Merge branch 'master' of git://git.denx.de/u-boot-i2c

The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
	board/sandburst/common/ppc440gx_i2c.c
	board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>

3 files changed, 6 insertions, 36 deletions

diff --git a/board/keymile/common/ivm.c b/board/keymile/common/ivm.c
index 47c4450e3d5..aabd3a85b72 100644
--- a/board/keymile/common/ivm.c
+++ b/board/keymile/common/ivm.c
@@ -298,29 +298,14 @@ int ivm_analyze_eeprom(unsigned char *buf, int len)
 
 int ivm_read_eeprom(void)
 {
-#if defined(CONFIG_I2C_MUX)
-	I2C_MUX_DEVICE *dev = NULL;
-#endif
 	uchar i2c_buffer[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
-	uchar	*buf;
-	unsigned long dev_addr = CONFIG_SYS_IVM_EEPROM_ADR;
 	int ret;
 
-#if defined(CONFIG_I2C_MUX)
-	/* First init the Bus, select the Bus */
-	buf = (unsigned char *) getenv("EEprom_ivm");
-	if (buf != NULL)
-		dev = i2c_mux_ident_muxstring(buf);
-	if (dev == NULL) {
-		printf("Error couldnt add Bus for IVM\n");
-		return -1;
-	}
-	i2c_set_bus_num(dev->busid);
-#endif
+	i2c_set_bus_num(CONFIG_KM_IVM_BUS);
 	/* add deblocking here */
 	i2c_make_abort();
 
-	ret = i2c_read(dev_addr, 0, 1, i2c_buffer,
+	ret = i2c_read(CONFIG_SYS_IVM_EEPROM_ADR, 0, 1, i2c_buffer,
 		CONFIG_SYS_IVM_EEPROM_MAX_LEN);
 	if (ret != 0) {
 		printf("Error reading EEprom\n");
diff --git a/board/keymile/km83xx/km83xx.c b/board/keymile/km83xx/km83xx.c
index b5ea7ae95b4..cd861c9f125 100644
--- a/board/keymile/km83xx/km83xx.c
+++ b/board/keymile/km83xx/km83xx.c
@@ -92,19 +92,6 @@ const qe_iop_conf_t qe_iop_conf_tab[] = {
 	{0,  0, 0, 0, QE_IOP_TAB_END},
 };
 
-static int board_init_i2c_busses(void)
-{
-	I2C_MUX_DEVICE *dev = NULL;
-	uchar *dtt_bus = (uchar *)"pca9547:70:a";
-
-	/* Set up the Bus for the DTTs */
-	dev = i2c_mux_ident_muxstring(dtt_bus);
-	if (dev == NULL)
-		printf("Error couldn't add Bus for DTT\n");
-
-	return 0;
-}
-
 #if defined(CONFIG_SUVD3)
 const uint upma_table[] = {
 	0x1ffedc00, 0x0ffcdc80, 0x0ffcdc80, 0x0ffcdc04, /* Words 0 to 3 */
@@ -203,8 +190,6 @@ int board_early_init_r(void)
 
 int misc_init_r(void)
 {
-	/* add board specific i2c busses */
-	board_init_i2c_busses();
 	return 0;
 }
 
diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c
index e76acc0daca..481876b2ed8 100644
--- a/board/keymile/km_arm/km_arm.c
+++ b/board/keymile/km_arm/km_arm.c
@@ -47,7 +47,7 @@ static const u32 kwmpp_config[] = {
 	MPP5_NF_IO7,
 	MPP6_SYSRST_OUTn,
 	MPP7_PEX_RST_OUTn,
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	MPP8_GPIO,		/* SDA */
 	MPP9_GPIO,		/* SCL */
 #endif
@@ -218,7 +218,7 @@ int misc_init_r(void)
 
 int board_early_init_f(void)
 {
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	u32 tmp;
 
 	/* set the 2 bitbang i2c pins as output gpios */
@@ -244,7 +244,7 @@ int board_init(void)
 	kw_gpio_set_valid(KM_FLASH_GPIO_PIN, 1);
 	kw_gpio_direction_output(KM_FLASH_GPIO_PIN, 1);
 
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 	/*
 	 * Reinit the GPIO for I2C Bitbang driver so that the now
 	 * available gpio framework is consistent. The calls to
@@ -424,7 +424,7 @@ int hush_init_var(void)
 }
 #endif
 
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
 void set_sda(int state)
 {
 	I2C_ACTIVE;