Merge branch 'next'

2 files changed, 171 insertions, 0 deletions

diff --git a/doc/README.kmeter1 b/doc/README.kmeter1
new file mode 100644
index 00000000000..44ebb7a7811
--- /dev/null
+++ b/doc/README.kmeter1
@@ -0,0 +1,91 @@
+Keymile kmeter1 Board
+-----------------------------------------
+1.	Alternative Boot EEPROM
+
+    Upon the kmeter1 startup the I2C_1 controller is used to fetch the boot
+    configuration from a serial EEPROM. During the development and debugging
+    phase it might be helpful to apply an alternative boot configuration in
+    a simple way. Therefore it is an alternative boot eeprom on the PIGGY,
+    which can be activated by setting the "ST" jumper on the PIGGY board.
+
+2.	Memory Map
+
+    BaseAddr    PortSz  Size  Device
+    ----------- ------  -----  ------
+    0x0000_0000 64 bit  256MB  DDR
+    0x8000_0000  8 bit  256KB  GPIO/PIGGY on CS1
+    0xa000_0000  8 bit  256MB  PAXE on CS3
+    0xe000_0000           2MB  Int Mem Reg Space
+    0xf000_0000 16 bit  256MB  FLASH on CS0
+
+
+    DDR-SDRAM:
+    The current realization is made with four 16-bits memory devices.
+    Mounting options have been foreseen for device architectures from
+    4Mx16 to 512Mx16. The kmeter1 is equipped with four 32Mx16 devices
+    thus resulting in a total capacity of 256MBytes.
+
+3. Compilation
+
+	Assuming you're using BASH shell:
+
+		export CROSS_COMPILE=your-cross-compile-prefix
+		cd u-boot
+		make distclean
+		make kmeter1_config
+		make
+
+4. Downloading and Flashing Images
+
+4.0 Download over serial line using Kermit:
+
+	loadb
+	[Drop to kermit:
+	    ^\c
+	    send <u-boot-bin-image>
+	    c
+	]
+
+
+    Or via tftp:
+
+	tftp 10000 u-boot.bin
+    => run load
+    Using FSL UEC0 device
+    TFTP from server 192.168.1.1; our IP address is 192.168.205.4
+    Filename '/tftpboot/kmeter1/u-boot.bin'.
+    Load address: 0x200000
+    Loading: ##############
+    done
+    Bytes transferred = 204204 (31dac hex)
+    =>
+
+4.1 Reflash U-boot Image using U-boot
+
+    => run update
+    ..... done
+    Un-Protected 5 sectors
+
+    ..... done
+    Erased 5 sectors
+    Copy to Flash... done
+    ..... done
+    Protected 5 sectors
+    Total of 204204 bytes were the same
+    Saving Environment to Flash...
+    . done
+    Un-Protected 1 sectors
+    . done
+    Un-Protected 1 sectors
+    Erasing Flash...
+    . done
+    Erased 1 sectors
+    Writing to Flash... done
+    . done
+    Protected 1 sectors
+    . done
+    Protected 1 sectors
+    =>
+
+5. Notes
+	1) The console baudrate for kmeter1 is 115200bps.
diff --git a/doc/README.simpc8313 b/doc/README.simpc8313
new file mode 100644
index 00000000000..b362c6aeea0
--- /dev/null
+++ b/doc/README.simpc8313
@@ -0,0 +1,80 @@
+Sheldon Instruments SIMPC8313 Board
+-----------------------------------------
+
+1.	Board Switches and Jumpers
+
+	S2 is used to set CFG_RESET_SOURCE.
+
+	To boot the image in Large page NAND flash, use these DIP
+	switch settings for S2:
+
+	+----------+ ON
+	| * * **** |
+	|  * *     |
+	+----------+
+	  12345678
+
+	To boot the image in Small page NAND flash, use these DIP
+	switch settings for S2:
+
+	+----------+ ON
+	| *** **** |
+	|    *     |
+	+----------+
+	  12345678
+	(where the '*' indicates the position of the tab of the switch.)
+
+2.	Memory Map
+	The memory map looks like this:
+
+	0x0000_0000	0x1fff_ffff	DDR			512M
+	0x8000_0000	0x8fff_ffff	PCI MEM			256M
+	0x9000_0000	0x9fff_ffff	PCI_MMIO		256M
+	0xe000_0000	0xe00f_ffff	IMMR			1M
+	0xe200_0000	0xe20f_ffff	PCI IO			16M
+	0xe280_0000	0xe280_7fff	NAND FLASH (CS0)	32K
+	or
+	0xe280_0000	0xe281_ffff	NAND FLASH (CS0)	128K
+	0xff00_0000	0xff00_7fff	FPGA (CS1)		1M
+
+3.	Compilation
+
+	Assuming you're using BASH (or similar) as your shell:
+
+	export CROSS_COMPILE=your-cross-compiler-prefix-
+	make distclean
+	make SIMPC8313_LP_config
+	(or make SIMPC8313_SP_config, depending on the page size
+	of your NAND flash)
+	make
+
+4.	Downloading and Flashing Images
+
+4.1	Reflash U-boot Image using U-boot
+
+	=>run update_uboot
+
+	You may want to try
+	=>tftp $loadaddr $uboot
+	first, to make sure that the TFTP load will succeed before it
+	goes ahead and wipes out your current firmware.  And of course,
+	if the new u-boot doesn't boot, you can plug the board into
+	your PCI slot and with the supplied driver and sample app
+	you can reburn a working u-boot.
+
+4.2	Downloading and Booting Linux Kernel
+
+	Ensure that all networking-related environment variables are set
+	properly (including ipaddr, serverip, gatewayip (if needed),
+	netmask, ethaddr, eth1addr, fdtfile, and bootfile).
+
+	=>tftp $loadaddr uImage
+	=>nand write $loadaddr kernel $filesize
+	=>tftp $loadaddr $fdtfile
+	=>nand write $loadaddr 7e0000 1800
+
+	=>boot
+
+5	Notes
+
+	The console baudrate for SIMPC8313 is 115200bps.