ppc: Remove MPC8315ERDB board

This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM.  Remove it.  As this is the last
ARCH_MPC8315 platform, remove that support as well.

Signed-off-by: Tom Rini <trini@konsulko.com>

1 files changed, 0 insertions, 370 deletions

diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h
deleted file mode 100644
index 688aa5ea986..00000000000
--- a/include/configs/MPC8315ERDB.h
+++ /dev/null
@@ -1,370 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2007-2010 Freescale Semiconductor, Inc.
- *
- * Dave Liu <daveliu@freescale.com>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
-#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
-#define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
-#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
-
-#ifndef CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-#endif
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300		1 /* E300 family */
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRH		0x00000000
-#define CONFIG_SYS_SICRL		0x00000000 /* 3.3V, no delay */
-
-#define CONFIG_HWCONFIG
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory */
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
-#define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN \
-				| DDRCDR_PZ_LOZ \
-				| DDRCDR_NZ_LOZ \
-				| DDRCDR_ODT \
-				| DDRCDR_Q_DRN)
-				/* 0x7b880001 */
-/*
- * Manually set up DDR parameters
- * consist of two chips HY5PS12621BFP-C4 from HYNIX
- */
-#define CONFIG_SYS_DDR_SIZE		128 /* MB */
-#define CONFIG_SYS_DDR_CS0_BNDS	0x00000007
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
-				| CSCONFIG_ODT_RD_NEVER \
-				| CSCONFIG_ODT_WR_ONLY_CURRENT \
-				| CSCONFIG_ROW_BIT_13 \
-				| CSCONFIG_COL_BIT_10)
-				/* 0x80010102 */
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-#define CONFIG_SYS_DDR_TIMING_0	((0 << TIMING_CFG0_RWT_SHIFT) \
-				| (0 << TIMING_CFG0_WRT_SHIFT) \
-				| (0 << TIMING_CFG0_RRT_SHIFT) \
-				| (0 << TIMING_CFG0_WWT_SHIFT) \
-				| (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
-				| (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
-				| (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
-				| (2 << TIMING_CFG0_MRS_CYC_SHIFT))
-				/* 0x00220802 */
-#define CONFIG_SYS_DDR_TIMING_1	((2 << TIMING_CFG1_PRETOACT_SHIFT) \
-				| (7 << TIMING_CFG1_ACTTOPRE_SHIFT) \
-				| (2 << TIMING_CFG1_ACTTORW_SHIFT) \
-				| (5 << TIMING_CFG1_CASLAT_SHIFT) \
-				| (6 << TIMING_CFG1_REFREC_SHIFT) \
-				| (2 << TIMING_CFG1_WRREC_SHIFT) \
-				| (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
-				| (2 << TIMING_CFG1_WRTORD_SHIFT))
-				/* 0x27256222 */
-#define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) \
-				| (4 << TIMING_CFG2_CPO_SHIFT) \
-				| (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
-				| (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
-				| (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
-				| (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
-				| (5 << TIMING_CFG2_FOUR_ACT_SHIFT))
-				/* 0x121048c5 */
-#define CONFIG_SYS_DDR_INTERVAL	((0x0360 << SDRAM_INTERVAL_REFINT_SHIFT) \
-				| (0x0100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
-				/* 0x03600100 */
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SREN \
-				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
-				| SDRAM_CFG_DBW_32)
-				/* 0x43080000 */
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000 /* 1 posted refresh */
-#define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) \
-				| (0x0232 << SDRAM_MODE_SD_SHIFT))
-				/* ODT 150ohm CL=3, AL=1 on SDRAM */
-#define CONFIG_SYS_DDR_MODE2	0x00000000
-
-/*
- * Memory test
- */
-#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
-
-/*
- * The reserved memory
- */
-#define CONFIG_SYS_MONITOR_LEN	(512 * 1024) /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN	(512 * 1024) /* Reserved for malloc */
-
-/*
- * Initial RAM Base Address Setup
- */
-#define CONFIG_SYS_INIT_RAM_LOCK	1
-#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000 /* Size of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET	\
-			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*
- * FLASH on the Local Bus
- */
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
-
-#define CONFIG_SYS_FLASH_BASE		0xFE000000 /* FLASH base address */
-#define CONFIG_SYS_FLASH_SIZE		8	/* FLASH size is 8M */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	1 /* number of banks */
-/* 127 64KB sectors and 8 8KB top sectors per device */
-#define CONFIG_SYS_MAX_FLASH_SECT	135
-
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500 /* Flash Write Timeout (ms) */
-
-/*
- * NAND Flash on the Local Bus
- */
-
-#ifdef CONFIG_NAND_SPL
-#define CONFIG_SYS_NAND_BASE		0xFFF00000
-#else
-#define CONFIG_SYS_NAND_BASE		0xE0600000
-#endif
-
-#define CONFIG_MTD_PARTITION
-
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_NAND_FSL_ELBC		1
-#define CONFIG_SYS_NAND_BLOCK_SIZE	16384
-#define CONFIG_SYS_NAND_WINDOW_SIZE    (32 * 1024)     /* 0x00008000 */
-
-#define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
-#define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
-#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
-#define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
-#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
-
-
-
-/* Still needed for spl_minimal.c */
-#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM
-#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM
-
-#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE && \
-	!defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef CONFIG_SYS_RAMBOOT
-#endif
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0))
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x51} }
-
-/*
- * Board info - revision and where boot from
- */
-#define CONFIG_SYS_I2C_PCF8574A_ADDR	0x39
-
-/*
- * Config on-board RTC
- */
-#define CONFIG_RTC_DS1337	/* ds1339 on board, use ds1337 rtc via i2c */
-#define CONFIG_SYS_I2C_RTC_ADDR	0x68 /* at address 0x68 */
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI_MEM_BASE		0x80000000
-#define CONFIG_SYS_PCI_MEM_PHYS		CONFIG_SYS_PCI_MEM_BASE
-#define CONFIG_SYS_PCI_MEM_SIZE		0x10000000 /* 256M */
-#define CONFIG_SYS_PCI_MMIO_BASE	0x90000000
-#define CONFIG_SYS_PCI_MMIO_PHYS	CONFIG_SYS_PCI_MMIO_BASE
-#define CONFIG_SYS_PCI_MMIO_SIZE	0x10000000 /* 256M */
-#define CONFIG_SYS_PCI_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI_IO_PHYS		0xE0300000
-#define CONFIG_SYS_PCI_IO_SIZE		0x100000 /* 1M */
-
-#define CONFIG_SYS_PCI_SLV_MEM_LOCAL	CONFIG_SYS_SDRAM_BASE
-#define CONFIG_SYS_PCI_SLV_MEM_BUS	0x00000000
-#define CONFIG_SYS_PCI_SLV_MEM_SIZE	0x80000000
-
-#define CONFIG_SYS_PCIE1_BASE		0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_BASE	0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xA0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000
-#define CONFIG_SYS_PCIE1_CFG_BASE	0xB0000000
-#define CONFIG_SYS_PCIE1_CFG_SIZE	0x01000000
-#define CONFIG_SYS_PCIE1_IO_BASE	0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xB1000000
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00800000
-
-#define CONFIG_SYS_PCIE2_BASE		0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_BASE	0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xC0000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000
-#define CONFIG_SYS_PCIE2_CFG_BASE	0xD0000000
-#define CONFIG_SYS_PCIE2_CFG_SIZE	0x01000000
-#define CONFIG_SYS_PCIE2_IO_BASE	0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xD1000000
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00800000
-
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_PCIE
-
-#undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957	/* Freescale */
-
-#define CONFIG_HAS_FSL_DR_USB
-#define CONFIG_SYS_SCCR_USBDRCM		3
-
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_USB_PHY_TYPE	"utmi"
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-
-/*
- * TSEC
- */
-#define CONFIG_SYS_TSEC1_OFFSET	0x24000
-#define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
-#define CONFIG_SYS_TSEC2_OFFSET	0x25000
-#define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
-
-/*
- * TSEC ethernet configuration
- */
-#define CONFIG_TSEC1		1
-#define CONFIG_TSEC1_NAME	"eTSEC0"
-#define CONFIG_TSEC2		1
-#define CONFIG_TSEC2_NAME	"eTSEC1"
-#define TSEC1_PHY_ADDR		0
-#define TSEC2_PHY_ADDR		1
-#define TSEC1_PHYIDX		0
-#define TSEC2_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#define TSEC2_FLAGS		TSEC_GIGABIT
-
-/* Options are: eTSEC[0-1] */
-#define CONFIG_ETHPRIME		"eTSEC1"
-
-/*
- * SATA
- */
-#define CONFIG_SYS_SATA_MAX_DEVICE	2
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1_OFFSET	0x18000
-#define CONFIG_SYS_SATA1	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA1_OFFSET)
-#define CONFIG_SYS_SATA1_FLAGS	FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2_OFFSET	0x19000
-#define CONFIG_SYS_SATA2	(CONFIG_SYS_IMMR + CONFIG_SYS_SATA2_OFFSET)
-#define CONFIG_SYS_SATA2_FLAGS	FLAGS_DMA
-
-#ifdef CONFIG_FSL_SATA
-#define CONFIG_LBA48
-#endif
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#undef CONFIG_WATCHDOG		/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR		0x2000000 /* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(256 << 20) /* Initial Memory map for Linux */
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-/*
- * MMU Setup
- */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-#define CONFIG_LOADADDR 800000	/* default location for tftp and bootm */
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"consoledev=ttyS0\0"						\
-	"ramdiskaddr=1000000\0"						\
-	"ramdiskfile=ramfs.83xx\0"					\
-	"fdtaddr=780000\0"						\
-	"fdtfile=mpc8315erdb.dtb\0"					\
-	"usb_phy_type=utmi\0"						\
-	""
-
-#define CONFIG_NFSBOOTCOMMAND						\
-	"setenv bootargs root=/dev/nfs rw "				\
-		"nfsroot=$serverip:$rootpath "				\
-		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
-							"$netdev:off "	\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND						\
-	"setenv bootargs root=/dev/ram rw "				\
-		"console=$consoledev,$baudrate $othbootargs;"		\
-	"tftp $ramdiskaddr $ramdiskfile;"				\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
-#endif	/* __CONFIG_H */