ARM: dts: renesas: Remove leftovers after OF_UPSTREAM conversion

Remove leftover DTSI files after OF_UPSTREAM conversion.
Those are no longer used and no longer necessary, remove them.
No functional change.

Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Acked-by: Adam Ford <aford173@gmail.com>

6 files changed, 0 insertions, 1838 deletions

diff --git a/arch/arm/dts/salvator-common.dtsi b/arch/arm/dts/salvator-common.dtsi
deleted file mode 100644
index 4a3d5037821..00000000000
--- a/arch/arm/dts/salvator-common.dtsi
+++ /dev/null
@@ -1,1104 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree Source for common parts of Salvator-X board variants
- *
- * Copyright (C) 2015-2016 Renesas Electronics Corp.
- */
-
-/*
- * SSI-AK4613
- *
- * This command is required when Playback/Capture
- *
- *	amixer set "DVC Out" 100%
- *	amixer set "DVC In" 100%
- *
- * You can use Mute
- *
- *	amixer set "DVC Out Mute" on
- *	amixer set "DVC In Mute" on
- *
- * You can use Volume Ramp
- *
- *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
- *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
- *	amixer set "DVC Out Ramp" on
- *	aplay xxx.wav &
- *	amixer set "DVC Out"  80%  // Volume Down
- *	amixer set "DVC Out" 100%  // Volume Up
- */
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-		i2c5 = &i2c5;
-		i2c6 = &i2c6;
-		i2c7 = &i2c_dvfs;
-		serial0 = &scif2;
-		serial1 = &hscif1;
-		ethernet0 = &avb;
-		mmc0 = &sdhi2;
-		mmc1 = &sdhi0;
-		mmc2 = &sdhi3;
-	};
-
-	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
-		stdout-path = "serial0:115200n8";
-	};
-
-	audio_clkout: audio-clkout {
-		/*
-		 * This is same as <&rcar_sound 0>
-		 * but needed to avoid cs2000/rcar_sound probe dead-lock
-		 */
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <12288000>;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 50000>;
-
-		brightness-levels = <256 128 64 16 8 4 0>;
-		default-brightness-level = <6>;
-
-		power-supply = <&reg_12v>;
-		enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
-	};
-
-	cvbs-in {
-		compatible = "composite-video-connector";
-		label = "CVBS IN";
-
-		port {
-			cvbs_con: endpoint {
-				remote-endpoint = <&adv7482_ain7>;
-			};
-		};
-	};
-
-	hdmi-in {
-		compatible = "hdmi-connector";
-		label = "HDMI IN";
-		type = "a";
-
-		port {
-			hdmi_in_con: endpoint {
-				remote-endpoint = <&adv7482_hdmi>;
-			};
-		};
-	};
-
-	hdmi0-out {
-		compatible = "hdmi-connector";
-		label = "HDMI0 OUT";
-		type = "a";
-
-		port {
-			hdmi0_con: endpoint {
-				remote-endpoint = <&rcar_dw_hdmi0_out>;
-			};
-		};
-	};
-
-	hdmi1-out {
-		compatible = "hdmi-connector";
-		label = "HDMI1 OUT";
-		type = "a";
-
-		port {
-			hdmi1_con: endpoint {
-			};
-		};
-	};
-
-	keys {
-		compatible = "gpio-keys";
-
-		pinctrl-0 = <&keys_pins>;
-		pinctrl-names = "default";
-
-		key-1 {
-			gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_1>;
-			label = "SW4-1";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-2 {
-			gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_2>;
-			label = "SW4-2";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-3 {
-			gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_3>;
-			label = "SW4-3";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-4 {
-			gpios = <&gpio5 23 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_4>;
-			label = "SW4-4";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-a {
-			gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_A>;
-			label = "TSW0";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-b {
-			gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_B>;
-			label = "TSW1";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-		key-c {
-			gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_C>;
-			label = "TSW2";
-			wakeup-source;
-			debounce-interval = <20>;
-		};
-	};
-
-	reg_1p8v: regulator-1p8v {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_12v: regulator-12v {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-12V";
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	sound_card: sound {
-		compatible = "audio-graph-card";
-
-		label = "rcar-sound";
-
-		dais = <&rsnd_port0	/* ak4613 */
-			&rsnd_port1	/* HDMI0  */
-#ifdef SOC_HAS_HDMI1
-			&rsnd_port2	/* HDMI1  */
-#endif
-			>;
-	};
-
-	vbus0_usb2: regulator-vbus0-usb2 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "USB20_VBUS0";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-
-		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vcc_sdhi0: regulator-vcc-sdhi0 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI0 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi0: regulator-vccq-sdhi0 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI0 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1>, <1800000 0>;
-	};
-
-	vcc_sdhi3: regulator-vcc-sdhi3 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI3 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi3: regulator-vccq-sdhi3 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI3 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1>, <1800000 0>;
-	};
-
-	vga {
-		compatible = "vga-connector";
-
-		port {
-			vga_in: endpoint {
-				remote-endpoint = <&adv7123_out>;
-			};
-		};
-	};
-
-	vga-encoder {
-		compatible = "adi,adv7123";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7123_in: endpoint {
-					remote-endpoint = <&du_out_rgb>;
-				};
-			};
-			port@1 {
-				reg = <1>;
-				adv7123_out: endpoint {
-					remote-endpoint = <&vga_in>;
-				};
-			};
-		};
-	};
-
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
-	};
-
-	/* External DU dot clocks */
-	x21_clk: x21-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <33000000>;
-	};
-
-	x22_clk: x22-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <33000000>;
-	};
-
-	x23_clk: x23-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <25000000>;
-	};
-};
-
-&a57_0 {
-	cpu-supply = <&dvfs>;
-};
-
-&audio_clk_a {
-	clock-frequency = <22579200>;
-};
-
-&avb {
-	pinctrl-0 = <&avb_pins>;
-	pinctrl-names = "default";
-	phy-handle = <&phy0>;
-	tx-internal-delay-ps = <2000>;
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		compatible = "ethernet-phy-id0022.1622",
-			     "ethernet-phy-ieee802.3-c22";
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
-	};
-};
-
-&csi20 {
-	status = "okay";
-
-	ports {
-		port@0 {
-			csi20_in: endpoint {
-				clock-lanes = <0>;
-				data-lanes = <1>;
-				remote-endpoint = <&adv7482_txb>;
-			};
-		};
-	};
-};
-
-&csi40 {
-	status = "okay";
-
-	ports {
-		port@0 {
-			csi40_in: endpoint {
-				clock-lanes = <0>;
-				data-lanes = <1 2 3 4>;
-				remote-endpoint = <&adv7482_txa>;
-			};
-		};
-	};
-};
-
-&du {
-	pinctrl-0 = <&du_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	ports {
-		port@0 {
-			du_out_rgb: endpoint {
-				remote-endpoint = <&adv7123_in>;
-			};
-		};
-	};
-};
-
-&ehci0 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-&extalr_clk {
-	clock-frequency = <32768>;
-};
-
-&hdmi0 {
-	status = "okay";
-
-	ports {
-		port@1 {
-			reg = <1>;
-			rcar_dw_hdmi0_out: endpoint {
-				remote-endpoint = <&hdmi0_con>;
-			};
-		};
-		port@2 {
-			reg = <2>;
-			dw_hdmi0_snd_in: endpoint {
-				remote-endpoint = <&rsnd_endpoint1>;
-			};
-		};
-	};
-};
-
-#ifdef SOC_HAS_HDMI1
-&hdmi1 {
-	status = "okay";
-
-	ports {
-		port@1 {
-			reg = <1>;
-			rcar_dw_hdmi1_out: endpoint {
-				remote-endpoint = <&hdmi1_con>;
-			};
-		};
-		port@2 {
-			reg = <2>;
-			dw_hdmi1_snd_in: endpoint {
-				remote-endpoint = <&rsnd_endpoint2>;
-			};
-		};
-	};
-};
-
-&hdmi1_con {
-	remote-endpoint = <&rcar_dw_hdmi1_out>;
-};
-#endif /* SOC_HAS_HDMI1 */
-
-&hscif1 {
-	pinctrl-0 = <&hscif1_pins>;
-	pinctrl-names = "default";
-
-	uart-has-rtscts;
-	/* Please only enable hscif1 or scif1 */
-	status = "okay";
-};
-
-&hsusb {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&i2c2 {
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-
-	clock-frequency = <100000>;
-
-	ak4613: codec@10 {
-		compatible = "asahi-kasei,ak4613";
-		#sound-dai-cells = <0>;
-		reg = <0x10>;
-		clocks = <&rcar_sound 3>;
-
-		asahi-kasei,in1-single-end;
-		asahi-kasei,in2-single-end;
-		asahi-kasei,out1-single-end;
-		asahi-kasei,out2-single-end;
-		asahi-kasei,out3-single-end;
-		asahi-kasei,out4-single-end;
-		asahi-kasei,out5-single-end;
-		asahi-kasei,out6-single-end;
-
-		port {
-			ak4613_endpoint: endpoint {
-				remote-endpoint = <&rsnd_endpoint0>;
-			};
-		};
-	};
-
-	cs2000: clk_multiplier@4f {
-		#clock-cells = <0>;
-		compatible = "cirrus,cs2000-cp";
-		reg = <0x4f>;
-		clocks = <&audio_clkout>, <&x12_clk>;
-		clock-names = "clk_in", "ref_clk";
-
-		assigned-clocks = <&cs2000>;
-		assigned-clock-rates = <24576000>; /* 1/1 divide */
-	};
-};
-
-&i2c4 {
-	status = "okay";
-
-	pca9654: gpio@20 {
-		compatible = "onnn,pca9654";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	video-receiver@70 {
-		compatible = "adi,adv7482";
-		reg = <0x70 0x71 0x72 0x73 0x74 0x75
-		       0x60 0x61 0x62 0x63 0x64 0x65>;
-		reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
-			    "infoframe", "cbus", "cec", "sdp", "txa", "txb" ;
-
-		interrupt-parent = <&gpio6>;
-		interrupt-names = "intrq1", "intrq2";
-		interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
-			     <31 IRQ_TYPE_LEVEL_LOW>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@7 {
-				reg = <7>;
-
-				adv7482_ain7: endpoint {
-					remote-endpoint = <&cvbs_con>;
-				};
-			};
-
-			port@8 {
-				reg = <8>;
-
-				adv7482_hdmi: endpoint {
-					remote-endpoint = <&hdmi_in_con>;
-				};
-			};
-
-			port@a {
-				reg = <10>;
-
-				adv7482_txa: endpoint {
-					clock-lanes = <0>;
-					data-lanes = <1 2 3 4>;
-					remote-endpoint = <&csi40_in>;
-				};
-			};
-
-			port@b {
-				reg = <11>;
-
-				adv7482_txb: endpoint {
-					clock-lanes = <0>;
-					data-lanes = <1>;
-					remote-endpoint = <&csi20_in>;
-				};
-			};
-		};
-	};
-
-	csa_vdd: adc@7c {
-		compatible = "maxim,max9611";
-		reg = <0x7c>;
-
-		shunt-resistor-micro-ohms = <5000>;
-	};
-
-	csa_dvfs: adc@7f {
-		compatible = "maxim,max9611";
-		reg = <0x7f>;
-
-		shunt-resistor-micro-ohms = <5000>;
-	};
-};
-
-&i2c_dvfs {
-	status = "okay";
-
-	clock-frequency = <400000>;
-
-	pmic: pmic@30 {
-		pinctrl-0 = <&irq0_pins>;
-		pinctrl-names = "default";
-
-		compatible = "rohm,bd9571mwv";
-		reg = <0x30>;
-		interrupt-parent = <&intc_ex>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		rohm,ddr-backup-power = <0xf>;
-		rohm,rstbmode-level;
-
-		regulators {
-			dvfs: dvfs {
-				regulator-name = "dvfs";
-				regulator-min-microvolt = <750000>;
-				regulator-max-microvolt = <1030000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-		};
-	};
-
-	eeprom@50 {
-		compatible = "rohm,br24t01", "atmel,24c01";
-		reg = <0x50>;
-		pagesize = <8>;
-	};
-};
-
-&ohci0 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
-};
-
-&pcie_bus_clk {
-	clock-frequency = <100000000>;
-};
-
-&pciec0 {
-	status = "okay";
-};
-
-&pciec1 {
-	status = "okay";
-};
-
-&pfc {
-	pinctrl-0 = <&scif_clk_pins>;
-	pinctrl-names = "default";
-
-	avb_pins: avb {
-		mux {
-			groups = "avb_link", "avb_mdio", "avb_mii";
-			function = "avb";
-		};
-
-		pins_mdio {
-			groups = "avb_mdio";
-			drive-strength = <24>;
-		};
-
-		pins_mii_tx {
-			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
-			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
-			drive-strength = <12>;
-		};
-	};
-
-	du_pins: du {
-		groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
-		function = "du";
-	};
-
-	hscif1_pins: hscif1 {
-		groups = "hscif1_data_a", "hscif1_ctrl_a";
-		function = "hscif1";
-	};
-
-	i2c2_pins: i2c2 {
-		groups = "i2c2_a";
-		function = "i2c2";
-	};
-
-	irq0_pins: irq0 {
-		groups = "intc_ex_irq0";
-		function = "intc_ex";
-	};
-
-	keys_pins: keys {
-		pins = "GP_5_17", "GP_5_20", "GP_5_22";
-		bias-pull-up;
-	};
-
-	pwm1_pins: pwm1 {
-		groups = "pwm1_a";
-		function = "pwm1";
-	};
-
-	scif1_pins: scif1 {
-		groups = "scif1_data_a", "scif1_ctrl";
-		function = "scif1";
-	};
-
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
-	};
-
-	scif_clk_pins: scif_clk {
-		groups = "scif_clk_a";
-		function = "scif_clk";
-	};
-
-	sdhi0_pins: sd0 {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <3300>;
-	};
-
-	sdhi0_pins_uhs: sd0_uhs {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <1800>;
-	};
-
-	sdhi2_pins: sd2 {
-		groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
-		function = "sdhi2";
-		power-source = <1800>;
-	};
-
-	sdhi3_pins: sd3 {
-		groups = "sdhi3_data4", "sdhi3_ctrl";
-		function = "sdhi3";
-		power-source = <3300>;
-	};
-
-	sdhi3_pins_uhs: sd3_uhs {
-		groups = "sdhi3_data4", "sdhi3_ctrl";
-		function = "sdhi3";
-		power-source = <1800>;
-	};
-
-	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
-		function = "ssi";
-	};
-
-	sound_clk_pins: sound_clk {
-		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
-			 "audio_clkout_a", "audio_clkout3_a";
-		function = "audio_clk";
-	};
-
-	usb0_pins: usb0 {
-		groups = "usb0";
-		function = "usb0";
-	};
-
-	usb1_pins: usb1 {
-		mux {
-			groups = "usb1";
-			function = "usb1";
-		};
-
-		ovc {
-			pins = "GP_6_27";
-			bias-pull-up;
-		};
-
-		pwen {
-			pins = "GP_6_26";
-			bias-pull-down;
-		};
-	};
-
-	usb30_pins: usb30 {
-		groups = "usb30";
-		function = "usb30";
-	};
-};
-
-&pwm1 {
-	pinctrl-0 = <&pwm1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&rcar_sound {
-	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
-	pinctrl-names = "default";
-
-	/* audio_clkout0/1/2/3 */
-	#clock-cells = <1>;
-	clock-frequency = <12288000 11289600>;
-
-	status = "okay";
-
-	/* update <audio_clk_b> to <cs2000> */
-	clocks = <&cpg CPG_MOD 1005>,
-		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
-		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
-		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
-		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
-		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
-		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
-		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
-		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
-		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
-		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
-		 <&audio_clk_a>, <&cs2000>,
-		 <&audio_clk_c>,
-		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
-
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		rsnd_port0: port@0 {
-			reg = <0>;
-			rsnd_endpoint0: endpoint {
-				remote-endpoint = <&ak4613_endpoint>;
-
-				dai-format = "left_j";
-				bitclock-master = <&rsnd_endpoint0>;
-				frame-master = <&rsnd_endpoint0>;
-
-				playback = <&ssi0>, <&src0>, <&dvc0>;
-				capture = <&ssi1>, <&src1>, <&dvc1>;
-			};
-		};
-
-		rsnd_port1: port@1 {
-			reg = <1>;
-			rsnd_endpoint1: endpoint {
-				remote-endpoint = <&dw_hdmi0_snd_in>;
-
-				dai-format = "i2s";
-				bitclock-master = <&rsnd_endpoint1>;
-				frame-master = <&rsnd_endpoint1>;
-
-				playback = <&ssi2>;
-			};
-		};
-
-#ifdef SOC_HAS_HDMI1
-		rsnd_port2: port@2 {
-			reg = <2>;
-			rsnd_endpoint2: endpoint {
-				remote-endpoint = <&dw_hdmi1_snd_in>;
-
-				dai-format = "i2s";
-				bitclock-master = <&rsnd_endpoint2>;
-				frame-master = <&rsnd_endpoint2>;
-
-				playback = <&ssi3>;
-			};
-		};
-#endif /* SOC_HAS_HDMI1 */
-	};
-};
-
-&rpc {
-	/* Left disabled.  To be enabled by firmware when unlocked. */
-
-	flash@0 {
-		compatible = "cypress,hyperflash", "cfi-flash";
-		reg = <0>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			bootparam@0 {
-				reg = <0x00000000 0x040000>;
-				read-only;
-			};
-			bl2@40000 {
-				reg = <0x00040000 0x140000>;
-				read-only;
-			};
-			cert_header_sa6@180000 {
-				reg = <0x00180000 0x040000>;
-				read-only;
-			};
-			bl31@1c0000 {
-				reg = <0x001c0000 0x040000>;
-				read-only;
-			};
-			tee@200000 {
-				reg = <0x00200000 0x440000>;
-				read-only;
-			};
-			uboot@640000 {
-				reg = <0x00640000 0x100000>;
-				read-only;
-			};
-			dtb@740000 {
-				reg = <0x00740000 0x080000>;
-			};
-			kernel@7c0000 {
-				reg = <0x007c0000 0x1400000>;
-			};
-			user@1bc0000 {
-				reg = <0x01bc0000 0x2440000>;
-			};
-		};
-	};
-};
-
-&rwdt {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-#ifdef SOC_HAS_SATA
-&sata {
-	status = "okay";
-};
-#endif /* SOC_HAS_SATA */
-
-&scif1 {
-	pinctrl-0 = <&scif1_pins>;
-	pinctrl-names = "default";
-
-	uart-has-rtscts;
-	/* Please only enable hscif1 or scif1 */
-	/* status = "okay"; */
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&scif_clk {
-	clock-frequency = <14745600>;
-};
-
-&sdhi0 {
-	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-1 = <&sdhi0_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi0>;
-	vqmmc-supply = <&vccq_sdhi0>;
-	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-	status = "okay";
-};
-
-&sdhi2 {
-	/* used for on-board 8bit eMMC */
-	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-1 = <&sdhi2_pins>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	bus-width = <8>;
-	mmc-hs200-1_8v;
-	mmc-hs400-1_8v;
-	no-sd;
-	no-sdio;
-	non-removable;
-	fixed-emmc-driver-type = <1>;
-	full-pwr-cycle-in-suspend;
-	status = "okay";
-};
-
-&sdhi3 {
-	pinctrl-0 = <&sdhi3_pins>;
-	pinctrl-1 = <&sdhi3_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi3>;
-	vqmmc-supply = <&vccq_sdhi3>;
-	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-	status = "okay";
-};
-
-&ssi1 {
-	shared-pin;
-};
-
-&usb_extal_clk {
-	clock-frequency = <50000000>;
-};
-
-&usb2_phy0 {
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-
-	vbus-supply = <&vbus0_usb2>;
-	status = "okay";
-};
-
-&usb2_phy1 {
-	pinctrl-0 = <&usb1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&usb3_peri0 {
-	phys = <&usb3_phy0>;
-	phy-names = "usb";
-
-	companion = <&xhci0>;
-
-	status = "okay";
-};
-
-&usb3_phy0 {
-	status = "okay";
-};
-
-&usb3s0_clk {
-	clock-frequency = <100000000>;
-};
-
-&vin0 {
-	status = "okay";
-};
-
-&vin1 {
-	status = "okay";
-};
-
-&vin2 {
-	status = "okay";
-};
-
-&vin3 {
-	status = "okay";
-};
-
-&vin4 {
-	status = "okay";
-};
-
-&vin5 {
-	status = "okay";
-};
-
-&vin6 {
-	status = "okay";
-};
-
-&vin7 {
-	status = "okay";
-};
-
-&xhci0 {
-	pinctrl-0 = <&usb30_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-#ifdef SOC_HAS_USB2_CH2
-&ehci2 {
-	status = "okay";
-};
-
-&ohci2 {
-	status = "okay";
-};
-
-&pfc {
-	usb2_pins: usb2 {
-		groups = "usb2";
-		function = "usb2";
-	};
-};
-
-&usb2_phy2 {
-	pinctrl-0 = <&usb2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-#endif /* SOC_HAS_USB2_CH2 */
diff --git a/arch/arm/dts/salvator-x.dtsi b/arch/arm/dts/salvator-x.dtsi
deleted file mode 100644
index ddee50e6463..00000000000
--- a/arch/arm/dts/salvator-x.dtsi
+++ /dev/null
@@ -1,29 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree Source for the Salvator-X board
- *
- * Copyright (C) 2015-2016 Renesas Electronics Corp.
- */
-
-#include "salvator-common.dtsi"
-
-/ {
-	model = "Renesas Salvator-X board";
-	compatible = "renesas,salvator-x";
-};
-
-&extal_clk {
-	clock-frequency = <16666666>;
-};
-
-&i2c4 {
-	clock-frequency = <400000>;
-
-	versaclock5: clock-generator@6a {
-		compatible = "idt,5p49v5923";
-		reg = <0x6a>;
-		#clock-cells = <1>;
-		clocks = <&x23_clk>;
-		clock-names = "xin";
-	};
-};
diff --git a/arch/arm/dts/salvator-xs.dtsi b/arch/arm/dts/salvator-xs.dtsi
deleted file mode 100644
index 08b925624e1..00000000000
--- a/arch/arm/dts/salvator-xs.dtsi
+++ /dev/null
@@ -1,85 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree Source for the Salvator-X 2nd version board
- *
- * Copyright (C) 2015-2017 Renesas Electronics Corp.
- */
-
-#include "salvator-common.dtsi"
-
-/ {
-	model = "Renesas Salvator-X 2nd version board";
-	compatible = "renesas,salvator-xs";
-};
-
-&extal_clk {
-	clock-frequency = <16640000>;
-};
-
-&i2c4 {
-	clock-frequency = <400000>;
-
-	versaclock6: clock-generator@6a {
-		compatible = "idt,5p49v6901";
-		reg = <0x6a>;
-		#clock-cells = <1>;
-		clocks = <&x23_clk>;
-		clock-names = "xin";
-	};
-};
-
-#ifdef SOC_HAS_SATA
-&pca9654 {
-	pcie-sata-switch-hog {
-		gpio-hog;
-		gpios = <7 GPIO_ACTIVE_HIGH>;
-		output-low; /* enable SATA by default */
-		line-name = "PCIE/SATA switch";
-	};
-};
-
-/* SW12-7 must be set 'Off' (MD12 set to 1) which is not the default! */
-#endif /* SOC_HAS_SATA */
-
-#ifdef SOC_HAS_USB2_CH3
-&ehci3 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&hsusb3 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&ohci3 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&pfc {
-	/*
-	 * - On Salvator-X[S], GP6_3[01] are connected to ADV7482 as irq pins
-	 *   (when SW31 is the default setting on Salvator-XS).
-	 * - If SW31 is the default setting, you cannot use USB2.0 ch3 on
-	 *   r8a77951 with Salvator-XS.
-	 *   Hence the SW31 setting must be changed like 2) below.
-	 *   1) Default setting of SW31: ON-ON-OFF-OFF-OFF-OFF:
-	 *	- Connect GP6_3[01] to ADV7842.
-	 *   2) Changed setting of SW31: OFF-OFF-ON-ON-ON-ON:
-	 *	- Connect GP6_3[01] to BD082065 (USB2.0 ch3's host power).
-	 *	- Connect GP6_{04,21} to ADV7842.
-	 */
-	usb2_ch3_pins: usb2_ch3 {
-		groups = "usb2_ch3";
-		function = "usb2_ch3";
-	};
-};
-
-&usb2_phy3 {
-	pinctrl-0 = <&usb2_ch3_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-#endif /* SOC_HAS_USB2_CH3 */
diff --git a/arch/arm/dts/ulcb-audio-graph-card.dtsi b/arch/arm/dts/ulcb-audio-graph-card.dtsi
deleted file mode 100644
index 3be54df645e..00000000000
--- a/arch/arm/dts/ulcb-audio-graph-card.dtsi
+++ /dev/null
@@ -1,85 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree for ULCB + Audio Graph Card
- *
- * Copyright (C) 2022 Renesas Electronics Corp.
- */
-
-/*
- *	(A) CPU0 <-----> ak4613
- *	(B) CPU1  -----> HDMI
- *
- *	(A) aplay   -D plughw:0,0 xxx.wav
- *	(B) aplay   -D plughw:0,1 xxx.wav
- *
- *	(A) arecord -D plughw:0,0 xxx.wav
- */
-
-/ {
-	sound_card: sound {
-		compatible = "audio-graph-card";
-		label = "rcar-sound";
-
-		dais = <&rsnd_port0 /* (A) CPU0 <-> ak4613 */
-			&rsnd_port1 /* (B) CPU1  -> HDMI   */
-		>;
-	};
-};
-
-&ak4613 {
-	#sound-dai-cells = <0>;
-
-	port {
-		/*
-		 * (A) CPU0 <-> ak4613
-		 */
-		ak4613_endpoint: endpoint {
-			remote-endpoint = <&rsnd_for_ak4613>;
-		};
-	};
-};
-
-&hdmi0 {
-	ports {
-		port@2 {
-			/*
-			 * (B) CPU1 -> HDMI
-			 */
-			dw_hdmi0_snd_in: endpoint {
-				remote-endpoint = <&rsnd_for_hdmi>;
-			};
-		};
-	};
-};
-
-&rcar_sound {
-	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		rsnd_port0: port@0 {
-			/*
-			 * (A) CPU0 <-> ak4613
-			 */
-			reg = <0>;
-			rsnd_for_ak4613: endpoint {
-				remote-endpoint = <&ak4613_endpoint>;
-				bitclock-master;
-				frame-master;
-				playback = <&ssi0>, <&src0>, <&dvc0>;
-				capture  = <&ssi1>, <&src1>, <&dvc1>;
-			};
-		};
-		rsnd_port1: port@1 {
-			/*
-			 * (B) CPU1 -> HDMI
-			 */
-			reg = <1>;
-			rsnd_for_hdmi: endpoint {
-				remote-endpoint = <&dw_hdmi0_snd_in>;
-				bitclock-master;
-				frame-master;
-				playback = <&ssi2>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/dts/ulcb-audio-graph-card2.dtsi b/arch/arm/dts/ulcb-audio-graph-card2.dtsi
deleted file mode 100644
index 5ebec123584..00000000000
--- a/arch/arm/dts/ulcb-audio-graph-card2.dtsi
+++ /dev/null
@@ -1,26 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree for ULCB + Audio Graph Card2
- *
- * Copyright (C) 2022 Renesas Electronics Corp.
- */
-
-/*
- *	(A) CPU0 <----> ak4613
- *	(B) CPU1  ----> HDMI
- *
- *	(A) aplay   -D plughw:0,0 xxx.wav
- *	(B) aplay   -D plughw:0,1 xxx.wav
- *
- *	(A) arecord -D plughw:0,0 xxx.wav
- */
-#include "ulcb-audio-graph-card.dtsi"
-
-&sound_card {
-	compatible = "audio-graph-card2";
-
-	/delete-property/ dais;
-	links = <&rsnd_port0	/* (A) CPU0 <-> ak4613 */
-		 &rsnd_port1	/* (B) CPU1  -> HDMI   */
-		>;
-};
diff --git a/arch/arm/dts/ulcb.dtsi b/arch/arm/dts/ulcb.dtsi
deleted file mode 100644
index 0be2716659e..00000000000
--- a/arch/arm/dts/ulcb.dtsi
+++ /dev/null
@@ -1,509 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Device Tree Source for the R-Car Gen3 ULCB board
- *
- * Copyright (C) 2016 Renesas Electronics Corp.
- * Copyright (C) 2016 Cogent Embedded, Inc.
- */
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
-	model = "Renesas R-Car Gen3 ULCB board";
-
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-		i2c5 = &i2c5;
-		i2c6 = &i2c6;
-		i2c7 = &i2c_dvfs;
-		serial0 = &scif2;
-		ethernet0 = &avb;
-		mmc0 = &sdhi2;
-		mmc1 = &sdhi0;
-	};
-
-	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
-		stdout-path = "serial0:115200n8";
-	};
-
-	audio_clkout: audio-clkout {
-		/*
-		 * This is same as <&rcar_sound 0>
-		 * but needed to avoid cs2000/rcar_sound probe dead-lock
-		 */
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <12288000>;
-	};
-
-	hdmi0-out {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi0_con: endpoint {
-				remote-endpoint = <&rcar_dw_hdmi0_out>;
-			};
-		};
-	};
-
-	keyboard {
-		compatible = "gpio-keys";
-
-		key-1 {
-			linux,code = <KEY_1>;
-			label = "SW3";
-			wakeup-source;
-			debounce-interval = <20>;
-			gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led5 {
-			gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
-		};
-		led6 {
-			gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	reg_1p8v: regulator-1p8v {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	vcc_sdhi0: regulator-vcc-sdhi0 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI0 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi0: regulator-vccq-sdhi0 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI0 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1>, <1800000 0>;
-	};
-
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
-	};
-
-	x23_clk: x23-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <25000000>;
-	};
-};
-
-&a57_0 {
-	cpu-supply = <&dvfs>;
-};
-
-&audio_clk_a {
-	clock-frequency = <22579200>;
-};
-
-&avb {
-	pinctrl-0 = <&avb_pins>;
-	pinctrl-names = "default";
-	phy-handle = <&phy0>;
-	tx-internal-delay-ps = <2000>;
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		compatible = "ethernet-phy-id0022.1622",
-			     "ethernet-phy-ieee802.3-c22";
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
-	};
-};
-
-&du {
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
-};
-
-&extal_clk {
-	clock-frequency = <16666666>;
-};
-
-&extalr_clk {
-	clock-frequency = <32768>;
-};
-
-&hdmi0 {
-	status = "okay";
-
-	ports {
-		port@1 {
-			reg = <1>;
-			rcar_dw_hdmi0_out: endpoint {
-				remote-endpoint = <&hdmi0_con>;
-			};
-		};
-		port@2 {
-			reg = <2>;
-		};
-	};
-};
-
-&i2c2 {
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-
-	clock-frequency = <100000>;
-
-	ak4613: codec@10 {
-		compatible = "asahi-kasei,ak4613";
-		reg = <0x10>;
-		clocks = <&rcar_sound 3>;
-
-		asahi-kasei,in1-single-end;
-		asahi-kasei,in2-single-end;
-		asahi-kasei,out1-single-end;
-		asahi-kasei,out2-single-end;
-		asahi-kasei,out3-single-end;
-		asahi-kasei,out4-single-end;
-		asahi-kasei,out5-single-end;
-		asahi-kasei,out6-single-end;
-	};
-
-	cs2000: clk-multiplier@4f {
-		#clock-cells = <0>;
-		compatible = "cirrus,cs2000-cp";
-		reg = <0x4f>;
-		clocks = <&audio_clkout>, <&x12_clk>;
-		clock-names = "clk_in", "ref_clk";
-
-		assigned-clocks = <&cs2000>;
-		assigned-clock-rates = <24576000>; /* 1/1 divide */
-	};
-};
-
-&i2c4 {
-	status = "okay";
-
-	clock-frequency = <400000>;
-
-	versaclock5: clock-generator@6a {
-		compatible = "idt,5p49v5925";
-		reg = <0x6a>;
-		#clock-cells = <1>;
-		clocks = <&x23_clk>;
-		clock-names = "xin";
-	};
-};
-
-&i2c_dvfs {
-	status = "okay";
-
-	clock-frequency = <400000>;
-
-	pmic: pmic@30 {
-		pinctrl-0 = <&irq0_pins>;
-		pinctrl-names = "default";
-
-		compatible = "rohm,bd9571mwv";
-		reg = <0x30>;
-		interrupt-parent = <&intc_ex>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		gpio-controller;
-		#gpio-cells = <2>;
-		rohm,ddr-backup-power = <0xf>;
-		rohm,rstbmode-pulse;
-
-		regulators {
-			dvfs: dvfs {
-				regulator-name = "dvfs";
-				regulator-min-microvolt = <750000>;
-				regulator-max-microvolt = <1030000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-		};
-	};
-
-	eeprom@50 {
-		compatible = "rohm,br24t01", "atmel,24c01";
-		reg = <0x50>;
-		pagesize = <8>;
-	};
-};
-
-&ohci1 {
-	status = "okay";
-};
-
-&pfc {
-	pinctrl-0 = <&scif_clk_pins>;
-	pinctrl-names = "default";
-
-	avb_pins: avb {
-		mux {
-			groups = "avb_link", "avb_mdio", "avb_mii";
-			function = "avb";
-		};
-
-		pins_mdio {
-			groups = "avb_mdio";
-			drive-strength = <24>;
-		};
-
-		pins_mii_tx {
-			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
-			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
-			drive-strength = <12>;
-		};
-	};
-
-	i2c2_pins: i2c2 {
-		groups = "i2c2_a";
-		function = "i2c2";
-	};
-
-	irq0_pins: irq0 {
-		groups = "intc_ex_irq0";
-		function = "intc_ex";
-	};
-
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
-	};
-
-	scif_clk_pins: scif_clk {
-		groups = "scif_clk_a";
-		function = "scif_clk";
-	};
-
-	sdhi0_pins: sd0 {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <3300>;
-	};
-
-	sdhi0_pins_uhs: sd0_uhs {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <1800>;
-	};
-
-	sdhi2_pins: sd2 {
-		groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
-		function = "sdhi2";
-		power-source = <1800>;
-	};
-
-	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
-		function = "ssi";
-	};
-
-	sound_clk_pins: sound-clk {
-		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
-			 "audio_clkout_a", "audio_clkout3_a";
-		function = "audio_clk";
-	};
-
-	usb1_pins: usb1 {
-		groups = "usb1";
-		function = "usb1";
-	};
-};
-
-&rcar_sound {
-	pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
-	pinctrl-names = "default";
-
-	/* audio_clkout0/1/2/3 */
-	#clock-cells = <1>;
-	clock-frequency = <12288000 11289600>;
-
-	status = "okay";
-
-	/* update <audio_clk_b> to <cs2000> */
-	clocks = <&cpg CPG_MOD 1005>,
-		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
-		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
-		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
-		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
-		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
-		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
-		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
-		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
-		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
-		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
-		 <&audio_clk_a>, <&cs2000>,
-		 <&audio_clk_c>,
-		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
-};
-
-&rpc {
-	/* Left disabled.  To be enabled by firmware when unlocked. */
-
-	flash@0 {
-		compatible = "cypress,hyperflash", "cfi-flash";
-		reg = <0>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			bootparam@0 {
-				reg = <0x00000000 0x040000>;
-				read-only;
-			};
-			bl2@40000 {
-				reg = <0x00040000 0x140000>;
-				read-only;
-			};
-			cert_header_sa6@180000 {
-				reg = <0x00180000 0x040000>;
-				read-only;
-			};
-			bl31@1c0000 {
-				reg = <0x001c0000 0x040000>;
-				read-only;
-			};
-			tee@200000 {
-				reg = <0x00200000 0x440000>;
-				read-only;
-			};
-			uboot@640000 {
-				reg = <0x00640000 0x100000>;
-				read-only;
-			};
-			dtb@740000 {
-				reg = <0x00740000 0x080000>;
-			};
-			kernel@7c0000 {
-				reg = <0x007c0000 0x1400000>;
-			};
-			user@1bc0000 {
-				reg = <0x01bc0000 0x2440000>;
-			};
-		};
-	};
-};
-
-&rwdt {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&scif_clk {
-	clock-frequency = <14745600>;
-};
-
-&sdhi0 {
-	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-1 = <&sdhi0_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi0>;
-	vqmmc-supply = <&vccq_sdhi0>;
-	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-	status = "okay";
-};
-
-&sdhi2 {
-	/* used for on-board 8bit eMMC */
-	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-1 = <&sdhi2_pins>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	bus-width = <8>;
-	mmc-hs200-1_8v;
-	mmc-hs400-1_8v;
-	no-sd;
-	no-sdio;
-	non-removable;
-	full-pwr-cycle-in-suspend;
-	status = "okay";
-};
-
-&ssi1 {
-	shared-pin;
-};
-
-&usb2_phy1 {
-	pinctrl-0 = <&usb1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-
-/*
- * For sound-test.
- *
- * We can switch Audio Card for testing
- *
- * #include "ulcb-simple-audio-card.dtsi"
- * #include "ulcb-simple-audio-card-mix+split.dtsi"
- * #include "ulcb-audio-graph-card.dtsi"
- * #include "ulcb-audio-graph-card-mix+split.dtsi"
- * #include "ulcb-audio-graph-card2-mix+split.dtsi"
- */
-#include "ulcb-audio-graph-card2.dtsi"