arm: Remove unused ST-Ericsson u8500 arch

This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.

Please note that this patch also removes these config options:

- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT

As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.

If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>

1 files changed, 0 insertions, 178 deletions

diff --git a/drivers/i2c/u8500_i2c.h b/drivers/i2c/u8500_i2c.h
deleted file mode 100644
index ceecdeede03..00000000000
--- a/drivers/i2c/u8500_i2c.h
+++ /dev/null
@@ -1,178 +0,0 @@
-/*
- * Copyright (C) ST-Ericsson SA 2009
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _U8500_I2C_H_
-#define _U8500_I2C_H_
-
-#include <asm/types.h>
-#include <asm/io.h>
-#include <asm/errno.h>
-#include <asm/arch/u8500.h>
-
-struct u8500_i2c_regs {
-	u32 cr;			/* Control Register                      0x00 */
-	u32 scr;		/* Slave Address Register                0x04 */
-	u32 hsmcr;		/* HS Master code Register               0x08 */
-	u32 mcr;		/* Master Control Register               0x0C */
-	u32 tfr;		/* Transmit Fifo Register                0x10 */
-	u32 sr;			/* Status Register                       0x14 */
-	u32 rfr;		/* Receiver Fifo Register                0x18 */
-	u32 tftr;		/* Transmit Fifo Threshold Register      0x1C */
-	u32 rftr;		/* Receiver Fifo Threshold Register      0x20 */
-	u32 dmar;		/* DMA register                          0x24 */
-	u32 brcr;		/* Baud Rate Counter Register            0x28 */
-	u32 imscr;		/* Interrupt Mask Set and Clear Register 0x2C */
-	u32 risr;		/* Raw interrupt status register         0x30 */
-	u32 misr;		/* Masked interrupt status register      0x34 */
-	u32 icr;		/* Interrupt Set and Clear Register      0x38 */
-	u32 reserved_1[(0xFE0 - 0x3c) >> 2];	/* Reserved 0x03C to 0xFE0 */
-	u32 periph_id_0;	/* peripheral ID 0			0xFE0 */
-	u32 periph_id_1;	/* peripheral ID 1			0xFE4 */
-	u32 periph_id_2;	/* peripheral ID 2			0xFE8 */
-	u32 periph_id_3;	/* peripheral ID 3			0xFEC */
-	u32 cell_id_0;		/* I2C cell   ID 0			0xFF0 */
-	u32 cell_id_1;		/* I2C cell   ID 1			0xFF4 */
-	u32 cell_id_2;		/* I2C cell   ID 2			0xFF8 */
-	u32 cell_id_3;		/* I2C cell   ID 3			0xFFC */
-};
-
-
-/* Control Register */
-
-/* Mask values for control register mask */
-#define U8500_I2C_CR_PE          0x0001	/* Peripheral enable */
-#define U8500_I2C_CR_OM          0x0006	/* Operation mode */
-#define U8500_I2C_CR_SAM         0x0008	/* Slave Addressing mode */
-#define U8500_I2C_CR_SM          0x0030	/* Speed mode */
-#define U8500_I2C_CR_SGCM        0x0040	/* Slave General call mode */
-#define U8500_I2C_CR_FTX         0x0080	/* Flush Transmit */
-#define U8500_I2C_CR_FRX         0x0100	/* Flush Receive */
-#define U8500_I2C_CR_DMA_TX_EN   0x0200	/* DMA TX Enable */
-#define U8500_I2C_CR_DMA_RX_EN   0x0400	/* DMA Rx Enable */
-#define U8500_I2C_CR_DMA_SLE     0x0800	/* DMA Synchronization Logic enable */
-#define U8500_I2C_CR_LM          0x1000	/* Loop back mode */
-#define U8500_I2C_CR_FON         0x6000	/* Filtering On */
-
-/* shift valus for control register bit fields */
-#define U8500_I2C_CR_SHIFT_PE		0	/* Peripheral enable */
-#define U8500_I2C_CR_SHIFT_OM		1	/* Operation mode */
-#define U8500_I2C_CR_SHIFT_SAM		3	/* Slave Addressing mode */
-#define U8500_I2C_CR_SHIFT_SM		4	/* Speed mode */
-#define U8500_I2C_CR_SHIFT_SGCM		6	/* Slave General call mode */
-#define U8500_I2C_CR_SHIFT_FTX		7	/* Flush Transmit */
-#define U8500_I2C_CR_SHIFT_FRX		8	/* Flush Receive */
-#define U8500_I2C_CR_SHIFT_DMA_TX_EN	9	/* DMA TX Enable */
-#define U8500_I2C_CR_SHIFT_DMA_RX_EN	10	/* DMA Rx Enable */
-#define U8500_I2C_CR_SHIFT_DMA_SLE	11	/* DMA Synch Logic enable */
-#define U8500_I2C_CR_SHIFT_LM		12	/* Loop back mode */
-#define U8500_I2C_CR_SHIFT_FON		13	/* Filtering On */
-
-/* bus operation modes */
-#define U8500_I2C_BUS_SLAVE_MODE		0
-#define U8500_I2C_BUS_MASTER_MODE		1
-#define U8500_I2C_BUS_MASTER_SLAVE_MODE	2
-
-
-/* Slave control register*/
-
-/* Mask values slave control register */
-#define U8500_I2C_SCR_ADDR                   0x3FF
-#define U8500_I2C_SCR_DATA_SETUP_TIME        0xFFFF0000
-
-/* Shift values for Slave control register */
-#define U8500_I2C_SCR_SHIFT_ADDR               0
-#define U8500_I2C_SCR_SHIFT_DATA_SETUP_TIME    16
-
-
-/* Master Control Register */
-
-/* Mask values for Master control register */
-#define U8500_I2C_MCR_OP	0x00000001	/* Operation */
-#define U8500_I2C_MCR_A7	0x000000FE	/* LSB bits of Address */
-#define U8500_I2C_MCR_EA10	0x00000700	/* Extended Address */
-#define U8500_I2C_MCR_SB	0x00000800	/* Start byte procedure */
-#define U8500_I2C_MCR_AM	0x00003000	/* Address type */
-#define U8500_I2C_MCR_STOP	0x00004000	/* stop condition */
-#define U8500_I2C_MCR_LENGTH	0x03FF8000	/* Frame length */
-#define U8500_I2C_MCR_A10	0x000007FE	/* Enable 10 bit address */
-/* mask for length field,stop and operation  */
-#define U8500_I2C_MCR_LENGTH_STOP_OP	0x3FFC001
-
-/* Shift values for Master control values */
-#define U8500_I2C_MCR_SHIFT_OP		0	/* Operation */
-#define U8500_I2C_MCR_SHIFT_A7		1	/* LSB bits of Address */
-#define U8500_I2C_MCR_SHIFT_EA10	8	/* Extended Address */
-#define U8500_I2C_MCR_SHIFT_SB		11	/* Start byte procedure */
-#define U8500_I2C_MCR_SHIFT_AM		12	/* Address type */
-#define U8500_I2C_MCR_SHIFT_STOP	14	/* stop condition */
-#define U8500_I2C_MCR_SHIFT_LENGTH	15	/* Frame length */
-#define U8500_I2C_MCR_SHIFT_A10		1	/* Enable 10 bit address */
-
-#define U8500_I2C_MCR_SHIFT_LENGTH_STOP_OP	0
-
-
-/* Status Register */
-
-/* Mask values for Status register */
-#define U8500_I2C_SR_OP	0x00000003	/* Operation */
-#define U8500_I2C_SR_STATUS	0x0000000C	/* Controller Status */
-#define U8500_I2C_SR_CAUSE	0x00000070	/* Abort Cause */
-#define U8500_I2C_SR_TYPE	0x00000180	/* Receive Type */
-#define U8500_I2C_SR_LENGTH	0x000FF700	/* Transfer length */
-
-/* Shift values for Status register */
-#define U8500_I2C_SR_SHIFT_OP		0	/* Operation */
-#define U8500_I2C_SR_SHIFT_STATUS	2	/* Controller Status */
-#define U8500_I2C_SR_SHIFT_CAUSE	4	/* Abort Cause */
-#define U8500_I2C_SR_SHIFT_TYPE	7	/* Receive Type */
-#define U8500_I2C_SR_SHIFT_LENGTH	9	/* Transfer length */
-
-/* abort cause */
-#define	U8500_I2C_NACK_ADDR	0
-#define	U8500_I2C_NACK_DATA	1
-#define	U8500_I2C_ACK_MCODE	2
-#define	U8500_I2C_ARB_LOST	3
-#define	U8500_I2C_BERR_START	4
-#define	U8500_I2C_BERR_STOP	5
-#define	U8500_I2C_OVFL	6
-
-
-/* Baud rate counter registers */
-
-/* Mask values for Baud rate counter register */
-#define U8500_I2C_BRCR_BRCNT2	0xFFFF		/* Baud Rate Cntr BRCR for HS */
-#define U8500_I2C_BRCR_BRCNT1	0xFFFF0000	/* BRCR for Standard and Fast */
-
-/* Shift values for the Baud rate counter register */
-#define U8500_I2C_BRCR_SHIFT_BRCNT2	0
-#define U8500_I2C_BRCR_SHIFT_BRCNT1	16
-
-
-/* Interrupt Register  */
-
-/* Mask values for Interrupt registers */
-#define U8500_I2C_INT_TXFE	0x00000001	/* Tx fifo empty */
-#define U8500_I2C_INT_TXFNE	0x00000002	/* Tx Fifo nearly empty */
-#define U8500_I2C_INT_TXFF	0x00000004	/* Tx Fifo Full */
-#define U8500_I2C_INT_TXFOVR	0x00000008	/* Tx Fifo over run */
-#define U8500_I2C_INT_RXFE	0x00000010	/* Rx Fifo Empty */
-#define U8500_I2C_INT_RXFNF	0x00000020	/* Rx Fifo nearly empty */
-#define U8500_I2C_INT_RXFF	0x00000040	/* Rx Fifo Full  */
-#define U8500_I2C_INT_RFSR	0x00010000	/* Read From slave request */
-#define U8500_I2C_INT_RFSE	0x00020000	/* Read from slave empty */
-#define U8500_I2C_INT_WTSR	0x00040000	/* Write to Slave request */
-#define U8500_I2C_INT_MTD	0x00080000	/* Master Transcation Done*/
-#define U8500_I2C_INT_STD	0x00100000	/* Slave Transaction Done */
-#define U8500_I2C_INT_MAL	0x01000000	/* Master Arbitation Lost */
-#define U8500_I2C_INT_BERR	0x02000000	/* Bus Error */
-#define U8500_I2C_INT_MTDWS	0x10000000	/* Master Tran Done wo/ Stop */
-
-/* Max clocks (Hz) */
-#define U8500_I2C_MAX_STANDARD_SCL	100000
-#define U8500_I2C_MAX_FAST_SCL		400000
-#define U8500_I2C_MAX_HIGH_SPEED_SCL	3400000
-
-#endif	/* _U8500_I2C_H_ */