powerpc: T1023RDB: Remove macro CONFIG_T1023RDB

Use TARGET_T1023RDB from Kconfig instead.

Signed-off-by: York Sun <york.sun@nxp.com>

4 files changed, 10 insertions, 10 deletions

diff --git a/board/freescale/t102xrdb/ddr.c b/board/freescale/t102xrdb/ddr.c
index 9e1b16bfcdf..c09199fb036 100644
--- a/board/freescale/t102xrdb/ddr.c
+++ b/board/freescale/t102xrdb/ddr.c
@@ -136,7 +136,7 @@ found:
 	popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
 #endif
 
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 	popts->wrlvl_ctl_2 = 0x07070606;
 	popts->half_strength_driver_enable = 1;
 	popts->cpo_sample = 0x43;
diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c
index 02b283d26ff..dadfaf17391 100644
--- a/board/freescale/t102xrdb/eth_t102xrdb.c
+++ b/board/freescale/t102xrdb/eth_t102xrdb.c
@@ -73,7 +73,7 @@ int board_eth_init(bd_t *bis)
 	case 0x135:
 		/* set the on-board 2.5G SGMII AQR105 PHY */
 		fm_info_set_phy_address(FM1_DTSEC3, SGMII_AQR_PHY_ADDR);
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 		/* set the on-board 1G SGMII RTL8211F PHY */
 		fm_info_set_phy_address(FM1_DTSEC1, SGMII_RTK_PHY_ADDR);
 #endif
@@ -92,7 +92,7 @@ int board_eth_init(bd_t *bis)
 			fm_info_set_mdio(i, dev);
 			break;
 		case PHY_INTERFACE_MODE_SGMII:
-#if defined(CONFIG_T1023RDB)
+#if defined(CONFIG_TARGET_T1023RDB)
 			dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
 #elif defined(CONFIG_T1024RDB)
 			dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
diff --git a/board/freescale/t102xrdb/t102xrdb.c b/board/freescale/t102xrdb/t102xrdb.c
index 24df4b440f0..317472619f3 100644
--- a/board/freescale/t102xrdb/t102xrdb.c
+++ b/board/freescale/t102xrdb/t102xrdb.c
@@ -19,7 +19,7 @@
 #include "t102xrdb.h"
 #ifdef CONFIG_T1024RDB
 #include "cpld.h"
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #include <i2c.h>
 #include <mmc.h>
 #endif
@@ -27,7 +27,7 @@
 
 DECLARE_GLOBAL_DATA_PTR;
 
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 enum {
 	GPIO1_SD_SEL    = 0x00020000, /* GPIO1_14, 0: eMMC, 1:SD/MMC */
 	GPIO1_EMMC_SEL,
@@ -54,7 +54,7 @@ int checkboard(void)
 #if defined(CONFIG_T1024RDB)
 	printf("Board rev: 0x%02x CPLD ver: 0x%02x, ",
 	       CPLD_READ(hw_ver), CPLD_READ(sw_ver));
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 	printf("Rev%c, ", t1023rdb_ctrl(GPIO3_GET_VERSION) + 'B');
 #endif
 	printf("boot from ");
@@ -74,7 +74,7 @@ int checkboard(void)
 		reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
 		printf("NOR vBank%d\n", reg);
 	}
-#elif defined(CONFIG_T1023RDB)
+#elif defined(CONFIG_TARGET_T1023RDB)
 #ifdef CONFIG_NAND
 	puts("NAND\n");
 #else
@@ -196,7 +196,7 @@ int ft_board_setup(void *blob, bd_t *bd)
 	fdt_fixup_board_enet(blob);
 #endif
 
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 	if (t1023rdb_ctrl(GPIO3_GET_VERSION) > 0)
 		fdt_enable_nor(blob);
 #endif
@@ -204,7 +204,7 @@ int ft_board_setup(void *blob, bd_t *bd)
 	return 0;
 }
 
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 /* Enable NOR flash for RevC */
 static void fdt_enable_nor(void *blob)
 {
diff --git a/board/freescale/t102xrdb/t102xrdb.h b/board/freescale/t102xrdb/t102xrdb.h
index ae5c60f86e6..6634e7a9f43 100644
--- a/board/freescale/t102xrdb/t102xrdb.h
+++ b/board/freescale/t102xrdb/t102xrdb.h
@@ -9,7 +9,7 @@
 
 void fdt_fixup_board_enet(void *blob);
 void pci_of_setup(void *blob, bd_t *bd);
-#ifdef CONFIG_T1023RDB
+#ifdef CONFIG_TARGET_T1023RDB
 static u32 t1023rdb_ctrl(u32 ctrl_type);
 static void fdt_enable_nor(void *blob);
 #endif