doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

1 files changed, 166 insertions, 0 deletions

diff --git a/board/freescale/mpc8572ds/README b/board/freescale/mpc8572ds/README
new file mode 100644
index 00000000000..57fd2ad6160
--- /dev/null
+++ b/board/freescale/mpc8572ds/README
@@ -0,0 +1,166 @@
+Overview
+--------
+MPC8572DS is a high-performance computing, evaluation and development platform
+supporting the mpc8572 PowerTM processor.
+
+Building U-boot
+-----------
+	make MPC8572DS_config
+	make
+
+Flash Banks
+-----------
+MPC8572DS board has two flash banks. They are both present on boot, but their
+locations can be swapped using the dip-switch SW9[1:2].
+
+Booting is always from the boot bank at 0xec00_0000.
+
+
+Memory Map
+----------
+
+0xe800_0000 - 0xebff_ffff	Alternate bank		64MB
+0xec00_0000 - 0xefff_ffff	Boot bank		64MB
+
+0xebf8_0000 - 0xebff_ffff	Alternate u-boot address	512KB
+0xeff8_0000 - 0xefff_ffff	Boot u-boot address		512KB
+
+
+Flashing Images
+---------------
+
+To place a new u-boot image in the alternate flash bank and then reset with that
+ new image temporarily, use this:
+
+	tftp 1000000 u-boot.bin
+	erase ebf80000 ebffffff
+	cp.b 1000000 ebf80000 80000
+	pixis_reset altbank
+
+
+To program the image in the boot flash bank:
+
+	tftp 1000000 u-boot.bin
+	protect off all
+	erase eff80000 ffffffff
+	cp.b 1000000 eff80000 80000
+
+
+The pixis_reset command
+-----------------------
+The command - "pixis_reset", is introduced to reset mpc8572ds board
+using the FPGA sequencer.  When the board restarts, it has the option
+of using either the current or alternate flash bank as the boot
+image, with or without the watchdog timer enabled, and finally with
+or without frequency changes.
+
+Usage is;
+
+	pixis_reset
+	pixis_reset altbank
+	pixis_reset altbank wd
+	pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
+	pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
+
+Examples:
+
+	/* reset to current bank, like "reset" command */
+	pixis_reset
+
+	/* reset board but use the to alternate flash bank */
+	pixis_reset altbank
+
+
+Using the Device Tree Source File
+---------------------------------
+To create the DTB (Device Tree Binary) image file,
+use a command similar to this:
+
+	dtc -b 0 -f -I dts -O dtb mpc8572ds.dts > mpc8572ds.dtb
+
+Likely, that .dts file will come from here;
+
+	linux-2.6/arch/powerpc/boot/dts/mpc8572ds.dts
+
+
+Booting Linux
+-------------
+
+Place a linux uImage in the TFTP disk area.
+
+	tftp 1000000 uImage.8572
+	tftp c00000 mpc8572ds.dtb
+	bootm 1000000 - c00000
+
+
+Implementing AMP(Asymmetric MultiProcessing)
+-------------
+1. Build kernel image for core0:
+
+	a. $ make 85xx/mpc8572_ds_defconfig
+
+	b. $ make menuconfig
+	   - un-select "Processor support"->"Symetric multi-processing support"
+
+	c. $ make uImage
+
+	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core0
+
+2. Build kernel image for core1:
+
+	a. $ make 85xx/mpc8572_ds_defconfig
+
+	b. $ make menuconfig
+	   - Un-select "Processor support"->"Symetric multi-processing support"
+	   - Select "Advanced setup" -> " Prompt for advanced kernel
+	     configuration options"
+		- Select "Set physical address where the kernel is loaded" and
+		  set it to 0x20000000, assuming core1 will start from 512MB.
+		- Select "Set custom page offset address"
+		- Select "Set custom kernel base address"
+		- Select "Set maximum low memory"
+	   - "Exit" and save the selection.
+
+	c. $ make uImage
+
+	d. $ cp arch/powerpc/boot/uImage /tftpboot/uImage.core1
+
+3. Create dtb for core0:
+
+	$ dtc -I dts -O dtb -f -b 0 arch/powerpc/boot/dts/mpc8572ds_core0.dts > /tftpboot/mpc8572ds_core0.dtb
+
+4. Create dtb for core1:
+
+	$ dtc -I dts -O dtb -f -b 1 arch/powerpc/boot/dts/mpc8572ds_core1.dts > /tftpboot/mpc8572ds_core1.dtb
+
+5. Bring up two cores separately:
+
+	a. Power on the board, under u-boot prompt:
+		=> setenv <serverip>
+		=> setenv <ipaddr>
+		=> setenv bootargs root=/dev/ram rw console=ttyS0,115200
+	b. Bring up core1's kernel first:
+		=> setenv bootm_low 0x20000000
+		=> setenv bootm_size 0x10000000
+		=> tftp 21000000 8572/uImage.core1
+		=> tftp 22000000 8572/ramdiskfile
+		=> tftp 20c00000 8572/mpc8572ds_core1.dtb
+		=> interrupts off
+		=> bootm start 21000000 22000000 20c00000
+		=> bootm loados
+		=> bootm ramdisk
+		=> bootm fdt
+		=> fdt boardsetup
+		=> fdt chosen $initrd_start $initrd_end
+		=> bootm prep
+		=> cpu 1 release $bootm_low - $fdtaddr -
+	c. Bring up core0's kernel(on the same u-boot console):
+		=> setenv bootm_low 0
+		=> setenv bootm_size 0x20000000
+		=> tftp 1000000 8572/uImage.core0
+		=> tftp 2000000 8572/ramdiskfile
+		=> tftp c00000 8572/mpc8572ds_core0.dtb
+		=> bootm 1000000 2000000 c00000
+
+Please note only core0 will run u-boot, core1 starts kernel directly after
+"cpu release" command is issued.