stv0991: Remove stv0991 board and architecture code

This architecture and related board are unmaintained currently and have
been for a long time. Remove them.

Signed-off-by: Tom Rini <trini@konsulko.com>

4 files changed, 0 insertions, 146 deletions

diff --git a/board/st/stv0991/Kconfig b/board/st/stv0991/Kconfig
deleted file mode 100644
index 007712f9c61..00000000000
--- a/board/st/stv0991/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_STV0991
-
-config SYS_BOARD
-	default "stv0991"
-
-config SYS_VENDOR
-	default "st"
-
-config SYS_SOC
-	default "stv0991"
-
-config SYS_CONFIG_NAME
-	default "stv0991"
-
-endif
diff --git a/board/st/stv0991/MAINTAINERS b/board/st/stv0991/MAINTAINERS
deleted file mode 100644
index e7a2ccaa1f2..00000000000
--- a/board/st/stv0991/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-STV0991 APPLICATION BOARD
-M:	Vikas Manocha <vikas.manocha@st.com>
-S:	Maintained
-F:	board/st/stv0991/
-F:	include/configs/stv0991.h
-F:	configs/stv0991_defconfig
diff --git a/board/st/stv0991/Makefile b/board/st/stv0991/Makefile
deleted file mode 100644
index 7f6d719c322..00000000000
--- a/board/st/stv0991/Makefile
+++ /dev/null
@@ -1,6 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2014, STMicroelectronics - All Rights Reserved
-# Author(s): Vikas Manocha, <vikas.manocha@st.com> for STMicroelectronics.
-
-obj-y	:= stv0991.o
diff --git a/board/st/stv0991/stv0991.c b/board/st/stv0991/stv0991.c
deleted file mode 100644
index 57ca9f659c1..00000000000
--- a/board/st/stv0991/stv0991.c
+++ /dev/null
@@ -1,119 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014, STMicroelectronics - All Rights Reserved
- * Author(s): Vikas Manocha, <vikas.manocha@st.com> for STMicroelectronics.
- */
-
-#include <common.h>
-#include <bootstage.h>
-#include <dm.h>
-#include <init.h>
-#include <miiphy.h>
-#include <net.h>
-#include <asm/arch/stv0991_periph.h>
-#include <asm/arch/stv0991_defs.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/gpio.h>
-#include <netdev.h>
-#include <asm/global_data.h>
-#include <asm/io.h>
-#include <dm/platform_data/serial_pl01x.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-struct gpio_regs *const gpioa_regs =
-		(struct gpio_regs *) GPIOA_BASE_ADDR;
-
-#ifndef CONFIG_OF_CONTROL
-static const struct pl01x_serial_plat serial_plat = {
-	.base = 0x80406000,
-	.type = TYPE_PL011,
-	.clock = 2700 * 1000,
-};
-
-U_BOOT_DRVINFO(stv09911_serials) = {
-	.name = "serial_pl01x",
-	.plat = &serial_plat,
-};
-#endif
-
-#if CONFIG_IS_ENABLED(BOOTSTAGE)
-void show_boot_progress(int progress)
-{
-	printf("%i\n", progress);
-}
-#endif
-
-void enable_eth_phy(void)
-{
-	/* Set GPIOA_06 pad HIGH (Appli board)*/
-	writel(readl(&gpioa_regs->dir) | 0x40, &gpioa_regs->dir);
-	writel(readl(&gpioa_regs->data) | 0x40, &gpioa_regs->data);
-}
-int board_eth_enable(void)
-{
-	stv0991_pinmux_config(ETH_GPIOB_10_31_C_0_4);
-	clock_setup(ETH_CLOCK_CFG);
-	enable_eth_phy();
-	return 0;
-}
-
-int board_qspi_enable(void)
-{
-	stv0991_pinmux_config(QSPI_CS_CLK_PAD);
-	clock_setup(QSPI_CLOCK_CFG);
-	return 0;
-}
-
-/*
- * Miscellaneous platform dependent initialisations
- */
-int board_init(void)
-{
-	board_eth_enable();
-	board_qspi_enable();
-	return 0;
-}
-
-int board_uart_init(void)
-{
-	stv0991_pinmux_config(UART_GPIOC_30_31);
-	clock_setup(UART_CLOCK_CFG);
-	return 0;
-}
-
-#ifdef CONFIG_BOARD_EARLY_INIT_F
-int board_early_init_f(void)
-{
-	board_uart_init();
-	return 0;
-}
-#endif
-
-int dram_init(void)
-{
-	gd->ram_size = PHYS_SDRAM_1_SIZE;
-	return 0;
-}
-
-int dram_init_banksize(void)
-{
-	gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
-	gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
-
-	return 0;
-}
-
-#ifdef CONFIG_CMD_NET
-int board_eth_init(struct bd_info *bis)
-{
-	int ret = 0;
-
-#if defined(CONFIG_ETH_DESIGNWARE)
-	u32 interface = PHY_INTERFACE_MODE_MII;
-	if (designware_initialize(GMAC_BASE_ADDR, interface) >= 0)
-		ret++;
-#endif
-	return ret;
-}
-#endif