ARM: dts: sunxi: A13/A31/A23/A33: Sync from Linux v5.18-rc1

Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.

These changes are combined into one commit due to interdependencies:
 - The unit addresses were removed from bitbanged I2C buses, which
   drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
   and sun6i-a31-colombus.dts.
 - The pinctrl nodes were renamed, including some used by the shared
   header sunxi-reference-design-tablet.dtsi.

To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.

This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.

This commit also adds the following new board devicetrees:
 - sun5i-a13-licheepi-one.dts
 - sun5i-a13-pocketbook-touch-lux-3.dts
 - sun5i-gr8-evb.dts
 - sun8i-a23-ippo-q8h-v1.2.dts
 - sun8i-a23-ippo-q8h-v5.dts
 - sun8i-a33-et-q8-v1.6.dts
 - sun8i-a33-ippo-q8h-v1.2.dts
 - sun8i-r16-nintendo-super-nes-classic.dts

As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.

Signed-off-by: Samuel Holland <samuel@sholland.org>

1 files changed, 12 insertions, 34 deletions

diff --git a/arch/arm/dts/sun6i-a31-m9.dts b/arch/arm/dts/sun6i-a31-m9.dts
index 9698f6d38d0..e4f3415e610 100644
--- a/arch/arm/dts/sun6i-a31-m9.dts
+++ b/arch/arm/dts/sun6i-a31-m9.dts
@@ -60,10 +60,8 @@
 
 	leds {
 		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&led_pins_m9>;
 
-		blue {
+		led {
 			label = "m9:blue:pwr";
 			gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
@@ -85,26 +83,26 @@
 
 &gmac {
 	pinctrl-names = "default";
-	pinctrl-0 = <&gmac_pins_mii_a>;
-	phy = <&phy1>;
+	pinctrl-0 = <&gmac_mii_pins>;
+	phy-handle = <&phy1>;
 	phy-mode = "mii";
 	phy-supply = <&reg_dldo1>;
 	status = "okay";
-
-	phy1: ethernet-phy@1 {
-		reg = <1>;
-	};
 };
 
 &ir {
 	pinctrl-names = "default";
-	pinctrl-0 = <&ir_pins_a>;
+	pinctrl-0 = <&s_ir_rx_pin>;
 	status = "okay";
 };
 
+&mdio {
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+};
+
 &mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_m9>;
 	vmmc-supply = <&reg_dcdc1>;
 	bus-width = <4>;
 	cd-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 */
@@ -117,31 +115,13 @@
 	axp22x: pmic@68 {
 		compatible = "x-powers,axp221";
 		reg = <0x68>;
-		interrupt-parent = <&nmi_intc>;
+		interrupt-parent = <&r_intc>;
 		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 	};
 };
 
 #include "axp22x.dtsi"
 
-&pio {
-	led_pins_m9: led_pins@0 {
-		pins = "PH13";
-		function = "gpio_out";
-	};
-
-	mmc0_cd_pin_m9: mmc0_cd_pin@0 {
-		pins = "PH22";
-		function = "gpio_in";
-		bias-pull-up;
-	};
-
-	usb1_vbus_pin_m9: usb1_vbus_pin@0 {
-		pins = "PC27";
-		function = "gpio_out";
-	};
-};
-
 &reg_aldo1 {
 	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
@@ -215,15 +195,13 @@
 };
 
 &reg_usb1_vbus {
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_vbus_pin_m9>;
 	gpio = <&pio 2 27 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &uart0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
+	pinctrl-0 = <&uart0_ph_pins>;
 	status = "okay";
 };