arm: rpi: Sync rpi dts files from Linux

Sync these files, obtained from Linux v5.15.

This adds a devicetree file for rpi_4 which was not there before.

Testing shows no change so far as I can see:
- boots to U-Boot prompt on rpi0, rpi2
- boots to distro on rpi3
- boots to distro on rpi4

I am assuming that syncing with Linux is safe, but the maintainer should
know for sure.

Signed-off-by: Simon Glass <sjg@chromium.org>

1 files changed, 24 insertions, 200 deletions

diff --git a/arch/arm/dts/bcm283x.dtsi b/arch/arm/dts/bcm283x.dtsi
index 9777644c6c2..a3e06b68094 100644
--- a/arch/arm/dts/bcm283x.dtsi
+++ b/arch/arm/dts/bcm283x.dtsi
@@ -18,7 +18,6 @@
 / {
 	compatible = "brcm,bcm2835";
 	model = "BCM2835";
-	interrupt-parent = <&intc>;
 	#address-cells = <1>;
 	#size-cells = <1>;
 
@@ -31,16 +30,27 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	rmem: reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		cma: linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x4000000>; /* 64MB */
+			reusable;
+			linux,cma-default;
+		};
+	};
+
 	thermal-zones {
 		cpu_thermal: cpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&thermal>;
-
 			trips {
 				cpu-crit {
-					temperature	= <80000>;
+					temperature	= <90000>;
 					hysteresis	= <0>;
 					type		= "critical";
 				};
@@ -56,7 +66,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		timer@7e003000 {
+		system_timer: timer@7e003000 {
 			compatible = "brcm,bcm2835-system-timer";
 			reg = <0x7e003000 0x1000>;
 			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
@@ -67,74 +77,12 @@
 			clock-frequency = <1000000>;
 		};
 
-		txp@7e004000 {
+		txp: txp@7e004000 {
 			compatible = "brcm,bcm2835-txp";
 			reg = <0x7e004000 0x20>;
 			interrupts = <1 11>;
 		};
 
-		dma: dma@7e007000 {
-			compatible = "brcm,bcm2835-dma";
-			reg = <0x7e007000 0xf00>;
-			interrupts = <1 16>,
-				     <1 17>,
-				     <1 18>,
-				     <1 19>,
-				     <1 20>,
-				     <1 21>,
-				     <1 22>,
-				     <1 23>,
-				     <1 24>,
-				     <1 25>,
-				     <1 26>,
-				     /* dma channel 11-14 share one irq */
-				     <1 27>,
-				     <1 27>,
-				     <1 27>,
-				     <1 27>,
-				     /* unused shared irq for all channels */
-				     <1 28>;
-			interrupt-names = "dma0",
-					  "dma1",
-					  "dma2",
-					  "dma3",
-					  "dma4",
-					  "dma5",
-					  "dma6",
-					  "dma7",
-					  "dma8",
-					  "dma9",
-					  "dma10",
-					  "dma11",
-					  "dma12",
-					  "dma13",
-					  "dma14",
-					  "dma-shared-all";
-			#dma-cells = <1>;
-			brcm,dma-channel-mask = <0x7f35>;
-		};
-
-		intc: interrupt-controller@7e00b200 {
-			compatible = "brcm,bcm2835-armctrl-ic";
-			reg = <0x7e00b200 0x200>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-
-		pm: watchdog@7e100000 {
-			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
-			#power-domain-cells = <1>;
-			#reset-cells = <1>;
-			reg = <0x7e100000 0x114>,
-			      <0x7e00a000 0x24>;
-			clocks = <&clocks BCM2835_CLOCK_V3D>,
-				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
-				 <&clocks BCM2835_CLOCK_H264>,
-				 <&clocks BCM2835_CLOCK_ISP>;
-			clock-names = "v3d", "peri_image", "h264", "isp";
-			system-power-controller;
-		};
-
 		clocks: cprman@7e101000 {
 			compatible = "brcm,bcm2835-cprman";
 			#clock-cells = <1>;
@@ -149,12 +97,6 @@
 				<&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
 		};
 
-		rng@7e104000 {
-			compatible = "brcm,bcm2835-rng";
-			reg = <0x7e104000 0x10>;
-			interrupts = <2 29>;
-		};
-
 		mailbox: mailbox@7e00b880 {
 			compatible = "brcm,bcm2835-mbox";
 			reg = <0x7e00b880 0x40>;
@@ -184,8 +126,7 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			/* Defines pin muxing groups according to
-			 * BCM2835-ARM-Peripherals.pdf page 102.
+			/* Defines common pin muxing groups
 			 *
 			 * While each pin can have its mux selected
 			 * for various functions individually, some
@@ -263,15 +204,7 @@
 				brcm,pins = <44 45>;
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
-			i2c_slave_gpio18: i2c_slave_gpio18 {
-				brcm,pins = <18 19 20 21>;
-				brcm,function = <BCM2835_FSEL_ALT3>;
-			};
 
-			jtag_gpio4: jtag_gpio4 {
-				brcm,pins = <4 5 6 12 13>;
-				brcm,function = <BCM2835_FSEL_ALT5>;
-			};
 			jtag_gpio22: jtag_gpio22 {
 				brcm,pins = <22 23 24 25 26 27>;
 				brcm,function = <BCM2835_FSEL_ALT4>;
@@ -286,35 +219,6 @@
 				brcm,function = <BCM2835_FSEL_ALT2>;
 			};
 
-			pwm0_gpio12: pwm0_gpio12 {
-				brcm,pins = <12>;
-				brcm,function = <BCM2835_FSEL_ALT0>;
-			};
-			pwm0_gpio18: pwm0_gpio18 {
-				brcm,pins = <18>;
-				brcm,function = <BCM2835_FSEL_ALT5>;
-			};
-			pwm0_gpio40: pwm0_gpio40 {
-				brcm,pins = <40>;
-				brcm,function = <BCM2835_FSEL_ALT0>;
-			};
-			pwm1_gpio13: pwm1_gpio13 {
-				brcm,pins = <13>;
-				brcm,function = <BCM2835_FSEL_ALT0>;
-			};
-			pwm1_gpio19: pwm1_gpio19 {
-				brcm,pins = <19>;
-				brcm,function = <BCM2835_FSEL_ALT5>;
-			};
-			pwm1_gpio41: pwm1_gpio41 {
-				brcm,pins = <41>;
-				brcm,function = <BCM2835_FSEL_ALT0>;
-			};
-			pwm1_gpio45: pwm1_gpio45 {
-				brcm,pins = <45>;
-				brcm,function = <BCM2835_FSEL_ALT0>;
-			};
-
 			sdhost_gpio48: sdhost_gpio48 {
 				brcm,pins = <48 49 50 51 52 53>;
 				brcm,function = <BCM2835_FSEL_ALT0>;
@@ -396,8 +300,8 @@
 		};
 
 		uart0: serial@7e201000 {
-			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
-			reg = <0x7e201000 0x1000>;
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x7e201000 0x200>;
 			interrupts = <2 25>;
 			clocks = <&clocks BCM2835_CLOCK_UART>,
 				 <&clocks BCM2835_CLOCK_VPU>;
@@ -410,8 +314,6 @@
 			reg = <0x7e202000 0x100>;
 			interrupts = <2 24>;
 			clocks = <&clocks BCM2835_CLOCK_VPU>;
-			dmas = <&dma 13>;
-			dma-names = "rx-tx";
 			status = "disabled";
 		};
 
@@ -419,16 +321,12 @@
 			compatible = "brcm,bcm2835-i2s";
 			reg = <0x7e203000 0x24>;
 			clocks = <&clocks BCM2835_CLOCK_PCM>;
-
-			dmas = <&dma 2>,
-			       <&dma 3>;
-			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
 		spi: spi@7e204000 {
 			compatible = "brcm,bcm2835-spi";
-			reg = <0x7e204000 0x1000>;
+			reg = <0x7e204000 0x200>;
 			interrupts = <2 22>;
 			clocks = <&clocks BCM2835_CLOCK_VPU>;
 			#address-cells = <1>;
@@ -438,7 +336,7 @@
 
 		i2c0: i2c@7e205000 {
 			compatible = "brcm,bcm2835-i2c";
-			reg = <0x7e205000 0x1000>;
+			reg = <0x7e205000 0x200>;
 			interrupts = <2 21>;
 			clocks = <&clocks BCM2835_CLOCK_VPU>;
 			#address-cells = <1>;
@@ -446,18 +344,6 @@
 			status = "disabled";
 		};
 
-		pixelvalve@7e206000 {
-			compatible = "brcm,bcm2835-pixelvalve0";
-			reg = <0x7e206000 0x100>;
-			interrupts = <2 13>; /* pwa0 */
-		};
-
-		pixelvalve@7e207000 {
-			compatible = "brcm,bcm2835-pixelvalve1";
-			reg = <0x7e207000 0x100>;
-			interrupts = <2 14>; /* pwa1 */
-		};
-
 		dpi: dpi@7e208000 {
 			compatible = "brcm,bcm2835-dpi";
 			reg = <0x7e208000 0x8c>;
@@ -486,13 +372,6 @@
 					     "dsi0_ddr2",
 					     "dsi0_ddr";
 
-		};
-
-		thermal: thermal@7e212000 {
-			compatible = "brcm,bcm2835-thermal";
-			reg = <0x7e212000 0x8>;
-			clocks = <&clocks BCM2835_CLOCK_TSENS>;
-			#thermal-sensor-cells = <0>;
 			status = "disabled";
 		};
 
@@ -541,7 +420,7 @@
 			status = "disabled";
 		};
 
-		sdhci: sdhci@7e300000 {
+		sdhci: mmc@7e300000 {
 			compatible = "brcm,bcm2835-sdhci";
 			reg = <0x7e300000 0x100>;
 			interrupts = <2 30>;
@@ -585,44 +464,6 @@
 			status = "disabled";
 		};
 
-		i2c2: i2c@7e805000 {
-			compatible = "brcm,bcm2835-i2c";
-			reg = <0x7e805000 0x1000>;
-			interrupts = <2 21>;
-			clocks = <&clocks BCM2835_CLOCK_VPU>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-			status = "disabled";
-		};
-
-		vec: vec@7e806000 {
-			compatible = "brcm,bcm2835-vec";
-			reg = <0x7e806000 0x1000>;
-			clocks = <&clocks BCM2835_CLOCK_VEC>;
-			interrupts = <2 27>;
-			status = "disabled";
-		};
-
-		pixelvalve@7e807000 {
-			compatible = "brcm,bcm2835-pixelvalve2";
-			reg = <0x7e807000 0x100>;
-			interrupts = <2 10>; /* pixelvalve */
-		};
-
-		hdmi: hdmi@7e902000 {
-			compatible = "brcm,bcm2835-hdmi";
-			reg = <0x7e902000 0x600>,
-			      <0x7e808000 0x100>;
-			interrupts = <2 8>, <2 9>;
-			ddc = <&i2c2>;
-			clocks = <&clocks BCM2835_PLLH_PIX>,
-				 <&clocks BCM2835_CLOCK_HSM>;
-			clock-names = "pixel", "hdmi";
-			dmas = <&dma 17>;
-			dma-names = "audio-rx";
-			status = "disabled";
-		};
-
 		usb: usb@7e980000 {
 			compatible = "brcm,bcm2835-usb";
 			reg = <0x7e980000 0x10000>;
@@ -634,36 +475,19 @@
 			phys = <&usbphy>;
 			phy-names = "usb2-phy";
 		};
-
-		v3d: v3d@7ec00000 {
-			compatible = "brcm,bcm2835-v3d";
-			reg = <0x7ec00000 0x1000>;
-			interrupts = <1 10>;
-			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
-		};
-
-		vc4: gpu {
-			compatible = "brcm,bcm2835-vc4";
-		};
 	};
 
 	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		/* The oscillator is the root of the clock tree. */
-		clk_osc: clock@3 {
+		clk_osc: clk-osc {
 			compatible = "fixed-clock";
-			reg = <3>;
 			#clock-cells = <0>;
 			clock-output-names = "osc";
 			clock-frequency = <19200000>;
 		};
 
-		clk_usb: clock@4 {
+		clk_usb: clk-usb {
 			compatible = "fixed-clock";
-			reg = <4>;
 			#clock-cells = <0>;
 			clock-output-names = "otg";
 			clock-frequency = <480000000>;