bus: uniphier-system-bus: move hardware init from board files

Move the bus initialization code to this driver from board files.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

1 files changed, 86 insertions, 0 deletions

diff --git a/drivers/bus/uniphier-system-bus.c b/drivers/bus/uniphier-system-bus.c
index c61d795bac3..ea08d66a070 100644
--- a/drivers/bus/uniphier-system-bus.c
+++ b/drivers/bus/uniphier-system-bus.c
@@ -1,7 +1,92 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 
+#include <linux/bitops.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/sizes.h>
+#include <linux/types.h>
 #include <dm.h>
 
+/* System Bus Controller registers */
+#define UNIPHIER_SBC_BASE	0x100	/* base address of bank0 space */
+#define    UNIPHIER_SBC_BASE_BE		BIT(0)	/* bank_enable */
+#define UNIPHIER_SBC_CTRL0	0x200	/* timing parameter 0 of bank0 */
+#define UNIPHIER_SBC_CTRL1	0x204	/* timing parameter 1 of bank0 */
+#define UNIPHIER_SBC_CTRL2	0x208	/* timing parameter 2 of bank0 */
+#define UNIPHIER_SBC_CTRL3	0x20c	/* timing parameter 3 of bank0 */
+#define UNIPHIER_SBC_CTRL4	0x300	/* timing parameter 4 of bank0 */
+
+#define UNIPHIER_SBC_STRIDE	0x10	/* register stride to next bank */
+
+#if 1
+/* slower but LED works */
+#define SBCTRL0_VALUE	0x55450000
+#define SBCTRL1_VALUE	0x07168d00
+#define SBCTRL2_VALUE	0x34000009
+#define SBCTRL4_VALUE	0x02110110
+
+#else
+/* faster but LED does not work */
+#define SBCTRL0_VALUE	0x55450000
+#define SBCTRL1_VALUE	0x06057700
+/* NOR flash needs more wait counts than SRAM */
+#define SBCTRL2_VALUE	0x34000009
+#define SBCTRL4_VALUE	0x02110210
+#endif
+
+void uniphier_system_bus_set_reg(void __iomem *membase)
+{
+	void __iomem *bank0_base = membase;
+	void __iomem *bank1_base = membase + UNIPHIER_SBC_STRIDE;
+
+	/*
+	 * Only CS1 is connected to support card.
+	 * BKSZ[1:0] should be set to "01".
+	 */
+	writel(SBCTRL0_VALUE, bank1_base + UNIPHIER_SBC_CTRL0);
+	writel(SBCTRL1_VALUE, bank1_base + UNIPHIER_SBC_CTRL1);
+	writel(SBCTRL2_VALUE, bank1_base + UNIPHIER_SBC_CTRL2);
+	writel(SBCTRL4_VALUE, bank1_base + UNIPHIER_SBC_CTRL4);
+
+	if (readl(bank1_base + UNIPHIER_SBC_BASE) & UNIPHIER_SBC_BASE_BE) {
+		/*
+		 * Boot Swap On: boot from external NOR/SRAM
+		 * 0x42000000-0x43ffffff is a mirror of 0x40000000-0x41ffffff.
+		 *
+		 * 0x40000000-0x41efffff, 0x42000000-0x43efffff: memory bank
+		 * 0x41f00000-0x41ffffff, 0x43f00000-0x43ffffff: peripherals
+		 */
+		writel(0x0000bc01, bank0_base + UNIPHIER_SBC_BASE);
+	} else {
+		/*
+		 * Boot Swap Off: boot from mask ROM
+		 * 0x40000000-0x41ffffff: mask ROM
+		 * 0x42000000-0x43efffff: memory bank (31MB)
+		 * 0x43f00000-0x43ffffff: peripherals (1MB)
+		 */
+		writel(0x0000be01, bank0_base + UNIPHIER_SBC_BASE); /* dummy */
+		writel(0x0200be01, bank0_base + UNIPHIER_SBC_BASE);
+	}
+}
+
+static int uniphier_system_bus_probe(struct udevice *dev)
+{
+	fdt_addr_t base;
+	void __iomem *membase;
+
+	base = dev_read_addr(dev);
+	if (base == FDT_ADDR_T_NONE)
+		return -EINVAL;
+
+	membase = devm_ioremap(dev, base, SZ_1K);
+	if (!membase)
+		return -ENOMEM;
+
+	uniphier_system_bus_set_reg(membase);
+
+	return 0;
+}
+
 static const struct udevice_id uniphier_system_bus_match[] = {
 	{ .compatible = "socionext,uniphier-system-bus" },
 	{ /* sentinel */ }
@@ -11,4 +96,5 @@ U_BOOT_DRIVER(uniphier_system_bus_driver) = {
 	.name	= "uniphier-system-bus",
 	.id	= UCLASS_SIMPLE_BUS,
 	.of_match = uniphier_system_bus_match,
+	.probe = uniphier_system_bus_probe,
 };