rockchip: rk3328: Add support for Orange Pi R1 Plus

Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.

This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.

The device tree and description are taken from kernel v6.3-rc1.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>

3 files changed, 420 insertions, 0 deletions

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index b7780de776b..0cd2c86fdb5 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -125,6 +125,7 @@ dtb-$(CONFIG_ROCKCHIP_RK3328) += \
 	rk3328-evb.dtb \
 	rk3328-nanopi-r2c.dtb \
 	rk3328-nanopi-r2s.dtb \
+	rk3328-orangepi-r1-plus.dtb \
 	rk3328-roc-cc.dtb \
 	rk3328-rock64.dtb \
 	rk3328-rock-pi-e.dtb
diff --git a/arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi b/arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi
new file mode 100644
index 00000000000..637c70adf19
--- /dev/null
+++ b/arch/arm/dts/rk3328-orangepi-r1-plus-u-boot.dtsi
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * (C) Copyright 2018-2019 Rockchip Electronics Co., Ltd
+ * (C) Copyright 2020 David Bauer
+ */
+
+#include "rk3328-u-boot.dtsi"
+#include "rk3328-sdram-ddr4-666.dtsi"
+/ {
+	chosen {
+		u-boot,spl-boot-order = "same-as-spl", &sdmmc, &emmc;
+	};
+};
+
+&gpio0 {
+	bootph-pre-ram;
+};
+
+&pinctrl {
+	bootph-pre-ram;
+};
+
+&sdmmc0m1_pin {
+	bootph-pre-ram;
+};
+
+&pcfg_pull_up_4ma {
+	bootph-pre-ram;
+};
+
+/* Need this and all the pinctrl/gpio stuff above to set pinmux */
+&vcc_sd {
+	bootph-pre-ram;
+};
+
+&gmac2io {
+	snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+};
+
+&spi0 {
+	spi_flash: spiflash@0 {
+		bootph-all;
+	};
+};
diff --git a/arch/arm/dts/rk3328-orangepi-r1-plus.dts b/arch/arm/dts/rk3328-orangepi-r1-plus.dts
new file mode 100644
index 00000000000..dc83d74045a
--- /dev/null
+++ b/arch/arm/dts/rk3328-orangepi-r1-plus.dts
@@ -0,0 +1,373 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Based on rk3328-nanopi-r2s.dts, which is:
+ *   Copyright (c) 2020 David Bauer <mail@david-bauer.net>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "rk3328.dtsi"
+
+/ {
+	model = "Xunlong Orange Pi R1 Plus";
+	compatible = "xunlong,orangepi-r1-plus", "rockchip,rk3328";
+
+	aliases {
+		ethernet1 = &rtl8153;
+		mmc0 = &sdmmc;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac_clk: gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac_clkin";
+		#clock-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
+		pinctrl-names = "default";
+
+		led-0 {
+			function = LED_FUNCTION_LAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	vcc_sd: sdmmc-regulator {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+		pinctrl-0 = <&sdmmc0m1_pin>;
+		pinctrl-names = "default";
+		regulator-name = "vcc_sd";
+		regulator-boot-on;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_sys: vcc-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vdd_5v_lan: vdd-5v-lan-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&lan_vdd_pin>;
+		pinctrl-names = "default";
+		regulator-name = "vdd_5v_lan";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc_sys>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_arm>;
+};
+
+&display_subsystem {
+	status = "disabled";
+};
+
+&gmac2io {
+	assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+	assigned-clock-parents = <&gmac_clk>, <&gmac_clk>;
+	clock_in_out = "input";
+	phy-handle = <&rtl8211e>;
+	phy-mode = "rgmii";
+	phy-supply = <&vcc_io>;
+	pinctrl-0 = <&rgmiim1_pins>;
+	pinctrl-names = "default";
+	snps,aal;
+	rx_delay = <0x18>;
+	tx_delay = <0x24>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtl8211e: ethernet-phy@1 {
+			reg = <1>;
+			pinctrl-0 = <&eth_phy_reset_pin>;
+			pinctrl-names = "default";
+			reset-assert-us = <10000>;
+			reset-deassert-us = <50000>;
+			reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	rk805: pmic@18 {
+		compatible = "rockchip,rk805";
+		reg = <0x18>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk805-clkout2";
+		gpio-controller;
+		#gpio-cells = <2>;
+		pinctrl-0 = <&pmic_int_l>;
+		pinctrl-names = "default";
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_io>;
+		vcc6-supply = <&vcc_sys>;
+
+		regulators {
+			vdd_log: DCDC_REG1 {
+				regulator-name = "vdd_log";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <712500>;
+				regulator-max-microvolt = <1450000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+
+			vdd_arm: DCDC_REG2 {
+				regulator-name = "vdd_arm";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <712500>;
+				regulator-max-microvolt = <1450000>;
+				regulator-ramp-delay = <12500>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <950000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_io: DCDC_REG4 {
+				regulator-name = "vcc_io";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_18: LDO_REG1 {
+				regulator-name = "vcc_18";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc18_emmc: LDO_REG2 {
+				regulator-name = "vcc18_emmc";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_10: LDO_REG3 {
+				regulator-name = "vdd_10";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1000000>;
+				};
+			};
+		};
+	};
+};
+
+&io_domains {
+	pmuio-supply = <&vcc_io>;
+	vccio1-supply = <&vcc_io>;
+	vccio2-supply = <&vcc18_emmc>;
+	vccio3-supply = <&vcc_io>;
+	vccio4-supply = <&vcc_io>;
+	vccio5-supply = <&vcc_io>;
+	vccio6-supply = <&vcc_io>;
+	status = "okay";
+};
+
+&pinctrl {
+	gmac2io {
+		eth_phy_reset_pin: eth-phy-reset-pin {
+			rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	leds {
+		lan_led_pin: lan-led-pin {
+			rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		sys_led_pin: sys-led-pin {
+			rockchip,pins = <3 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		wan_led_pin: wan-led-pin {
+			rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	lan {
+		lan_vdd_pin: lan-vdd-pin {
+			rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	disable-wp;
+	pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vcc_sd>;
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <0>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&u2phy {
+	status = "okay";
+};
+
+&u2phy_host {
+	status = "okay";
+};
+
+&u2phy_otg {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb20_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbdrd3 {
+	dr_mode = "host";
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* Second port is for USB 3.0 */
+	rtl8153: device@2 {
+		compatible = "usbbda,8153";
+		reg = <2>;
+	};
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};