ppc4xx: Consolidate pci_target_init() function

This patch removes the duplicted implementations of the pci_target_init()
function by introducing a weak default function for it. This weak default
has a different implementation for 440EP(x)/GR(x) PPC's. It can be
overridden by a board specific version (e.g. PMC440, korat).

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>

22 files changed, 4 insertions, 1020 deletions

diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index 313f9f36a65..3ffdac8bd5e 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -522,67 +522,6 @@ int pci_pre_init(struct pci_controller *hose)
 #endif /* defined(CONFIG_PCI) */
 
 /*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*--------------------------------------------------------------------------+
-	 * Set up Direct MMIO registers
-	 *--------------------------------------------------------------------------*/
-	/*--------------------------------------------------------------------------+
-	  | PowerPC440 EP PCI Master configuration.
-	  | Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	  |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
-	  |   Use byte reversed out routines to handle endianess.
-	  | Make this region non-prefetchable.
-	  +--------------------------------------------------------------------------*/
-	out32r(PCIL0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 Local Address */
-	out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
-
-	out32r(PCIL0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
-	out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
-
-	out32r(PCIL0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM1LA, 0);	/* Local Addr. Reg */
-	out32r(PCIL0_PTM2MS, 0);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM2LA, 0);	/* Local Addr. Reg */
-
-	/*--------------------------------------------------------------------------+
-	 * Set up Configuration registers
-	 *--------------------------------------------------------------------------*/
-
-	/* Program the board's subsystem id/vendor id */
-	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
-			      CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
-	/* Configure command register as bus master */
-	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
-	/* 240nS PCI clock */
-	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
-	/* No error reporting */
-	pci_write_config_word(0, PCI_ERREN, 0);
-
-	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif				/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
  *  pci_master_init
  *
  ************************************************************************/
diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c
index 9a8ca8eceab..13a0daced77 100644
--- a/board/amcc/canyonlands/canyonlands.c
+++ b/board/amcc/canyonlands/canyonlands.c
@@ -326,43 +326,6 @@ phys_size_t initdram(int board_type)
 }
 #endif
 
-/*
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
-	/*
-	 * Disable everything
-	 */
-	out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
-	out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
-	out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
-	out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
-
-	/*
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
-	 * strapping options to not support sizes such as 128/256 MB.
-	 */
-	out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
-	out_le32((void *)PCIL0_PIM0LAH, 0);
-	out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-	out_le32((void *)PCIL0_BAR0, 0);
-
-	/*
-	 * Program the board's subsystem id/vendor id
-	 */
-	out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
-	out_le16((void *)PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif	/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
 #if defined(CONFIG_PCI)
 int board_pcie_first(void)
 {
diff --git a/board/amcc/ebony/ebony.c b/board/amcc/ebony/ebony.c
index 1524b5333a4..e4d168f9d84 100644
--- a/board/amcc/ebony/ebony.c
+++ b/board/amcc/ebony/ebony.c
@@ -195,42 +195,3 @@ int pci_pre_init(struct pci_controller *hose)
 	return 1;
 }
 #endif	/* defined(CONFIG_PCI) */
-
-/*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*--------------------------------------------------------------------------+
-	 * Disable everything
-	 *--------------------------------------------------------------------------*/
-	out32r(PCIL0_PIM0SA, 0);	/* disable */
-	out32r(PCIL0_PIM1SA, 0);	/* disable */
-	out32r(PCIL0_PIM2SA, 0);	/* disable */
-	out32r(PCIL0_EROMBA, 0);	/* disable expansion rom */
-
-	/*--------------------------------------------------------------------------+
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
-     * options to not support sizes such as 128/256 MB.
-	 *--------------------------------------------------------------------------*/
-	out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
-	out32r(PCIL0_PIM0LAH, 0);
-	out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-
-	out32r(PCIL0_BAR0, 0);
-
-	/*--------------------------------------------------------------------------+
-	 * Program the board's subsystem id/vendor id
-	 *--------------------------------------------------------------------------*/
-	out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
-	out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif				/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c
index f43e76448bb..f0b48c0d320 100644
--- a/board/amcc/katmai/katmai.c
+++ b/board/amcc/katmai/katmai.c
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2007-2008
+ * (C) Copyright 2007-2009
  * Stefan Roese, DENX Software Engineering, sr@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -291,44 +291,6 @@ int pci_pre_init(struct pci_controller * hose )
 }
 #endif	/* defined(CONFIG_PCI) */
 
-/*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
-	/*-------------------------------------------------------------------+
-	 * Disable everything
-	 *-------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0SA, 0 ); /* disable */
-	out32r( PCIL0_PIM1SA, 0 ); /* disable */
-	out32r( PCIL0_PIM2SA, 0 ); /* disable */
-	out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
-	/*-------------------------------------------------------------------+
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
-	 * strapping options to not support sizes such as 128/256 MB.
-	 *-------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
-	out32r( PCIL0_PIM0LAH, 0 );
-	out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-	out32r( PCIL0_BAR0, 0 );
-
-	/*-------------------------------------------------------------------+
-	 * Program the board's subsystem id/vendor id
-	 *-------------------------------------------------------------------*/
-	out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
-	out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
-	out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif	/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
 #if defined(CONFIG_PCI)
 int board_pcie_card_present(int port)
 {
diff --git a/board/amcc/luan/luan.c b/board/amcc/luan/luan.c
index 94ba6437f6d..e0b297e7072 100644
--- a/board/amcc/luan/luan.c
+++ b/board/amcc/luan/luan.c
@@ -160,46 +160,6 @@ int pci_pre_init( struct pci_controller *hose )
 
 
 /*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*--------------------------------------------------------------------------+
-	 * Disable everything
-	 *--------------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0SA, 0 ); /* disable */
-	out32r( PCIL0_PIM1SA, 0 ); /* disable */
-	out32r( PCIL0_PIM2SA, 0 ); /* disable */
-	out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
-	/*--------------------------------------------------------------------------+
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
-	 * options to not support sizes such as 128/256 MB.
-	 *--------------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
-	out32r( PCIL0_PIM0LAH, 0 );
-	out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
-	out32r( PCIL0_BAR0, 0 );
-
-	/*--------------------------------------------------------------------------+
-	 * Program the board's subsystem id/vendor id
-	 *--------------------------------------------------------------------------*/
-	out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
-	out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
-	out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-
-/*************************************************************************
  *  hw_watchdog_reset
  *
  *	This routine is called to reset (keep alive) the watchdog timer
diff --git a/board/amcc/ocotea/ocotea.c b/board/amcc/ocotea/ocotea.c
index 2f64764ee29..b38f3cc400f 100644
--- a/board/amcc/ocotea/ocotea.c
+++ b/board/amcc/ocotea/ocotea.c
@@ -307,46 +307,6 @@ int pci_pre_init(struct pci_controller * hose )
 }
 #endif /* defined(CONFIG_PCI) */
 
-/*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
-	/*--------------------------------------------------------------------------+
-	 * Disable everything
-	 *--------------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0SA, 0 ); /* disable */
-	out32r( PCIL0_PIM1SA, 0 ); /* disable */
-	out32r( PCIL0_PIM2SA, 0 ); /* disable */
-	out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
-	/*--------------------------------------------------------------------------+
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
-	 * options to not support sizes such as 128/256 MB.
-	 *--------------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
-	out32r( PCIL0_PIM0LAH, 0 );
-	out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
-	out32r( PCIL0_BAR0, 0 );
-
-	/*--------------------------------------------------------------------------+
-	 * Program the board's subsystem id/vendor id
-	 *--------------------------------------------------------------------------*/
-	out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
-	out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
-	out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-
 void fpga_init(void)
 {
 	unsigned long group;
diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c
index 43938200616..b8ef4e76337 100644
--- a/board/amcc/sequoia/sequoia.c
+++ b/board/amcc/sequoia/sequoia.c
@@ -427,71 +427,6 @@ int pci_pre_init(struct pci_controller *hose)
 }
 #endif /* defined(CONFIG_PCI) */
 
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*
-	 * Set up Direct MMIO registers
-	 */
-	/*
-	 * PowerPC440EPX PCI Master configuration.
-	 * Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	 * PLB address 0xA0000000-0xDFFFFFFF
-	 *     ==> PCI address 0xA0000000-0xDFFFFFFF
-	 * Use byte reversed out routines to handle endianess.
-	 * Make this region non-prefetchable.
-	 */
-	out32r(PCIL0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute */
-						/* - disabled b4 setting */
-	out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 Local Address */
-	out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, */
-						/* and enable region */
-
-	out32r(PCIL0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute */
-						/* - disabled b4 setting */
-	out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
-	out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, */
-						/* and enable region */
-
-	out32r(PCIL0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM1LA, 0);		/* Local Addr. Reg */
-	out32r(PCIL0_PTM2MS, 0);		/* Memory Size/Attribute */
-	out32r(PCIL0_PTM2LA, 0);		/* Local Addr. Reg */
-
-	/*
-	 * Set up Configuration registers
-	 */
-
-	/* Program the board's subsystem id/vendor id */
-	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
-			      CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
-	/* Configure command register as bus master */
-	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
-	/* 240nS PCI clock */
-	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
-	/* No error reporting */
-	pci_write_config_word(0, PCI_ERREN, 0);
-
-	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
 #if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
 void pci_master_init(struct pci_controller *hose)
 {
diff --git a/board/amcc/taishan/taishan.c b/board/amcc/taishan/taishan.c
index 81e8fe14ab8..574ff1a7bc2 100644
--- a/board/amcc/taishan/taishan.c
+++ b/board/amcc/taishan/taishan.c
@@ -240,45 +240,6 @@ int pci_pre_init(struct pci_controller * hose )
 }
 #endif /* defined(CONFIG_PCI) */
 
-/*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
-	/*--------------------------------------------------------------------------+
-	 * Disable everything
-	 *--------------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0SA, 0 ); /* disable */
-	out32r( PCIL0_PIM1SA, 0 ); /* disable */
-	out32r( PCIL0_PIM2SA, 0 ); /* disable */
-	out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
-	/*--------------------------------------------------------------------------+
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
-	 * options to not support sizes such as 128/256 MB.
-	 *--------------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
-	out32r( PCIL0_PIM0LAH, 0 );
-	out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
-	out32r( PCIL0_BAR0, 0 );
-
-	/*--------------------------------------------------------------------------+
-	 * Program the board's subsystem id/vendor id
-	 *--------------------------------------------------------------------------*/
-	out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
-	out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
-	out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
 #ifdef CONFIG_POST
 /*
  * Returns 1 if keys pressed to start the power-on long-running tests
diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c
index e416eeb1676..cd14a6a487d 100644
--- a/board/amcc/yosemite/yosemite.c
+++ b/board/amcc/yosemite/yosemite.c
@@ -408,67 +408,6 @@ int pci_pre_init(struct pci_controller *hose)
 #endif	/* defined(CONFIG_PCI) */
 
 /*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*--------------------------------------------------------------------------+
-	 * Set up Direct MMIO registers
-	 *--------------------------------------------------------------------------*/
-	/*--------------------------------------------------------------------------+
-	  | PowerPC440 EP PCI Master configuration.
-	  | Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	  |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
-	  |   Use byte reversed out routines to handle endianess.
-	  | Make this region non-prefetchable.
-	  +--------------------------------------------------------------------------*/
-	out32r(PCIL0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 Local Address */
-	out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
-
-	out32r(PCIL0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);	/* PMM0 Local Address */
-	out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
-
-	out32r(PCIL0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM1LA, 0);	/* Local Addr. Reg */
-	out32r(PCIL0_PTM2MS, 0);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM2LA, 0);	/* Local Addr. Reg */
-
-	/*--------------------------------------------------------------------------+
-	 * Set up Configuration registers
-	 *--------------------------------------------------------------------------*/
-
-	/* Program the board's subsystem id/vendor id */
-	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
-			      CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
-	/* Configure command register as bus master */
-	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
-	/* 240nS PCI clock */
-	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
-	/* No error reporting */
-	pci_write_config_word(0, PCI_ERREN, 0);
-
-	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif				/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
  *  pci_master_init
  *
  ************************************************************************/
diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
index 7315033dc89..0ec26f14d19 100644
--- a/board/amcc/yucca/yucca.c
+++ b/board/amcc/yucca/yucca.c
@@ -619,44 +619,6 @@ int pci_pre_init(struct pci_controller * hose )
 }
 #endif	/* defined(CONFIG_PCI) */
 
-/*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
-	/*-------------------------------------------------------------------+
-	 * Disable everything
-	 *-------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0SA, 0 ); /* disable */
-	out32r( PCIL0_PIM1SA, 0 ); /* disable */
-	out32r( PCIL0_PIM2SA, 0 ); /* disable */
-	out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
-	/*-------------------------------------------------------------------+
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
-	 * strapping options to not support sizes such as 128/256 MB.
-	 *-------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
-	out32r( PCIL0_PIM0LAH, 0 );
-	out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-	out32r( PCIL0_BAR0, 0 );
-
-	/*-------------------------------------------------------------------+
-	 * Program the board's subsystem id/vendor id
-	 *-------------------------------------------------------------------*/
-	out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
-	out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
-	out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif	/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
 #if defined(CONFIG_PCI)
 int board_pcie_card_present(int port)
 {
diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c
index 8f9f9500e29..866dcafcfa3 100644
--- a/board/esd/du440/du440.c
+++ b/board/esd/du440/du440.c
@@ -414,73 +414,6 @@ int pci_pre_init(struct pci_controller *hose)
 }
 #endif /* defined(CONFIG_PCI) */
 
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*
-	 * Set up Direct MMIO registers
-	 */
-	/*
-	 * PowerPC440EPX PCI Master configuration.
-	 * Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	 * PLB address 0xA0000000-0xDFFFFFFF
-	 *     ==> PCI address 0xA0000000-0xDFFFFFFF
-	 * Use byte reversed out routines to handle endianess.
-	 * Make this region non-prefetchable.
-	 */
-	out32r(PCIL0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute */
-						/* - disabled b4 setting */
-	out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 Local Address */
-	out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, */
-						/* and enable region */
-
-	out32r(PCIL0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute */
-						/* - disabled b4 setting */
-	out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
-	out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, */
-						/* and enable region */
-
-	out32r(PCIL0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM1LA, 0);		/* Local Addr. Reg */
-	out32r(PCIL0_PTM2MS, 0);		/* Memory Size/Attribute */
-	out32r(PCIL0_PTM2LA, 0);		/* Local Addr. Reg */
-
-	/*
-	 * Set up Configuration registers
-	 */
-
-	/* Program the board's subsystem id/vendor id */
-	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
-			      PCI_VENDOR_ID_ESDGMBH);
-	pci_write_config_word(0, PCI_SUBSYSTEM_ID, PCI_DEVICE_ID_DU440);
-
-	pci_write_config_word(0, PCI_CLASS_SUB_CODE, PCI_CLASS_BRIDGE_HOST);
-
-	/* Configure command register as bus master */
-	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
-	/* 240nS PCI clock */
-	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
-	/* No error reporting */
-	pci_write_config_word(0, PCI_ERREN, 0);
-
-	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
 #if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
 void pci_master_init(struct pci_controller *hose)
 {
diff --git a/board/esd/du440/du440.h b/board/esd/du440/du440.h
index a124a7ee9b5..37697ec854f 100644
--- a/board/esd/du440/du440.h
+++ b/board/esd/du440/du440.h
@@ -38,6 +38,3 @@
 #define PWR_RDY			0x10
 
 #define CPLD_IRQ		(32+30)
-
-#define PCI_VENDOR_ID_ESDGMBH	0x12fe
-#define PCI_DEVICE_ID_DU440	0x0444
diff --git a/board/gdsys/gdppc440etx/gdppc440etx.c b/board/gdsys/gdppc440etx/gdppc440etx.c
index 92f5d822f69..b93a420154f 100644
--- a/board/gdsys/gdppc440etx/gdppc440etx.c
+++ b/board/gdsys/gdppc440etx/gdppc440etx.c
@@ -217,69 +217,6 @@ int pci_pre_init(struct pci_controller *hose)
 #endif	/* defined(CONFIG_PCI) */
 
 /*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*
-	 * Set up Direct MMIO registers
-	 */
-
-	/*
-	 * PowerPC440 EP PCI Master configuration.
-	 * Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	 *       PLB address 0xA0000000-0xDFFFFFFF
-	 *   ==> PCI address 0xA0000000-0xDFFFFFFF
-	 *   Use byte reversed out routines to handle endianess.
-	 * Make this region non-prefetchable.
-	 */
-	out32r(PCIL0_PMM0MA, 0x00000000); 	/* disabled b4 setting */
-	out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);
-	out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
-	out32r(PCIL0_PMM0PCIHA, 0x00000000);
-	out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M, no prefetch, enable region */
-
-	out32r(PCIL0_PMM1MA, 0x00000000);	/* disabled b4 setting */
-	out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);
-	out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
-	out32r(PCIL0_PMM1PCIHA, 0x00000000);
-	out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M, no prefetch, enable region */
-
-	out32r(PCIL0_PTM1MS, 0x00000001);
-	out32r(PCIL0_PTM1LA, 0);
-	out32r(PCIL0_PTM2MS, 0);
-	out32r(PCIL0_PTM2LA, 0);
-
-	/*
-	 * Set up Configuration registers
-	 */
-
-	/* Program the board's subsystem id/vendor id */
-	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
-			      CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
-	/* Configure command register as bus master */
-	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
-	/* 240nS PCI clock */
-	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
-	/* No error reporting */
-	pci_write_config_word(0, PCI_ERREN, 0);
-
-	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif	/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*
  *  pci_master_init
  *
  */
diff --git a/board/gdsys/intip/intip.c b/board/gdsys/intip/intip.c
index 49d24513582..23a10c41f9f 100644
--- a/board/gdsys/intip/intip.c
+++ b/board/gdsys/intip/intip.c
@@ -141,43 +141,6 @@ int checkboard(void)
 	return 0;
 }
 
-/*
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*
-	 * Disable everything
-	 */
-	out_le32((void *)PCIL0_PIM0SA, 0); /* disable */
-	out_le32((void *)PCIL0_PIM1SA, 0); /* disable */
-	out_le32((void *)PCIL0_PIM2SA, 0); /* disable */
-	out_le32((void *)PCIL0_EROMBA, 0); /* disable expansion rom */
-
-	/*
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
-	 * strapping options to not support sizes such as 128/256 MB.
-	 */
-	out_le32((void *)PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
-	out_le32((void *)PCIL0_PIM0LAH, 0);
-	out_le32((void *)PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-	out_le32((void *)PCIL0_BAR0, 0);
-
-	/*
-	 * Program the board's subsystem id/vendor id
-	 */
-	out_le16((void *)PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	out_le16((void *)PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
-	out_le16((void *)PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif	/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
 int board_early_init_r(void)
 {
 	/*
diff --git a/board/korat/korat.c b/board/korat/korat.c
index b0e6a56a63c..02ebfdf3710 100644
--- a/board/korat/korat.c
+++ b/board/korat/korat.c
@@ -35,6 +35,7 @@
 #include <asm/io.h>
 #include <asm/ppc4xx-uic.h>
 #include <asm/processor.h>
+#include <asm/4xx_pci.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -668,60 +669,8 @@ int pci_pre_init(struct pci_controller *hose)
 #if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
 void pci_target_init(struct pci_controller *hose)
 {
-	/*
-	 * Set up Direct MMIO registers
-	 */
-	/*
-	 * PowerPC440EPX PCI Master configuration.
-	 * Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	 * PLB address 0x80000000-0xBFFFFFFF
-	 *     ==> PCI address 0x80000000-0xBFFFFFFF
-	 * Use byte reversed out routines to handle endianess.
-	 * Make this region non-prefetchable.
-	 */
-	out32r(PCIL0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute */
-						/* - disabled b4 setting */
-	out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 Local Address */
-	out32r(PCIL0_PMM0PCILA,
-	       CONFIG_SYS_PCI_MEMBASE);		/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, */
-						/* and enable region */
-
-	out32r(PCIL0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute */
-						/* - disabled b4 setting */
-	out32r(PCIL0_PMM1LA,
-	       CONFIG_SYS_PCI_MEMBASE + 0x20000000);	/* PMM0 Local Address */
-	out32r(PCIL0_PMM1PCILA,
-	       CONFIG_SYS_PCI_MEMBASE + 0x20000000);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, */
-						/* and enable region */
-
-	out32r(PCIL0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM1LA, 0);		/* Local Addr. Reg */
-	out32r(PCIL0_PTM2MS, 0);		/* Memory Size/Attribute */
-	out32r(PCIL0_PTM2LA, 0);		/* Local Addr. Reg */
-
-	/*
-	 * Set up Configuration registers
-	 */
-
-	/* Program the board's subsystem id/vendor id */
-	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
-			      CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
-	/* Configure command register as bus master */
-	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
-	/* 240nS PCI clock */
-	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
-	/* No error reporting */
-	pci_write_config_word(0, PCI_ERREN, 0);
-
-	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
+	/* First do 440EP(x) common setup */
+	__pci_target_init(hose);
 
 	/*
 	 * Set up Configuration registers for on-board NEC uPD720101 USB
diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c
index 09ba2b933d6..77f2d7f688f 100644
--- a/board/lwmon5/lwmon5.c
+++ b/board/lwmon5/lwmon5.c
@@ -331,67 +331,6 @@ int pci_pre_init(struct pci_controller *hose)
 #endif	/* defined(CONFIG_PCI) */
 
 /*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*--------------------------------------------------------------------------+
-	 * Set up Direct MMIO registers
-	 *--------------------------------------------------------------------------*/
-	/*--------------------------------------------------------------------------+
-	  | PowerPC440EPX PCI Master configuration.
-	  | Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	  |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
-	  |   Use byte reversed out routines to handle endianess.
-	  | Make this region non-prefetchable.
-	  +--------------------------------------------------------------------------*/
-	out32r(PCIL0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 Local Address */
-	out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
-
-	out32r(PCIL0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
-	out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
-
-	out32r(PCIL0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM1LA, 0);	/* Local Addr. Reg */
-	out32r(PCIL0_PTM2MS, 0);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM2LA, 0);	/* Local Addr. Reg */
-
-	/*--------------------------------------------------------------------------+
-	 * Set up Configuration registers
-	 *--------------------------------------------------------------------------*/
-
-	/* Program the board's subsystem id/vendor id */
-	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
-			      CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
-	/* Configure command register as bus master */
-	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
-	/* 240nS PCI clock */
-	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
-	/* No error reporting */
-	pci_write_config_word(0, PCI_ERREN, 0);
-
-	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif				/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
  *  pci_master_init
  *
  ************************************************************************/
diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c
index 7ffc2620245..144fdd97047 100644
--- a/board/netstal/hcu5/hcu5.c
+++ b/board/netstal/hcu5/hcu5.c
@@ -377,71 +377,6 @@ int pci_pre_init(struct pci_controller *hose)
 }
 
 /*
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- */
-void pci_target_init(struct pci_controller *hose)
-{
-	if (!board_with_pci()) { return; }
-	/*
-	 * Set up Direct MMIO registers
-	 *
-	 * PowerPC440EPX PCI Master configuration.
-	 * Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	 *   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address
-	 *		  0xA0000000-0xDFFFFFFF
-	 *   Use byte reversed out routines to handle endianess.
-	 * Make this region non-prefetchable.
-	 */
-	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIL0_PMM0MA, 0x00000000);
-	out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 Local Address */
-	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);
-	out32r(PCIL0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	/* 512M + No prefetching, and enable region */
-	out32r(PCIL0_PMM0MA, 0xE0000001);
-
-	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIL0_PMM1MA, 0x00000000);
-	out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);	/* PMM0 Local Address */
-	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);
-	out32r(PCIL0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	/* 512M + No prefetching, and enable region */
-	out32r(PCIL0_PMM1MA, 0xE0000001);
-
-	out32r(PCIL0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM1LA, 0);	/* Local Addr. Reg */
-	out32r(PCIL0_PTM2MS, 0);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM2LA, 0);	/* Local Addr. Reg */
-
-	/*
-	 * Set up Configuration registers
-	 */
-
-	/* Program the board's subsystem id/vendor id */
-	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
-			      CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
-	/* Configure command register as bus master */
-	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
-	/* 240nS PCI clock */
-	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
-	/* No error reporting */
-	pci_write_config_word(0, PCI_ERREN, 0);
-
-	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-}
-
-/*
  *  pci_master_init
  *
  */
diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c
index 2155711d6f8..929375987cc 100644
--- a/board/pcs440ep/pcs440ep.c
+++ b/board/pcs440ep/pcs440ep.c
@@ -606,67 +606,6 @@ int pci_pre_init(struct pci_controller *hose)
 #endif	/* defined(CONFIG_PCI) */
 
 /*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*--------------------------------------------------------------------------+
-	 * Set up Direct MMIO registers
-	 *--------------------------------------------------------------------------*/
-	/*--------------------------------------------------------------------------+
-	  | PowerPC440 EP PCI Master configuration.
-	  | Map one 1Gig range of PLB/processor addresses to PCI memory space.
-	  |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
-	  |   Use byte reversed out routines to handle endianess.
-	  | Make this region non-prefetchable.
-	  +--------------------------------------------------------------------------*/
-	out32r(PCIL0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 Local Address */
-	out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
-
-	out32r(PCIL0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
-	out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2);	/* PMM0 Local Address */
-	out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2);	/* PMM0 PCI Low Address */
-	out32r(PCIL0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
-	out32r(PCIL0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
-
-	out32r(PCIL0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM1LA, 0);	/* Local Addr. Reg */
-	out32r(PCIL0_PTM2MS, 0);	/* Memory Size/Attribute */
-	out32r(PCIL0_PTM2LA, 0);	/* Local Addr. Reg */
-
-	/*--------------------------------------------------------------------------+
-	 * Set up Configuration registers
-	 *--------------------------------------------------------------------------*/
-
-	/* Program the board's subsystem id/vendor id */
-	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
-			      CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
-	/* Configure command register as bus master */
-	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
-	/* 240nS PCI clock */
-	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
-	/* No error reporting */
-	pci_write_config_word(0, PCI_ERREN, 0);
-
-	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif				/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
  *  pci_master_init
  *
  ************************************************************************/
diff --git a/board/prodrive/alpr/alpr.c b/board/prodrive/alpr/alpr.c
index e9e2bf3e0ba..c06aadb4141 100644
--- a/board/prodrive/alpr/alpr.c
+++ b/board/prodrive/alpr/alpr.c
@@ -179,45 +179,6 @@ int pci_pre_init(struct pci_controller * hose )
 #endif /* defined(CONFIG_PCI) */
 
 /*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
-	/*--------------------------------------------------------------------------+
-	 * Disable everything
-	 *--------------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0SA, 0 ); /* disable */
-	out32r( PCIL0_PIM1SA, 0 ); /* disable */
-	out32r( PCIL0_PIM2SA, 0 ); /* disable */
-	out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
-	/*--------------------------------------------------------------------------+
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
-	 * options to not support sizes such as 128/256 MB.
-	 *--------------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
-	out32r( PCIL0_PIM0LAH, 0 );
-	out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
-	out32r( PCIL0_BAR0, 0 );
-
-	/*--------------------------------------------------------------------------+
-	 * Program the board's subsystem id/vendor id
-	 *--------------------------------------------------------------------------*/
-	out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
-	out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
-	out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
  * Override weak is_pci_host()
  *
  *	This routine is called to determine if a pci scan should be
diff --git a/board/prodrive/p3p440/p3p440.c b/board/prodrive/p3p440/p3p440.c
index e07400794b0..5761e708454 100644
--- a/board/prodrive/p3p440/p3p440.c
+++ b/board/prodrive/p3p440/p3p440.c
@@ -196,45 +196,6 @@ int pci_pre_init(struct pci_controller *hose)
 #endif	/* defined(CONFIG_PCI) */
 
 /*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
-	/*--------------------------------------------------------------------------+
-	 * Disable everything
-	 *--------------------------------------------------------------------------*/
-	out32r(PCIL0_PIM0SA, 0);	/* disable */
-	out32r(PCIL0_PIM1SA, 0);	/* disable */
-	out32r(PCIL0_PIM2SA, 0);	/* disable */
-	out32r(PCIL0_EROMBA, 0);	/* disable expansion rom */
-
-	/*--------------------------------------------------------------------------+
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
-	 * options to not support sizes such as 128/256 MB.
-	 *--------------------------------------------------------------------------*/
-	out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
-	out32r(PCIL0_PIM0LAH, 0);
-	out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-
-	out32r(PCIL0_BAR0, 0);
-
-	/*--------------------------------------------------------------------------+
-	 * Program the board's subsystem id/vendor id
-	 *--------------------------------------------------------------------------*/
-	out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
-	out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif				/* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-/*************************************************************************
  * Override weak is_pci_host()
  *
  *	This routine is called to determine if a pci scan should be
diff --git a/board/sandburst/common/sb_common.c b/board/sandburst/common/sb_common.c
index 5749084583c..45e9043851e 100644
--- a/board/sandburst/common/sb_common.c
+++ b/board/sandburst/common/sb_common.c
@@ -333,46 +333,6 @@ int pci_pre_init(struct pci_controller * hose )
 #endif /* defined(CONFIG_PCI) */
 
 /*************************************************************************
- *  pci_target_init
- *
- *	The bootstrap configuration provides default settings for the pci
- *	inbound map (PIM). But the bootstrap config choices are limited and
- *	may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
-	/*--------------------------------------------------------------------------+
-	 * Disable everything
-	 *--------------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0SA, 0 ); /* disable */
-	out32r( PCIL0_PIM1SA, 0 ); /* disable */
-	out32r( PCIL0_PIM2SA, 0 ); /* disable */
-	out32r( PCIL0_EROMBA, 0 ); /* disable expansion rom */
-
-	/*--------------------------------------------------------------------------+
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
-	 * options to not support sizes such as 128/256 MB.
-	 *--------------------------------------------------------------------------*/
-	out32r( PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE );
-	out32r( PCIL0_PIM0LAH, 0 );
-	out32r( PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
-	out32r( PCIL0_BAR0, 0 );
-
-	/*--------------------------------------------------------------------------+
-	 * Program the board's subsystem id/vendor id
-	 *--------------------------------------------------------------------------*/
-	out16r( PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID );
-	out16r( PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID );
-
-	out16r( PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-
-/*************************************************************************
  *  board_get_enetaddr
  *
  *  Get the ethernet MAC address for the management ethernet from the
diff --git a/board/xes/xpedite1000/xpedite1000.c b/board/xes/xpedite1000/xpedite1000.c
index 0c4cf9463fa..db37ca0516a 100644
--- a/board/xes/xpedite1000/xpedite1000.c
+++ b/board/xes/xpedite1000/xpedite1000.c
@@ -166,38 +166,6 @@ int pci_pre_init(struct pci_controller * hose)
 }
 #endif /* defined(CONFIG_PCI) */
 
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-/*
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-void pci_target_init(struct pci_controller * hose)
-{
-	/* Disable everything */
-	out32r(PCIL0_PIM0SA, 0);
-	out32r(PCIL0_PIM1SA, 0);
-	out32r(PCIL0_PIM2SA, 0);
-	out32r(PCIL0_EROMBA, 0); /* disable expansion rom */
-
-	/*
-	 * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440 strapping
-	 * options to not support sizes such as 128/256 MB.
-	 */
-	out32r(PCIL0_PIM0LAL, CONFIG_SYS_SDRAM_BASE);
-	out32r(PCIL0_PIM0LAH, 0);
-	out32r(PCIL0_PIM0SA, ~(gd->ram_size - 1) | 1);
-
-	out32r(PCIL0_BAR0, 0);
-
-	/* Program the board's subsystem id/vendor id */
-	out16r(PCIL0_SBSYSVID, CONFIG_SYS_PCI_SUBSYS_VENDORID);
-	out16r(PCIL0_SBSYSID, CONFIG_SYS_PCI_SUBSYS_DEVICEID);
-
-	out16r(PCIL0_CMD, in16r(PCIL0_CMD) | PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
 #if defined(CONFIG_PCI)
 /*
  * Override weak is_pci_host()