Patch by Denis Peter, 19 Mai 2003:

add support for the MIP405-3 board

1 files changed, 159 insertions, 0 deletions

diff --git a/board/mpl/pip405/pip405.h b/board/mpl/pip405/pip405.h
index 58b18e96010..10f647994cd 100644
--- a/board/mpl/pip405/pip405.h
+++ b/board/mpl/pip405/pip405.h
@@ -51,3 +51,162 @@ void user_led1(unsigned char on);
 #define PIIX4_IDE_DEV_ID		0x7111
 
 
+/* timings */
+/* PLD (CS7) */
+#define PLD_BME	0 	/* Burst disable */
+#define PLD_TWE	5	/* 5 * 30ns 120ns Waitstates (access=TWT+1+TH) */
+#define PLD_CSN	1	/* Chipselect is driven inactive for 1 Cycle BTW transfers */
+#define PLD_OEN	1	/* Cycles from CS low to OE low   */
+#define PLD_WBN	1	/* Cycles from CS low to WE low   */
+#define PLD_WBF	1	/* Cycles from WE high to CS high */
+#define PLD_TH	2	/* Number of hold cycles after transfer */
+#define PLD_RE	0	/* Ready disabled */
+#define PLD_SOR	1	/* Sample on Ready disabled */
+#define PLD_BEM	0	/* Byte Write only active on Write cycles */
+#define PLD_PEN	0	/* Parity disable */
+#define PLD_AP 	((PLD_BME << 31) + (PLD_TWE << 23) + (PLD_CSN << 18) + (PLD_OEN << 16) + (PLD_WBN << 14) + \
+					(PLD_WBF << 12) + (PLD_TH << 9) + (PLD_RE << 8) + (PLD_SOR << 7) + (PLD_BEM << 6) + (PLD_PEN << 5))
+
+/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
+#define PLD_BS	0	/* 1 MByte */
+/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */
+#define PLD_BU	3	/* R/W */
+/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */
+#define PLD_BW	0	/* 16Bit */
+#define PLD_CR	((PER_PLD_ADDR & 0xfff00000) + (PLD_BS << 17) + (PLD_BU << 15) + (PLD_BW << 13))
+
+
+/* timings */
+
+#define PER_BOARD_ADDR (PER_UART1_ADDR+(1024*1024))
+/* Dummy CS to get the board revision */
+#define BOARD_BME	0 	/* Burst disable */
+#define BOARD_TWE	255	/* 255 * 30ns 120ns Waitstates (access=TWT+1+TH) */
+#define BOARD_CSN	1	/* Chipselect is driven inactive for 1 Cycle BTW transfers */
+#define BOARD_OEN	1	/* Cycles from CS low to OE low   */
+#define BOARD_WBN	1	/* Cycles from CS low to WE low   */
+#define BOARD_WBF	1	/* Cycles from WE high to CS high */
+#define BOARD_TH	2	/* Number of hold cycles after transfer */
+#define BOARD_RE	0	/* Ready disabled */
+#define BOARD_SOR	1	/* Sample on Ready disabled */
+#define BOARD_BEM	0	/* Byte Write only active on Write cycles */
+#define BOARD_PEN	0	/* Parity disable */
+#define BOARD_AP 	((BOARD_BME << 31) + (BOARD_TWE << 23) + (BOARD_CSN << 18) + (BOARD_OEN << 16) + (BOARD_WBN << 14) + \
+					(BOARD_WBF << 12) + (BOARD_TH << 9) + (BOARD_RE << 8) + (BOARD_SOR << 7) + (BOARD_BEM << 6) + (BOARD_PEN << 5))
+
+/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
+#define BOARD_BS	0	/* 1 MByte */
+/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */
+#define BOARD_BU	3	/* R/W */
+/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */
+#define BOARD_BW	0	/* 16Bit */
+#define BOARD_CR	((PER_BOARD_ADDR & 0xfff00000) + (BOARD_BS << 17) + (BOARD_BU << 15) + (BOARD_BW << 13))
+
+
+/* UART0 CS2 */
+#define UART0_BME	0 	/* Burst disable */
+#define UART0_TWE	7	/* 7 * 30ns 210ns Waitstates (access=TWT+1+TH) */
+#define UART0_CSN	1	/* Chipselect is driven inactive for 1 Cycle BTW transfers */
+#define UART0_OEN	1	/* Cycles from CS low to OE low   */
+#define UART0_WBN	1	/* Cycles from CS low to WE low   */
+#define UART0_WBF	1	/* Cycles from WE high to CS high */
+#define UART0_TH	2	/* Number of hold cycles after transfer */
+#define UART0_RE	0	/* Ready disabled */
+#define UART0_SOR	1	/* Sample on Ready disabled */
+#define UART0_BEM	0	/* Byte Write only active on Write cycles */
+#define UART0_PEN	0	/* Parity disable */
+#define UART0_AP 	((UART0_BME << 31) + (UART0_TWE << 23) + (UART0_CSN << 18) + (UART0_OEN << 16) + (UART0_WBN << 14) + \
+					(UART0_WBF << 12) + (UART0_TH << 9) + (UART0_RE << 8) + (UART0_SOR << 7) + (UART0_BEM << 6) + (UART0_PEN << 5))
+
+/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
+#define UART0_BS	0	/* 1 MByte */
+/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */
+#define UART0_BU	3	/* R/W */
+/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */
+#define UART0_BW	0	/* 8Bit */
+#define UART0_CR	((PER_UART0_ADDR & 0xfff00000) + (UART0_BS << 17) + (UART0_BU << 15) + (UART0_BW << 13))
+
+/* UART1 CS3 */
+#define UART1_AP UART0_AP /* same timing as UART0 */
+#define UART1_CR	((PER_UART1_ADDR & 0xfff00000) + (UART0_BS << 17) + (UART0_BU << 15) + (UART0_BW << 13))
+
+
+
+/* Flash CS0 or CS 1 */
+/* 0x7F8FFE80 slowest timing at all... */
+#define FLASH_BME_B	1 	/* Burst enable */
+#define FLASH_FWT_B	0x6	/* 6 * 30ns 210ns First Wait Access */
+#define FLASH_BWT_B	0x6	/* 6 * 30ns 210ns Burst Wait Access */
+#define FLASH_BME	0 	/* Burst disable */
+#define FLASH_TWE	0xb/* 11 * 30ns 330ns Waitstates (access=TWT+1+TH) */
+#define FLASH_CSN	0	/* Chipselect is driven inactive for 1 Cycle BTW transfers */
+#define FLASH_OEN	1	/* Cycles from CS low to OE low   */
+#define FLASH_WBN	1	/* Cycles from CS low to WE low   */
+#define FLASH_WBF	1	/* Cycles from WE high to CS high */
+#define FLASH_TH	2	/* Number of hold cycles after transfer */
+#define FLASH_RE	0	/* Ready disabled */
+#define FLASH_SOR	1	/* Sample on Ready disabled */
+#define FLASH_BEM	0	/* Byte Write only active on Write cycles */
+#define FLASH_PEN	0	/* Parity disable */
+/* Access Parameter Register for non Boot */
+#define FLASH_AP 	((FLASH_BME << 31) + (FLASH_TWE << 23) + (FLASH_CSN << 18) + (FLASH_OEN << 16) + (FLASH_WBN << 14) + \
+					(FLASH_WBF << 12) + (FLASH_TH << 9) + (FLASH_RE << 8) + (FLASH_SOR << 7) + (FLASH_BEM << 6) + (FLASH_PEN << 5))
+/* Access Parameter Register for Boot */
+#define FLASH_AP_B 	((FLASH_BME_B << 31) + (FLASH_FWT_B << 26) + (FLASH_BWT_B << 23) + (FLASH_CSN << 18) + (FLASH_OEN << 16) + (FLASH_WBN << 14) + \
+					(FLASH_WBF << 12) + (FLASH_TH << 9) + (FLASH_RE << 8) + (FLASH_SOR << 7) + (FLASH_BEM << 6) + (FLASH_PEN << 5))
+
+/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
+#define FLASH_BS	2	/* 4 MByte */
+/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */
+#define FLASH_BU	3	/* R/W */
+/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */
+#define FLASH_BW	1	/* 16Bit */
+/* CR register for Boot */
+#define FLASH_CR_B	((FLASH_BASE0_PRELIM & 0xfff00000) + (FLASH_BS << 17) + (FLASH_BU << 15) + (FLASH_BW << 13))
+/* CR register for non Boot */
+#define FLASH_CR	((MULTI_PURPOSE_SOCKET_ADDR & 0xfff00000) + (FLASH_BS << 17) + (FLASH_BU << 15) + (FLASH_BW << 13))
+
+/* MPS CS1 or CS0 */
+/* Boot CS: */
+#define MPS_BME_B	1 	/* Burst enable */
+#define MPS_FWT_B	0x6/* 6 * 30ns 210ns First Wait Access */
+#define MPS_BWT_B	0x6	/* 6 * 30ns 210ns Burst Wait Access */
+#define MPS_BME		0 	/* Burst disable */
+#define MPS_TWE		0xb/* 11 * 30ns 330ns Waitstates (access=TWT+1+TH) */
+#define MPS_CSN		0	/* Chipselect is driven inactive for 1 Cycle BTW transfers */
+#define MPS_OEN		1	/* Cycles from CS low to OE low   */
+#define MPS_WBN		1	/* Cycles from CS low to WE low   */
+#define MPS_WBF		1	/* Cycles from WE high to CS high */
+#define MPS_TH		2	/* Number of hold cycles after transfer */
+#define MPS_RE		0	/* Ready disabled */
+#define MPS_SOR		1	/* Sample on Ready disabled */
+#define MPS_BEM		0	/* Byte Write only active on Write cycles */
+#define MPS_PEN		0	/* Parity disable */
+/* Access Parameter Register for non Boot */
+#define MPS_AP 		((MPS_BME << 31) + (MPS_TWE << 23) + (MPS_CSN << 18) + (MPS_OEN << 16) + (MPS_WBN << 14) + \
+					(MPS_WBF << 12) + (MPS_TH << 9) + (MPS_RE << 8) + (MPS_SOR << 7) + (MPS_BEM << 6) + (MPS_PEN << 5))
+/* Access Parameter Register for Boot */
+#define MPS_AP_B 		((MPS_BME_B << 31) + (MPS_FWT_B << 26) + (MPS_BWT_B << 23) + (MPS_CSN << 18) + (MPS_OEN << 16) + (MPS_WBN << 14) + \
+					(MPS_WBF << 12) + (MPS_TH << 9) + (MPS_RE << 8) + (MPS_SOR << 7) + (MPS_BEM << 6) + (MPS_PEN << 5))
+
+/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
+#define MPS_BS		2	/* 4 MByte */
+/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */
+#define MPS_BU		3	/* R/W */
+/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */
+#define MPS_BW		0	/* 8Bit */
+/* CR register for Boot */
+#define MPS_CR_B	((FLASH_BASE0_PRELIM & 0xfff00000) + (MPS_BS << 17) + (MPS_BU << 15) + (MPS_BW << 13))
+/* CR register for non Boot */
+#define MPS_CR		((MULTI_PURPOSE_SOCKET_ADDR & 0xfff00000) + (MPS_BS << 17) + (MPS_BU << 15) + (MPS_BW << 13))
+
+
+
+
+
+
+
+
+
+
+