ARM: imx: vining2000: Convert MMC and block to DM

Enable DM block and DM MMC support on iMX6SX VINING|2000 .
Convert board code to match the DM support. This disables
USB mass storage support due to missing DM USB, however
that will be re-enabled in subsequent patch.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>

1 files changed, 0 insertions, 77 deletions

diff --git a/board/softing/vining_2000/vining_2000.c b/board/softing/vining_2000/vining_2000.c
index f0313b06fbf..9ab7fbeddf0 100644
--- a/board/softing/vining_2000/vining_2000.c
+++ b/board/softing/vining_2000/vining_2000.c
@@ -76,30 +76,6 @@ static iomux_v3_cfg_t const uart1_pads[] = {
 	MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
 };
 
-static iomux_v3_cfg_t const usdhc2_pads[] = {
-	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
-	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_LCD1_VSYNC__GPIO3_IO_28 | MUX_PAD_CTRL(GPIO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const usdhc4_pads[] = {
-	MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_CLK_PAD_CTRL),
-	MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD4_RESET_B__USDHC4_RESET_B | MUX_PAD_CTRL(USDHC_RESET_CTRL),
-};
-
 static iomux_v3_cfg_t const fec1_pads[] = {
 	MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
 	MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
@@ -449,59 +425,6 @@ int board_early_init_f(void)
 	return 0;
 }
 
-static struct fsl_esdhc_cfg usdhc_cfg[2] = {
-	{USDHC4_BASE_ADDR, 0, 8},
-	{USDHC2_BASE_ADDR, 0, 4},
-};
-
-#define USDHC2_CD_GPIO IMX_GPIO_NR(3, 28)
-
-int board_mmc_getcd(struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-
-	if (cfg->esdhc_base == USDHC4_BASE_ADDR)
-		return 1;
-	if (cfg->esdhc_base == USDHC2_BASE_ADDR)
-		return !gpio_get_value(USDHC2_CD_GPIO);
-
-	return -EINVAL;
-}
-
-int board_mmc_init(bd_t *bis)
-{
-	int ret;
-
-	/*
-	 * According to the board_mmc_init() the following map is done:
-	 * (U-Boot device node)    (Physical Port)
-	 * mmc0                    USDHC4
-	 * mmc1                    USDHC2
-	 */
-	imx_iomux_v3_setup_multiple_pads(
-		usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
-	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
-
-	imx_iomux_v3_setup_multiple_pads(
-		usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-	gpio_direction_input(USDHC2_CD_GPIO);
-	usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-
-	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-	if (ret) {
-		printf("Warning: failed to initialize USDHC4\n");
-		return ret;
-	}
-
-	ret = fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
-	if (ret) {
-		printf("Warning: failed to initialize USDHC2\n");
-		return ret;
-	}
-
-	return 0;
-}
-
 int board_init(void)
 {
 	/* Address of boot parameters */