OMAP3: Add SPL support to Beagleboard

This introduces 200MHz Micron parts timing information based on x-loader
to <asm/arch-omap3/mem.h> and Numonyx MCFG calculation.  The memory init
logic is also based on what x-loader does in these cases.  Note that
while previously u-boot would be flashed in with SW ECC in this case it
now must be flashed with HW ECC.  We also change CONFIG_SYS_TEXT_BASE to
0x80100000.

Cc: Dirk Behme <dirk.behme@gmail.com>
Beagleboard rev C5, xM rev A:
Tested-by: Tom Rini <trini@ti.com>
Beagleboard xM rev C:
Tested-by: Matt Ranostay <mranostay@gmail.com>
Beagleboard rev B7, C2, xM rev B:
Tested-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>

1 files changed, 55 insertions, 4 deletions

diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index a33aa419776..91af8a02569 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -110,9 +110,6 @@
 #define STATUS_LED_BOOT			STATUS_LED_BIT
 #define STATUS_LED_GREEN		STATUS_LED_BIT1
 
-/* DDR - I use Micron DDR */
-#define CONFIG_OMAP3_MICRON_DDR		1
-
 /* Enable Multi Bus support for I2C */
 #define CONFIG_I2C_MULTI_BUS		1
 
@@ -342,7 +339,6 @@
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE	(32 << 20)	/* at least 32 MiB */
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1
 
 /*-----------------------------------------------------------------------
@@ -384,4 +380,59 @@
 
 #define CONFIG_SYS_CACHELINE_SIZE	64
 
+/* Defines for SPL */
+#define CONFIG_SPL
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_TEXT_BASE		0x40200800
+#define CONFIG_SPL_MAX_SIZE		(45 * 1024)
+#define CONFIG_SPL_STACK		LOW_LEVEL_SRAM_STACK
+
+#define CONFIG_SPL_BSS_START_ADDR	0x80000000
+#define CONFIG_SPL_BSS_MAX_SIZE		0x80000		/* 512 KB */
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x200 /* 256 KB */
+#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION	1
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME	"u-boot.img"
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_OMAP3_ID_NAND
+#define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/omap-common/u-boot-spl.lds"
+
+/* NAND boot config */
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_PAGE_COUNT	64
+#define CONFIG_SYS_NAND_PAGE_SIZE	2048
+#define CONFIG_SYS_NAND_OOBSIZE		64
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128*1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS	0
+#define CONFIG_SYS_NAND_ECCPOS		{2, 3, 4, 5, 6, 7, 8, 9,\
+						10, 11, 12, 13}
+#define CONFIG_SYS_NAND_ECCSIZE		512
+#define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_SYS_NAND_ECCSTEPS	(CONFIG_SYS_NAND_PAGE_SIZE / \
+						CONFIG_SYS_NAND_ECCSIZE)
+#define CONFIG_SYS_NAND_ECCTOTAL	(CONFIG_SYS_NAND_ECCBYTES * \
+						CONFIG_SYS_NAND_ECCSTEPS)
+#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
+
+/*
+ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
+ * 64 bytes before this address should be set aside for u-boot.img's
+ * header. That is 0x800FFFC0--0x80100000 should not be used for any
+ * other needs.
+ */
+#define CONFIG_SYS_TEXT_BASE		0x80100000
+#define CONFIG_SYS_SPL_MALLOC_START	0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000
+
 #endif /* __CONFIG_H */