ARM: dts: sunxi: A13/A31/A23/A33: Sync from Linux v5.18-rc1

Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.

These changes are combined into one commit due to interdependencies:
 - The unit addresses were removed from bitbanged I2C buses, which
   drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
   and sun6i-a31-colombus.dts.
 - The pinctrl nodes were renamed, including some used by the shared
   header sunxi-reference-design-tablet.dtsi.

To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.

This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.

This commit also adds the following new board devicetrees:
 - sun5i-a13-licheepi-one.dts
 - sun5i-a13-pocketbook-touch-lux-3.dts
 - sun5i-gr8-evb.dts
 - sun8i-a23-ippo-q8h-v1.2.dts
 - sun8i-a23-ippo-q8h-v5.dts
 - sun8i-a33-et-q8-v1.6.dts
 - sun8i-a33-ippo-q8h-v1.2.dts
 - sun8i-r16-nintendo-super-nes-classic.dts

As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.

Signed-off-by: Samuel Holland <samuel@sholland.org>

1 files changed, 3 insertions, 19 deletions

diff --git a/arch/arm/dts/sun5i-a10s-r7-tv-dongle.dts b/arch/arm/dts/sun5i-a10s-r7-tv-dongle.dts
index 034853d1c08..964360f0610 100644
--- a/arch/arm/dts/sun5i-a10s-r7-tv-dongle.dts
+++ b/arch/arm/dts/sun5i-a10s-r7-tv-dongle.dts
@@ -63,7 +63,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pins_r7>;
 
-		green {
+		led {
 			label = "r7-tv-dongle:green:usr";
 			gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -76,8 +76,6 @@
 };
 
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_r7>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
@@ -85,8 +83,6 @@
 };
 
 &mmc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc1_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	non-removable;
@@ -98,33 +94,21 @@
 };
 
 &pio {
-	mmc0_cd_pin_r7: mmc0_cd_pin@0 {
-		pins = "PG1";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	led_pins_r7: led_pins@0 {
+	led_pins_r7: led-pin {
 		pins = "PB2";
 		function = "gpio_out";
 		drive-strength = <20>;
 	};
-
-	usb1_vbus_pin_r7: usb1_vbus_pin@0 {
-		pins = "PG13";
-		function = "gpio_out";
-	};
 };
 
 &reg_usb1_vbus {
-	pinctrl-0 = <&usb1_vbus_pin_r7>;
 	gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_pb_pins>;
 	status = "okay";
 };