arm: mvebu: Add Helios4 Armada 38x initial support

The helios4 is built on the SolidRun Armada 38x SOM.
The port os based on the ClearFog board, using information from
https://github.com/helios-4/u-boot-marvell as well as dtb input
from https://github.com/helios-4/linux-marvell

Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>

1 files changed, 314 insertions, 0 deletions

diff --git a/arch/arm/dts/armada-388-helios4.dts b/arch/arm/dts/armada-388-helios4.dts
new file mode 100644
index 00000000000..049d3229647
--- /dev/null
+++ b/arch/arm/dts/armada-388-helios4.dts
@@ -0,0 +1,314 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Helios4
+ * based on SolidRun Clearfog revision A1 rev 2.0 (88F6828)
+ *
+ *  Copyright (C) 2017 Aditya Prayoga <aditya@kobol.io>
+ *
+ */
+
+/dts-v1/;
+#include "armada-388.dtsi"
+#include "armada-38x-solidrun-microsom.dtsi"
+
+/ {
+	model = "Helios4";
+	compatible = "kobol,helios4", "marvell,armada388",
+		"marvell,armada385", "marvell,armada380";
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000>; /* 2 GB */
+	};
+
+	aliases {
+		/* So that mvebu u-boot can update the MAC addresses */
+		ethernet1 = &eth0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_12v: regulator-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "power_brick_12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_12v>;
+	};
+
+	reg_5p0v_hdd: regulator-5v-hdd {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_HDD";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_12v>;
+	};
+
+	reg_5p0v_usb: regulator-5v-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "USB-PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+		enable-active-high;
+		gpio = <&expander0 6 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&reg_12v>;
+	};
+
+	system-leds {
+		compatible = "gpio-leds";
+		status-led {
+			label = "helios4:green:status";
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+		};
+
+		fault-led {
+			label = "helios4:red:fault";
+			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
+			default-state = "keep";
+		};
+	};
+
+	io-leds {
+		compatible = "gpio-leds";
+		sata1-led {
+			label = "helios4:green:ata1";
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata1";
+			default-state = "off";
+		};
+		sata2-led {
+			label = "helios4:green:ata2";
+			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata2";
+			default-state = "off";
+		};
+		sata3-led {
+			label = "helios4:green:ata3";
+			gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata3";
+			default-state = "off";
+		};
+		sata4-led {
+			label = "helios4:green:ata4";
+			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "ata4";
+			default-state = "off";
+		};
+		usb-led {
+			label = "helios4:green:usb";
+			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "usb-host";
+			default-state = "off";
+		};
+	};
+
+	fan1: j10-pwm {
+		compatible = "pwm-fan";
+		pwms = <&gpio1 9 40000>;	/* Target freq:25 kHz */
+	};
+
+	fan2: j17-pwm {
+		compatible = "pwm-fan";
+		pwms = <&gpio1 23 40000>;	/* Target freq:25 kHz */
+	};
+
+	usb2_phy: usb2-phy {
+		compatible = "usb-nop-xceiv";
+		vbus-regulator = <&reg_5p0v_usb>;
+	};
+
+	usb3_phy: usb3-phy {
+		compatible = "usb-nop-xceiv";
+	};
+
+	soc {
+		internal-regs {
+			i2c@11000 {
+				clock-frequency = <400000>;
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+
+				/*
+				 * PCA9655 GPIO expander, up to 1MHz clock.
+				 *  0-Board Revision bit 0 #
+				 *  1-Board Revision bit 1 #
+				 *  5-USB3 overcurrent
+				 *  6-USB3 power
+				 */
+				expander0: gpio-expander@20 {
+					/*
+					 * This is how it should be:
+					 * compatible = "onnn,pca9655",
+					 *	 "nxp,pca9555";
+					 * but you can't do this because of
+					 * the way I2C works.
+					 */
+					compatible = "nxp,pca9555";
+					gpio-controller;
+					#gpio-cells = <2>;
+					reg = <0x20>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pca0_pins>;
+					interrupt-parent = <&gpio0>;
+					interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+
+					board_rev_bit_0 {
+						gpio-hog;
+						gpios = <0 GPIO_ACTIVE_LOW>;
+						input;
+						line-name = "board-rev-0";
+					};
+					board_rev_bit_1 {
+						gpio-hog;
+						gpios = <1 GPIO_ACTIVE_LOW>;
+						input;
+						line-name = "board-rev-1";
+					};
+					usb3_ilimit {
+						gpio-hog;
+						gpios = <5 GPIO_ACTIVE_HIGH>;
+						input;
+						line-name =
+						"usb-overcurrent-status";
+					};
+				};
+
+				temp_sensor: temp@4c {
+					compatible = "ti,lm75";
+					reg = <0x4c>;
+					vcc-supply = <&reg_3p3v>;
+				};
+			};
+
+			i2c@11100 {
+				/*
+				 * External I2C Bus for user peripheral
+				 */
+				clock-frequency = <400000>;
+				pinctrl-0 = <&helios_i2c1_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			sata@a8000 {
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sata0: sata-port@0 {
+					reg = <0>;
+				};
+
+				sata1: sata-port@1 {
+					reg = <1>;
+				};
+			};
+
+			sata@e0000 {
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sata2: sata-port@0 {
+					reg = <0>;
+				};
+
+				sata3: sata-port@1 {
+					reg = <1>;
+				};
+			};
+
+			spi@10680 {
+				pinctrl-0 = <&spi1_pins
+					     &microsom_spi1_cs_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			sdhci@d8000 {
+				bus-width = <4>;
+				cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+				no-1-8-v;
+				pinctrl-0 = <&helios_sdhci_pins
+					     &helios_sdhci_cd_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				vmmc = <&reg_3p3v>;
+				wp-inverted;
+			};
+
+			usb@58000 {
+				usb-phy = <&usb2_phy>;
+				status = "okay";
+			};
+
+			usb3@f0000 {
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				status = "okay";
+			};
+
+			pinctrl@18000 {
+				pca0_pins: pca0-pins {
+					marvell,pins = "mpp23";
+					marvell,function = "gpio";
+				};
+				microsom_phy0_int_pins: microsom-phy0-int-pins {
+					marvell,pins = "mpp18";
+					marvell,function = "gpio";
+				};
+				helios_i2c1_pins: i2c1-pins {
+					marvell,pins = "mpp26", "mpp27";
+					marvell,function = "i2c1";
+				};
+				helios_sdhci_cd_pins: helios-sdhci-cd-pins {
+					marvell,pins = "mpp20";
+					marvell,function = "gpio";
+				};
+				helios_sdhci_pins: helios-sdhci-pins {
+					marvell,pins = "mpp21", "mpp28",
+						       "mpp37", "mpp38",
+						       "mpp39", "mpp40";
+					marvell,function = "sd0";
+				};
+				helios_led_pins: helios-led-pins {
+					marvell,pins = "mpp24", "mpp25",
+						       "mpp49", "mpp50",
+						       "mpp52", "mpp53",
+						       "mpp54";
+					marvell,function = "gpio";
+				};
+				helios_fan_pins: helios-fan-pins {
+					marvell,pins = "mpp41", "mpp43",
+						       "mpp48", "mpp55";
+					marvell,function = "gpio";
+				};
+				microsom_spi1_cs_pins: spi1-cs-pins {
+					marvell,pins = "mpp59";
+					marvell,function = "spi1";
+				};
+			};
+		};
+	};
+};