pico-imx7d: Add initial support

Add the initial support for pico-imx7d board based on Wig Cheng's
source code.

Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.

For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>

6 files changed, 464 insertions, 0 deletions

diff --git a/board/technexion/pico-imx7d/Kconfig b/board/technexion/pico-imx7d/Kconfig
new file mode 100644
index 00000000000..f4ae18ca62f
--- /dev/null
+++ b/board/technexion/pico-imx7d/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_PICO_IMX7D
+
+config SYS_BOARD
+	default "pico-imx7d"
+
+config SYS_VENDOR
+	default "technexion"
+
+config SYS_SOC
+	default "mx7"
+
+config SYS_CONFIG_NAME
+	default "pico-imx7d"
+
+endif
diff --git a/board/technexion/pico-imx7d/MAINTAINERS b/board/technexion/pico-imx7d/MAINTAINERS
new file mode 100644
index 00000000000..276162a88b8
--- /dev/null
+++ b/board/technexion/pico-imx7d/MAINTAINERS
@@ -0,0 +1,7 @@
+Technexion PICO-IMX7D board
+M:	Wig Cheng <wig.cheng@technexion.com>
+M:	Vanessa Maegima <vanessa.maegima@nxp.com>
+S:	Maintained
+F:	board/technexion/pico-imx7d/
+F:	include/configs/pico-imx7d.h
+F:	configs/pico-imx7d_defconfig
diff --git a/board/technexion/pico-imx7d/Makefile b/board/technexion/pico-imx7d/Makefile
new file mode 100644
index 00000000000..42cca470a61
--- /dev/null
+++ b/board/technexion/pico-imx7d/Makefile
@@ -0,0 +1,6 @@
+# (C) Copyright 2017 NXP Semiconductors
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := pico-imx7d.o
diff --git a/board/technexion/pico-imx7d/README b/board/technexion/pico-imx7d/README
new file mode 100644
index 00000000000..a2805ee0801
--- /dev/null
+++ b/board/technexion/pico-imx7d/README
@@ -0,0 +1,49 @@
+How to update U-Boot on pico-imx7d board
+----------------------------------------
+
+Required software on the host PC:
+
+- imx_usb_loader: https://github.com/boundarydevices/imx_usb_loader
+
+Build U-Boot for pico:
+
+$ make mrproper
+$ make pico-imx7d_defconfig
+$ make
+
+This generates the U-Boot binary called u-boot.imx.
+
+Put pico board in USB download mode (refer to the PICO-iMX7D Quick Start Guide
+page 3)
+
+Connect a USB to serial adapter between the host PC and pico.
+
+Connect a USB cable between the OTG pico port and the host PC.
+
+Open a terminal program such as minicom.
+
+Copy u-boot.imx to the imx_usb_loader folder.
+
+Load u-boot.imx via USB:
+
+$ sudo ./imx_usb u-boot.imx
+
+Then U-Boot starts and its messages appear in the console program.
+
+Use the default environment variables:
+
+=> env default -f -a
+=> saveenv
+
+Run the UMS command:
+=> ums 0 mmc 0
+
+Transfer u-boot.imx to be flashed into the eMMC:
+
+$ sudo dd if=u-boot.imx of=/dev/sdX bs=1K seek=1; sync
+
+Remove power from the pico board.
+
+Put pico board into normal boot mode.
+
+Power up the board and the new updated U-Boot should boot from eMMC.
diff --git a/board/technexion/pico-imx7d/imximage.cfg b/board/technexion/pico-imx7d/imximage.cfg
new file mode 100644
index 00000000000..202956a1b0f
--- /dev/null
+++ b/board/technexion/pico-imx7d/imximage.cfg
@@ -0,0 +1,98 @@
+/*
+ * Copyright (C) 2017 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+BOOT_FROM	sd
+
+/* Secure boot support */
+#ifdef CONFIG_SECURE_BOOT
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type           Address        Value
+ *
+ * where:
+ *	Addr-type register length (1,2 or 4 bytes)
+ *	Address	  absolute address of the register
+ *	value	  value to be stored in the register
+ */
+
+DATA 4 0x30340004 0x4F400005
+/* Clear then set bit30 to ensure exit from DDR retention */
+DATA 4 0x30360388 0x40000000
+DATA 4 0x30360384 0x40000000
+
+DATA 4 0x30391000 0x00000002
+DATA 4 0x307a0000 0x01040001
+DATA 4 0x307a01a0 0x80400003
+DATA 4 0x307a01a4 0x00100020
+DATA 4 0x307a01a8 0x80100004
+DATA 4 0x307a0064 0x00400046
+DATA 4 0x307a0490 0x00000001
+DATA 4 0x307a00d0 0x00020083
+DATA 4 0x307a00d4 0x00690000
+DATA 4 0x307a00dc 0x09300004
+DATA 4 0x307a00e0 0x04080000
+DATA 4 0x307a00e4 0x00100004
+DATA 4 0x307a00f4 0x0000033f
+DATA 4 0x307a0100 0x09081109
+DATA 4 0x307a0104 0x0007020d
+DATA 4 0x307a0108 0x03040407
+DATA 4 0x307a010c 0x00002006
+DATA 4 0x307a0110 0x04020205
+DATA 4 0x307a0114 0x03030202
+DATA 4 0x307a0120 0x00000803
+DATA 4 0x307a0180 0x00800020
+DATA 4 0x307a0184 0x02000100
+DATA 4 0x307a0190 0x02098204
+DATA 4 0x307a0194 0x00030303
+DATA 4 0x307a0200 0x00000016
+DATA 4 0x307a0204 0x00080808
+DATA 4 0x307a0210 0x00000f0f
+DATA 4 0x307a0214 0x07070707
+DATA 4 0x307a0218 0x0f070707
+DATA 4 0x307a0240 0x06000604
+DATA 4 0x307a0244 0x00000001
+DATA 4 0x30391000 0x00000000
+DATA 4 0x30790000 0x17420f40
+DATA 4 0x30790004 0x10210100
+DATA 4 0x30790010 0x00060807
+DATA 4 0x307900b0 0x1010007e
+DATA 4 0x3079009c 0x00000b24
+DATA 4 0x30790020 0x08080808
+DATA 4 0x30790030 0x08080808
+DATA 4 0x30790050 0x01000010
+DATA 4 0x30790050 0x00000010
+
+DATA 4 0x307900c0 0x0e407304
+DATA 4 0x307900c0 0x0e447304
+DATA 4 0x307900c0 0x0e447306
+
+CHECK_BITS_SET 4 0x307900c4 0x1
+
+DATA 4 0x307900c0 0x0e407304
+
+DATA 4 0x30384130 0x00000000
+DATA 4 0x30340020 0x00000178
+DATA 4 0x30384130 0x00000002
+DATA 4 0x30790018 0x0000000f
+
+CHECK_BITS_SET 4 0x307a0004 0x1
diff --git a/board/technexion/pico-imx7d/pico-imx7d.c b/board/technexion/pico-imx7d/pico-imx7d.c
new file mode 100644
index 00000000000..799751d699b
--- /dev/null
+++ b/board/technexion/pico-imx7d/pico-imx7d.c
@@ -0,0 +1,289 @@
+/*
+ * Copyright (C) 2017 NXP Semiconductors
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx7-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/io.h>
+#include <common.h>
+#include <fsl_esdhc.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <mmc.h>
+#include <netdev.h>
+#include <usb.h>
+#include <power/pmic.h>
+#include <power/pfuze3000_pmic.h>
+#include "../../freescale/common/pfuze.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_DSE_3P3V_49OHM | \
+	PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU47KOHM)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
+#define ENET_PAD_CTRL_MII  (PAD_CTL_DSE_3P3V_32OHM)
+
+#define ENET_RX_PAD_CTRL  (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
+
+#define I2C_PAD_CTRL    (PAD_CTL_DSE_3P3V_32OHM | PAD_CTL_SRE_SLOW | \
+	PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PUS_PU100KOHM)
+
+#ifdef CONFIG_SYS_I2C_MXC
+#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
+/* I2C4 for PMIC */
+static struct i2c_pads_info i2c_pad_info4 = {
+	.scl = {
+		.i2c_mode = MX7D_PAD_SAI1_RX_SYNC__I2C4_SCL | PC,
+		.gpio_mode = MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16 | PC,
+		.gp = IMX_GPIO_NR(6, 16),
+	},
+	.sda = {
+		.i2c_mode = MX7D_PAD_SAI1_RX_BCLK__I2C4_SDA | PC,
+		.gpio_mode = MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17 | PC,
+		.gp = IMX_GPIO_NR(6, 17),
+	},
+};
+#endif
+
+int dram_init(void)
+{
+	gd->ram_size = PHYS_SDRAM_SIZE;
+
+	return 0;
+}
+
+#ifdef CONFIG_POWER
+#define I2C_PMIC	3
+int power_init_board(void)
+{
+	struct pmic *p;
+	int ret;
+	unsigned int reg, rev_id;
+
+	ret = power_pfuze3000_init(I2C_PMIC);
+	if (ret)
+		return ret;
+
+	p = pmic_get("PFUZE3000");
+	ret = pmic_probe(p);
+	if (ret)
+		return ret;
+
+	pmic_reg_read(p, PFUZE3000_DEVICEID, &reg);
+	pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
+	printf("PMIC:  PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
+
+	/* disable Low Power Mode during standby mode */
+	pmic_reg_read(p, PFUZE3000_LDOGCTL, &reg);
+	reg |= 0x1;
+	pmic_reg_write(p, PFUZE3000_LDOGCTL, reg);
+
+	/* SW1A/1B mode set to APS/APS */
+	reg = 0x8;
+	pmic_reg_write(p, PFUZE3000_SW1AMODE, reg);
+	pmic_reg_write(p, PFUZE3000_SW1BMODE, reg);
+
+	/* SW1A/1B standby voltage set to 1.025V */
+	reg = 0xd;
+	pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg);
+	pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg);
+
+	/* decrease SW1B normal voltage to 0.975V */
+	pmic_reg_read(p, PFUZE3000_SW1BVOLT, &reg);
+	reg &= ~0x1f;
+	reg |= PFUZE3000_SW1AB_SETP(975);
+	pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg);
+
+	return 0;
+}
+#endif
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+	MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart5_pads[] = {
+	MX7D_PAD_I2C4_SCL__UART5_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX7D_PAD_I2C4_SDA__UART5_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_emmc_pads[] = {
+	MX7D_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_SD3_DATA7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX7D_PAD_GPIO1_IO14__GPIO1_IO14 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifdef CONFIG_FEC_MXC
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX7D_PAD_SD2_CD_B__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+	MX7D_PAD_SD2_WP__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL_MII),
+	MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX7D_PAD_SD3_STROBE__GPIO6_IO10 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX7D_PAD_SD3_RESET_B__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+#define FEC1_RST_GPIO	IMX_GPIO_NR(6, 11)
+
+static void setup_iomux_fec(void)
+{
+	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
+
+	gpio_direction_output(FEC1_RST_GPIO, 0);
+	udelay(500);
+	gpio_set_value(FEC1_RST_GPIO, 1);
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_fec();
+
+	return fecmxc_initialize_multi(bis, 0,
+		CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+}
+
+static int setup_fec(void)
+{
+	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
+		= (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR;
+
+	/* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17] */
+	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
+			(IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
+			IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
+
+	return set_clk_enet(ENET_125MHz);
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	unsigned short val;
+
+	/* To enable AR8035 ouput a 125MHz clk from CLK_25M */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
+	val &= 0xffe7;
+	val |= 0x18;
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);
+
+	/* introduce tx clock delay */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
+	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
+	val |= 0x0100;
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart5_pads, ARRAY_SIZE(uart5_pads));
+}
+
+static struct fsl_esdhc_cfg usdhc_cfg[1] = {
+	{USDHC3_BASE_ADDR},
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	/* Assume uSDHC3 emmc is always present */
+	return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	imx_iomux_v3_setup_multiple_pads(
+			usdhc3_emmc_pads, ARRAY_SIZE(usdhc3_emmc_pads));
+	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+
+	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
+}
+
+int board_early_init_f(void)
+{
+	setup_iomux_uart();
+
+#ifdef CONFIG_SYS_I2C_MXC
+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info4);
+#endif
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec();
+#endif
+
+	return 0;
+}
+
+int board_late_init(void)
+{
+	struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
+
+	imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+	set_wdog_reset(wdog);
+
+	/*
+	 * Do not assert internal WDOG_RESET_B_DEB(controlled by bit 4),
+	 * since we use PMIC_PWRON to reset the board.
+	 */
+	clrsetbits_le16(&wdog->wcr, 0, 0x10);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: i.MX7D PICOSOM\n");
+
+	return 0;
+}
+
+int board_usb_phy_mode(int port)
+{
+	return USB_INIT_DEVICE;
+}