ppc: Zap TQM8260 board

This board is old and is using CONFIG_I2C_X, which is wrong.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>

1 files changed, 0 insertions, 620 deletions

diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h
deleted file mode 100644
index 7fd12d3fbc6..00000000000
--- a/include/configs/TQM8260.h
+++ /dev/null
@@ -1,620 +0,0 @@
-/*
- * (C) Copyright 2001-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * Imported from global configuration:
- *	CONFIG_MPC8255
- *	CONFIG_MPC8265
- *	CONFIG_200MHz
- *	CONFIG_266MHz
- *	CONFIG_300MHz
- *	CONFIG_L2_CACHE
- *	CONFIG_BUSMODE_60x
- */
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define	CONFIG_SYS_TEXT_BASE	0x40000000
-
-
-#if 0
-#define CONFIG_TQM8260		100	/* ...on a TQM8260 module Rev.100	*/
-#else
-#define CONFIG_TQM8260		200	/* ...on a TQM8260 module Rev.200	*/
-#endif
-
-#define CONFIG_CPM2		1	/* Has a CPM2 */
-
-#define CONFIG_82xx_CONS_SMC1	1	/* console on SMC1			*/
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define	CONFIG_BOOTCOUNT_LIMIT
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"rootpath=/opt/eldk/ppc_6xx\0"					\
-	"bootfile=tqm8260/uImage\0"				\
-	"kernel_addr=400C0000\0"					\
-	"ramdisk_addr=40240000\0"					\
-	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-/* enable I2C and select the hardware/software driver */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_SOFT		/* I2C bit-banged */
-#define CONFIG_SYS_I2C_SOFT_SPEED	400000
-#define CONFIG_SYS_I2C_SOFT_SLAVE	0x7F
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-
-/* TQM8260 Rev.100 has the clock and data pins swapped (!!!) on EEPROM */
-#if (CONFIG_TQM8260 <= 100)
-
-#define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE	(iop->pdir |=  0x00020000)
-#define I2C_TRISTATE	(iop->pdir &= ~0x00020000)
-#define I2C_READ	((iop->pdat & 0x00020000) != 0)
-#define I2C_SDA(bit)	if(bit) iop->pdat |=  0x00020000; \
-			else    iop->pdat &= ~0x00020000
-#define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00010000; \
-			else    iop->pdat &= ~0x00010000
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-
-#else
-
-#define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
-#define I2C_ACTIVE	(iop->pdir |=  0x00010000)
-#define I2C_TRISTATE	(iop->pdir &= ~0x00010000)
-#define I2C_READ	((iop->pdat & 0x00010000) != 0)
-#define I2C_SDA(bit)	if(bit) iop->pdat |=  0x00010000; \
-			else    iop->pdat &= ~0x00010000
-#define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00020000; \
-			else    iop->pdat &= ~0x00020000
-#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
-#endif
-
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
-
-#define CONFIG_I2C_X
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere (for example, on the cogent platform, there are serial
- * ports on the motherboard which are used for the serial console - see
- * cogent/cma101/serial.[ch]).
- */
-#define CONFIG_CONS_ON_SMC		/* define if console on SMC */
-#undef  CONFIG_CONS_ON_SCC		/* define if console on SCC */
-#undef  CONFIG_CONS_NONE		/* define if console on something else*/
-#ifdef CONFIG_82xx_CONS_SMC1
-#define CONFIG_CONS_INDEX	1	/* which serial channel for console */
-#endif
-#ifdef CONFIG_82xx_CONS_SMC2
-#define CONFIG_CONS_INDEX	2	/* which serial channel for console */
-#endif
-
-#undef  CONFIG_CONS_USE_EXTC		/* SMC/SCC use ext clock not brg_clk */
-#define CONFIG_CONS_EXTC_RATE	3686400	/* SMC/SCC ext clk rate in Hz */
-#define CONFIG_CONS_EXTC_PINSEL	0	/* pin select 0=CLK3/CLK9 */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- *
- * (On TQM8260 either SCC1 or FCC2 may be chosen: SCC1 is hardwired to the
- * X.29 connector, and FCC2 is hardwired to the X.1 connector)
- */
-#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC       */
-#define	CONFIG_ETHER_ON_FCC		/* define if ether on FCC       */
-#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
-#define	CONFIG_ETHER_INDEX    2		/* which SCC/FCC channel for ethernet */
-
-#if defined(CONFIG_ETHER_ON_SCC) && (CONFIG_ETHER_INDEX == 1)
-
-/*
- *  - RX clk is CLK11
- *  - TX clk is CLK12
- */
-# define CONFIG_SYS_CMXSCR_VALUE1	(CMXSCR_RS1CS_CLK11 | CMXSCR_TS1CS_CLK12)
-
-#elif defined(CONFIG_ETHER_ON_FCC) && (CONFIG_ETHER_INDEX == 2)
-
-/*
- * - Rx-CLK is CLK13
- * - Tx-CLK is CLK14
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- * - Enable Full Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
-# define CONFIG_SYS_CPMFCR_RAMTYPE	0
-# define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
-
-#endif /* CONFIG_ETHER_ON_FCC, CONFIG_ETHER_INDEX */
-
-
-/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#if defined(CONFIG_MPC8255) || defined(CONFIG_MPC8265)
-#  define CONFIG_8260_CLKIN	66666666	/* in Hz */
-#else	/* !CONFIG_MPC8255 && !CONFIG_MPC8265 */
-# ifndef CONFIG_300MHz
-#  define CONFIG_8260_CLKIN	66666666	/* in Hz */
-# else
-#  define CONFIG_8260_CLKIN	83333000	/* in Hz */
-# endif
-#endif	/* CONFIG_MPC8255 */
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-#define	CONFIG_TIMESTAMP		/* Print image info with timestamp */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END	0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address	*/
-
-#define	CONFIG_SYS_RESET_ADDRESS 0xFFFFFFFC	/* "bad" address		*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ        (8 << 20)       /* Initial Memory map for Linux */
-
-
-/* What should the base address of the main FLASH be and how big is
- * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/tqm8260/config.mk
- * The main FLASH is whichever is connected to *CS0.
- */
-#define CONFIG_SYS_FLASH0_BASE 0x40000000
-#define CONFIG_SYS_FLASH1_BASE 0x60000000
-#define CONFIG_SYS_FLASH0_SIZE 32
-#define CONFIG_SYS_FLASH1_SIZE 32
-
-/* Flash bank size (for preliminary settings)
- */
-#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */
-#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max num of sects on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
-
-/* use CFI flash driver */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER		1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_FLASH_EMPTY_INFO	1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x40000)
-#define CONFIG_ENV_SIZE		0x08000
-#define CONFIG_ENV_SECT_SIZE	0x40000
-#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE
-
-/*-----------------------------------------------------------------------
- * Hardware Information Block
- */
-#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
-#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
-#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- *
- * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
- * defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
- */
-#define	__HRCW__ALL__		(HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
-
-#if defined(CONFIG_MPC8255) || defined(CONFIG_MPC8265)
-#  define CONFIG_SYS_HRCW_MASTER	(__HRCW__ALL__ | HRCW_MODCK_H0111)
-#else	/* ! MPC8255 && !MPC8265 */
-# if defined(CONFIG_266MHz)
-#  define CONFIG_SYS_HRCW_MASTER	(__HRCW__ALL__ | HRCW_MODCK_H0111)
-# elif defined(CONFIG_300MHz)
-#  define CONFIG_SYS_HRCW_MASTER	(__HRCW__ALL__ | HRCW_MODCK_H0110)
-# else
-#  define CONFIG_SYS_HRCW_MASTER	(__HRCW__ALL__)
-# endif
-#endif	/* CONFIG_MPC8255 */
-
-/* no slaves so just fill with zeros */
-#define CONFIG_SYS_HRCW_SLAVE1		0
-#define CONFIG_SYS_HRCW_SLAVE2		0
-#define CONFIG_SYS_HRCW_SLAVE3		0
-#define CONFIG_SYS_HRCW_SLAVE4		0
-#define CONFIG_SYS_HRCW_SLAVE5		0
-#define CONFIG_SYS_HRCW_SLAVE6		0
-#define CONFIG_SYS_HRCW_SLAVE7		0
-
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFFF00000
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE	0x4000  /* Size of used area in DPRAM    */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- *
- * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE, local SDRAM
- * is mapped at SDRAM_BASE2_PRELIM.
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()*/
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE      32      /* For MPC8260 CPU              */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers                    2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT   (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
-				HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID0_FINAL  (HID0_IFEM|HID0_ABE)
-#define CONFIG_SYS_HID2        0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register                                     5-5
- *-----------------------------------------------------------------------
- * turn on Checkstop Reset Enable
- */
-#define CONFIG_SYS_RMR         RMR_CSRE
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration                                       4-25
- *-----------------------------------------------------------------------
- */
-#ifdef	CONFIG_BUSMODE_60x
-#define CONFIG_SYS_BCR         (BCR_EBM|BCR_L2C|BCR_LETM|\
-			 BCR_NPQM0|BCR_NPQM1|BCR_NPQM2)	/* 60x mode  */
-#else
-#define BCR_APD01	0x10000000
-#define CONFIG_SYS_BCR		(BCR_APD01|BCR_ETM|BCR_LETM)	/* 8260 mode */
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration                             4-31
- *-----------------------------------------------------------------------
- */
-#if 0
-#define CONFIG_SYS_SIUMCR      (SIUMCR_DPPC10|SIUMCR_APPC10)
-#else
-#define CONFIG_SYS_SIUMCR      (SIUMCR_DPPC00|SIUMCR_APPC10)
-#endif
-
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control                             4-35
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
-			 SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
-#else
-#define CONFIG_SYS_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
-			 SYPCR_SWRI|SYPCR_SWP)
-#endif /* CONFIG_WATCHDOG */
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control                     4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC     (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control                 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR       (PISCR_PS|PISCR_PTF|PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control                                   9-8
- *-----------------------------------------------------------------------
- * Ensure DFBRG is Divide by 16
- */
-#define CONFIG_SYS_SCCR        0
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration                         13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR        0
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus     Machine PortSz  Device
- * ---- ---     ------- ------  ------
- *  0   60x     GPCM    64 bit  FLASH
- *  1   60x     SDRAM   64 bit  SDRAM
- *  2   Local   SDRAM   32 bit  SDRAM
- *
- */
-
-	/* Initialize SDRAM on local bus
-	 */
-#define CONFIG_SYS_INIT_LOCAL_SDRAM
-
-#define SDRAM_MAX_SIZE	0x08000000	/* max. 128 MB		*/
-
-/* Minimum mask to separate preliminary
- * address ranges for CS[0:2]
- */
-#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT	(512<<20)	/* less than 512 MB */
-#define CONFIG_SYS_LOCAL_SDRAM_LIMIT	(128<<20)	/* less than 128 MB */
-
-#define CONFIG_SYS_MPTPR       0x4000
-
-/*-----------------------------------------------------------------------------
- * Address for Mode Register Set (MRS) command
- *-----------------------------------------------------------------------------
- * In fact, the address is rather configuration data presented to the SDRAM on
- * its address lines. Because the address lines may be mux'ed externally either
- * for 8 column or 9 column devices, some bits appear twice in the 8260's
- * address:
- *
- * |   (RFU)   |   (RFU)   | WBL |    TM    |     CL    |  BT | Burst Length |
- * | BA1   BA0 | A12 : A10 |  A9 |  A8   A7 |  A6 : A4  |  A3 |   A2 :  A0   |
- *  8 columns mux'ing:     |  A9 | A10  A21 | A22 : A24 | A25 |  A26 : A28   |
- *  9 columns mux'ing:     |  A8 | A20  A21 | A22 : A24 | A25 |  A26 : A28   |
- *  Settings:              |  0  |  0    0  |  0  1  0  |  0  |   0  1  0    |
- *-----------------------------------------------------------------------------
- */
-#define CONFIG_SYS_MRS_OFFS	0x00000110
-
-
-/* Bank 0 - FLASH
- */
-#define CONFIG_SYS_BR0_PRELIM  ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK)  |\
-			 BRx_PS_64                      |\
-			 BRx_MS_GPCM_P                  |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM  (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE)      |\
-			 ORxG_CSNT                      |\
-			 ORxG_ACS_DIV1                  |\
-			 ORxG_SCY_3_CLK                 |\
-			 ORxG_EHTR                      |\
-			 ORxG_TRLX)
-
-	/* SDRAM on TQM8260 can have either 8 or 9 columns.
-	 * The number affects configuration values.
-	 */
-
-/* Bank 1 - 60x bus SDRAM
- */
-#define CONFIG_SYS_PSRT        0x20
-#define CONFIG_SYS_LSRT        0x20
-#ifndef CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_BR1_PRELIM  ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK)  |\
-			 BRx_PS_64                      |\
-			 BRx_MS_SDRAM_P                 |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR1_8COL
-
-
-	/* SDRAM initialization values for 8-column chips
-	 */
-#define CONFIG_SYS_OR1_8COL    ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
-			 ORxS_BPD_4                     |\
-			 ORxS_ROWST_PBI1_A7             |\
-			 ORxS_NUMR_12)
-
-#define CONFIG_SYS_PSDMR_8COL  (PSDMR_PBI                      |\
-			 PSDMR_SDAM_A15_IS_A5           |\
-			 PSDMR_BSMA_A12_A14             |\
-			 PSDMR_SDA10_PBI1_A8            |\
-			 PSDMR_RFRC_7_CLK               |\
-			 PSDMR_PRETOACT_2W              |\
-			 PSDMR_ACTTORW_2W               |\
-			 PSDMR_LDOTOPRE_1C              |\
-			 PSDMR_WRC_2C                   |\
-			 PSDMR_EAMUX                    |\
-			 PSDMR_CL_2)
-
-	/* SDRAM initialization values for 9-column chips
-	 */
-#define CONFIG_SYS_OR1_9COL    ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
-			 ORxS_BPD_4                     |\
-			 ORxS_ROWST_PBI1_A5             |\
-			 ORxS_NUMR_13)
-
-#define CONFIG_SYS_PSDMR_9COL  (PSDMR_PBI                      |\
-			 PSDMR_SDAM_A16_IS_A5           |\
-			 PSDMR_BSMA_A12_A14             |\
-			 PSDMR_SDA10_PBI1_A7            |\
-			 PSDMR_RFRC_7_CLK               |\
-			 PSDMR_PRETOACT_2W              |\
-			 PSDMR_ACTTORW_2W               |\
-			 PSDMR_LDOTOPRE_1C              |\
-			 PSDMR_WRC_2C                   |\
-			 PSDMR_EAMUX                    |\
-			 PSDMR_CL_2)
-
-/* Bank 2 - Local bus SDRAM
- */
-#ifdef CONFIG_SYS_INIT_LOCAL_SDRAM
-#define CONFIG_SYS_BR2_PRELIM  ((SDRAM_BASE2_PRELIM & BRx_BA_MSK) |\
-			 BRx_PS_32                      |\
-			 BRx_MS_SDRAM_L                 |\
-			 BRx_V)
-
-#define CONFIG_SYS_OR2_PRELIM	CONFIG_SYS_OR2_8COL
-
-#define SDRAM_BASE2_PRELIM	0x80000000
-
-	/* SDRAM initialization values for 8-column chips
-	 */
-#define CONFIG_SYS_OR2_8COL    ((~(CONFIG_SYS_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
-			 ORxS_BPD_4                     |\
-			 ORxS_ROWST_PBI1_A8             |\
-			 ORxS_NUMR_12)
-
-#define CONFIG_SYS_LSDMR_8COL  (PSDMR_PBI                      |\
-			 PSDMR_SDAM_A15_IS_A5           |\
-			 PSDMR_BSMA_A13_A15             |\
-			 PSDMR_SDA10_PBI1_A9            |\
-			 PSDMR_RFRC_7_CLK               |\
-			 PSDMR_PRETOACT_2W              |\
-			 PSDMR_ACTTORW_2W               |\
-			 PSDMR_BL                       |\
-			 PSDMR_LDOTOPRE_1C              |\
-			 PSDMR_WRC_2C                   |\
-			 PSDMR_CL_2)
-
-	/* SDRAM initialization values for 9-column chips
-	 */
-#define CONFIG_SYS_OR2_9COL    ((~(CONFIG_SYS_LOCAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
-			 ORxS_BPD_4                     |\
-			 ORxS_ROWST_PBI1_A6             |\
-			 ORxS_NUMR_13)
-
-#define CONFIG_SYS_LSDMR_9COL  (PSDMR_PBI                      |\
-			 PSDMR_SDAM_A16_IS_A5           |\
-			 PSDMR_BSMA_A13_A15             |\
-			 PSDMR_SDA10_PBI1_A8            |\
-			 PSDMR_RFRC_7_CLK               |\
-			 PSDMR_PRETOACT_2W              |\
-			 PSDMR_ACTTORW_2W               |\
-			 PSDMR_BL                       |\
-			 PSDMR_LDOTOPRE_1C              |\
-			 PSDMR_WRC_2C                   |\
-			 PSDMR_CL_2)
-
-#endif /* CONFIG_SYS_INIT_LOCAL_SDRAM */
-
-#endif /* CONFIG_SYS_RAMBOOT */
-
-#endif	/* __CONFIG_H */