* Patches by David Müller, 12 Jun 2003:

  - rewrite of the S3C24X0 register definitions stuff
  - "driver" for the built-in S3C24X0 RTC

* Patches by Yuli Barcohen, 12 Jun 2003:
  - Add MII support and Ethernet PHY initialization for MPC8260ADS board
  - Fix incorrect SIUMCR initialisation caused by wrong Hard Reset
    configuration word supplied by FPGA on some MPC8260ADS boards

* Patch by Pantelis Antoniou, 10 Jun 2003:
  Unify status LED interface

1 files changed, 51 insertions, 33 deletions

diff --git a/board/trab/trab.c b/board/trab/trab.c
index 6c9971f3b60..dd4105d97d3 100644
--- a/board/trab/trab.c
+++ b/board/trab/trab.c
@@ -71,37 +71,39 @@ int board_init ()
 	extern int vfd_init_clocks(void);
 #endif
 	DECLARE_GLOBAL_DATA_PTR;
+	S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER();
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
 
 	/* memory and cpu-speed are setup before relocation */
 #ifdef CONFIG_TRAB_50MHZ
 	/* change the clock to be 50 MHz 1:1:1 */
 	/* MDIV:0x5c PDIV:4 SDIV:2 */
-	rMPLLCON = 0x5c042;
-	rCLKDIVN = 0;
+	clk_power->MPLLCON = 0x5c042;
+	clk_power->CLKDIVN = 0;
 #else
 	/* change the clock to be 133 MHz 1:2:4 */
 	/* MDIV:0x7d PDIV:4 SDIV:1 */
-	rMPLLCON = 0x7d041;
-	rCLKDIVN = 3;
+	clk_power->MPLLCON = 0x7d041;
+	clk_power->CLKDIVN = 3;
 #endif
 
 	/* set up the I/O ports */
-	rPACON = 0x3ffff;
-	rPBCON = 0xaaaaaaaa;
-	rPBUP  = 0xffff;
+	gpio->PACON = 0x3ffff;
+	gpio->PBCON = 0xaaaaaaaa;
+	gpio->PBUP  = 0xffff;
 	/* INPUT nCTS0 nRTS0 TXD[1] TXD[0] RXD[1] RXD[0]	*/
 	/*  00,    10,      10,      10,      10,      10,      10 	*/
-	rPFCON = (2<<0) | (2<<2) | (2<<4) | (2<<6) | (2<<8) | (2<<10);
+	gpio->PFCON = (2<<0) | (2<<2) | (2<<4) | (2<<6) | (2<<8) | (2<<10);
 #ifdef CONFIG_HWFLOW
 	/* do not pull up RXD0, RXD1, TXD0, TXD1, CTS0, RTS0 */
-	rPFUP  = (1<<0) | (1<<1) | (1<<2) | (1<<3) | (1<<4) | (1<<5);
+	gpio->PFUP  = (1<<0) | (1<<1) | (1<<2) | (1<<3) | (1<<4) | (1<<5);
 #else
 	/* do not pull up RXD0, RXD1, TXD0, TXD1 */
-	rPFUP  = (1<<0) | (1<<1) | (1<<2) | (1<<3);
+	gpio->PFUP  = (1<<0) | (1<<1) | (1<<2) | (1<<3);
 #endif
-	rPGCON = 0x0;
-	rPGUP  = 0x0;
-	rOPENCR= 0x0;
+	gpio->PGCON = 0x0;
+	gpio->PGUP  = 0x0;
+	gpio->OPENCR= 0x0;
 
 	/* arch number of SAMSUNG-Board */
 	/* MACH_TYPE_SMDK2400 */
@@ -112,8 +114,8 @@ int board_init ()
 	gd->bd->bi_boot_params = 0x0c000100;
 
 	/* Make sure both buzzers are turned off */
-	rPDCON |= 0x5400;
-	rPDDAT &= ~0xE0;
+	gpio->PDCON |= 0x5400;
+	gpio->PDDAT &= ~0xE0;
 
 #ifdef CONFIG_VFD
 	vfd_init_clocks();
@@ -305,57 +307,73 @@ static int key_pressed(void)
 
 #ifdef CFG_BRIGHTNESS
 
-#define SET_CS_TOUCH        (rPDDAT &= 0x5FF)
-#define CLR_CS_TOUCH        (rPDDAT |= 0x200)
+static inline void SET_CS_TOUCH(void)
+{
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
+	gpio->PDDAT &= 0x5FF;
+}
+
+static inline void CLR_CS_TOUCH(void)
+{
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
+	gpio->PDDAT |= 0x200;
+}
 
 static void spi_init(void)
 {
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+	S3C24X0_SPI * const spi = S3C24X0_GetBase_SPI();
 	int i;
 
 	/* Configure I/O ports. */
- 	rPDCON = (rPDCON & 0xF3FFFF) | 0x040000;
-	rPGCON = (rPGCON & 0x0F3FFF) | 0x008000;
-	rPGCON = (rPGCON & 0x0CFFFF) | 0x020000;
-	rPGCON = (rPGCON & 0x03FFFF) | 0x080000;
+ 	gpio->PDCON = (gpio->PDCON & 0xF3FFFF) | 0x040000;
+	gpio->PGCON = (gpio->PGCON & 0x0F3FFF) | 0x008000;
+	gpio->PGCON = (gpio->PGCON & 0x0CFFFF) | 0x020000;
+	gpio->PGCON = (gpio->PGCON & 0x03FFFF) | 0x080000;
 
-	CLR_CS_TOUCH;
+	CLR_CS_TOUCH();
 
-	rSPPRE = 0x1F; /* Baudrate ca. 514kHz */
-	rSPPIN = 0x01;  /* SPI-MOSI holds Level after last bit */
-	rSPCON = 0x1A;  /* Polling, Prescaler, Master, CPOL=0, CPHA=1 */
+	spi->ch[0].SPPRE = 0x1F; /* Baudrate ca. 514kHz */
+	spi->ch[0].SPPIN = 0x01;  /* SPI-MOSI holds Level after last bit */
+	spi->ch[0].SPCON = 0x1A;  /* Polling, Prescaler, Master, CPOL=0, CPHA=1 */
 
 	/* Dummy byte ensures clock to be low. */
 	for (i = 0; i < 10; i++) {
-		rSPTDAT = 0xFF;
+		spi->ch[0].SPTDAT = 0xFF;
 	}
 	wait_transmit_done();
 }
 
 static void wait_transmit_done(void)
 {
-	while (!(rSPSTA & 0x01)); /* wait until transfer is done */
+	S3C24X0_SPI * const spi = S3C24X0_GetBase_SPI();
+
+	while (!(spi->ch[0].SPSTA & 0x01)); /* wait until transfer is done */
 }
 
 static void tsc2000_write(unsigned int page, unsigned int reg,
 						  unsigned int data)
 {
+	S3C24X0_SPI * const spi = S3C24X0_GetBase_SPI();
 	unsigned int command;
 
-	SET_CS_TOUCH;
+	SET_CS_TOUCH();
 	command = 0x0000;
 	command |= (page << 11);
 	command |= (reg << 5);
 
-	rSPTDAT = (command & 0xFF00) >> 8;
+	spi->ch[0].SPTDAT = (command & 0xFF00) >> 8;
 	wait_transmit_done();
-	rSPTDAT = (command & 0x00FF);
+	spi->ch[0].SPTDAT = (command & 0x00FF);
 	wait_transmit_done();
-	rSPTDAT = (data & 0xFF00) >> 8;
+	spi->ch[0].SPTDAT = (data & 0xFF00) >> 8;
 	wait_transmit_done();
-	rSPTDAT = (data & 0x00FF);
+	spi->ch[0].SPTDAT = (data & 0x00FF);
 	wait_transmit_done();
 
-	CLR_CS_TOUCH;
+	CLR_CS_TOUCH();
 }
 
 static void tsc2000_set_brightness(void)