFIG_RTC_MV
CONFIG_SCSI_AHCI
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_SPEED
CONFIG_SOFT_SPI
CONFIG_SPI_FLASH_EON
CONFIG_SPI_FLASH_MACRONIX
CONFIG_SPI_FLASH_MTD
CONFIG_SPI_FLASH_SPANSION
CONFIG_SPI_FLASH_SST
CONFIG_SPI_FLASH_STMICRO
CONFIG_SUPPORT_RAW_INITRD
CONFIG_SYS_ARCH_TIMER
CONFIG_SYS_BOARD
CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
CONFIG_SYS_DCACHE_OFF
CONFIG_SYS_FDT_SAVE_ADDRESS
CONFIG_SYS_FLASH_CFI
CONFIG_SYS_FSL_ERRATUM_ESDHC135
CONFIG_SYS_HAS_SERDES
CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_LITTLE_ENDIAN
CONFIG_SYS_LOAD_ADDR
CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
CONFIG_SYS_NS16550
CONFIG_SYS_PLLFIN
CONFIG_SYS_SPI_U_BOOT_OFFS
CONFIG_TIMER_SYS_TICK_CH
CONFIG_USB_EHCI_FSL
CONFIG_U_QE
CONFIG_VERSION_VARIABLE
Signed-off-by: Tom Rini <trini@konsulko.com>
Diffstat (limited to 'README')
-rw-r--r-- | README | 29 |
1 files changed, 0 insertions, 29 deletions
@@ -565,11 +565,6 @@ The following options need to be configured: boards with QUICC Engines require OF_QE to set UCC MAC addresses - CONFIG_OF_BOARD_SETUP - - Board code has addition modification that it wants to make - to the flat device tree before handing it off to the kernel - CONFIG_OF_SYSTEM_SETUP Other code has addition modification that it wants to make @@ -596,9 +591,6 @@ The following options need to be configured: Note: If a "bootargs" environment is defined, it will override the defaults discussed just above. -- Cache Configuration: - CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot - - Cache Configuration for ARM: CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache controller @@ -1520,16 +1512,6 @@ The following options need to be configured: SPI EEPROM, also an instance works with Crystal A/D and D/As on the SACSng board) - CONFIG_SOFT_SPI - - Enables a software (bit-bang) SPI driver rather than - using hardware support. This is a general purpose - driver that only requires three general I/O port pins - (two outputs, one input) to function. If this is - defined, the board configuration must define several - SPI configuration items (port pins to use, etc). For - an example, see include/configs/sacsng.h. - CONFIG_SYS_SPI_MXC_WAIT Timeout for waiting until spi transfer completed. default: (CONFIG_SYS_HZ/100) /* 10 ms */ @@ -1595,13 +1577,6 @@ The following options need to be configured: Time to wait after FPGA configuration. The default is 200 ms. -- Configuration Management: - - CONFIG_IDENT_STRING - - If defined, this string will be added to the U-Boot - version information (U_BOOT_VERSION) - - Vendor Parameter Protection: U-Boot considers the values of the environment @@ -1922,10 +1897,6 @@ The following options need to be configured: CONFIG_SPL_INIT_MINIMAL Arch init code should be built for a very small image - CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION - Partition on the MMC to load U-Boot from when the MMC is being - used in raw mode - CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR Sector to load kernel uImage from when MMC is being used in raw mode (for Falcon mode) |