nand: Sync with Linux v4.1

Update the NAND code to match Linux v4.1.  The previous sync was
from Linux v3.15 in commit 4e67c57125290b25.

CONFIG_SYS_NAND_RESET_CNT is removed, as the upstream Linux code now
has its own timeout.  Plus, CONFIG_SYS_NAND_RESET_CNT was undocumented
and not selected by any board.

Signed-off-by: Scott Wood <scottwood@freescale.com>

1 files changed, 82 insertions, 5 deletions

diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
index 7c07087394d..77b50ddcde2 100644
--- a/include/linux/mtd/nand.h
+++ b/include/linux/mtd/nand.h
@@ -472,8 +472,21 @@ struct nand_hw_control {
  *		be provided if an hardware ECC is available
  * @calculate:	function for ECC calculation or readback from ECC hardware
  * @correct:	function for ECC correction, matching to ECC generator (sw/hw)
- * @read_page_raw:	function to read a raw page without ECC
- * @write_page_raw:	function to write a raw page without ECC
+ * @read_page_raw:	function to read a raw page without ECC. This function
+ *			should hide the specific layout used by the ECC
+ *			controller and always return contiguous in-band and
+ *			out-of-band data even if they're not stored
+ *			contiguously on the NAND chip (e.g.
+ *			NAND_ECC_HW_SYNDROME interleaves in-band and
+ *			out-of-band data).
+ * @write_page_raw:	function to write a raw page without ECC. This function
+ *			should hide the specific layout used by the ECC
+ *			controller and consider the passed data as contiguous
+ *			in-band and out-of-band data. ECC controller is
+ *			responsible for doing the appropriate transformations
+ *			to adapt to its specific layout (e.g.
+ *			NAND_ECC_HW_SYNDROME interleaves in-band and
+ *			out-of-band data).
  * @read_page:	function to read a page according to the ECC generator
  *		requirements; returns maximum number of bitflips corrected in
  *		any single ECC step, 0 if bitflips uncorrectable, -EIO hw error
@@ -575,8 +588,7 @@ struct nand_buffers {
  * @ecc:		[BOARDSPECIFIC] ECC control structure
  * @buffers:		buffer structure for read/write
  * @hwcontrol:		platform-specific hardware control structure
- * @erase_cmd:		[INTERN] erase command write function, selectable due
- *			to AND support.
+ * @erase:		[REPLACEABLE] erase function
  * @scan_bbt:		[REPLACEABLE] function to scan bad block table
  * @chip_delay:		[BOARDSPECIFIC] chip dependent delay for transferring
  *			data from array to read regs (tR).
@@ -606,6 +618,11 @@ struct nand_buffers {
  * @ecc_step_ds:	[INTERN] ECC step required by the @ecc_strength_ds,
  *                      also from the datasheet. It is the recommended ECC step
  *			size, if known; if unknown, set to zero.
+ * @onfi_timing_mode_default: [INTERN] default ONFI timing mode. This field is
+ *			      either deduced from the datasheet if the NAND
+ *			      chip is not ONFI compliant or set to 0 if it is
+ *			      (an ONFI chip is always configured in mode 0
+ *			      after a NAND reset)
  * @numchips:		[INTERN] number of physical chips
  * @chipsize:		[INTERN] the size of one chip for multichip arrays
  * @pagemask:		[INTERN] page number mask = number of (pages / chip) - 1
@@ -660,7 +677,7 @@ struct nand_chip {
 	void (*cmdfunc)(struct mtd_info *mtd, unsigned command, int column,
 			int page_addr);
 	int(*waitfunc)(struct mtd_info *mtd, struct nand_chip *this);
-	void (*erase_cmd)(struct mtd_info *mtd, int page);
+	int (*erase)(struct mtd_info *mtd, int page);
 	int (*scan_bbt)(struct mtd_info *mtd);
 	int (*errstat)(struct mtd_info *mtd, struct nand_chip *this, int state,
 			int status, int page);
@@ -690,6 +707,7 @@ struct nand_chip {
 	uint8_t bits_per_cell;
 	uint16_t ecc_strength_ds;
 	uint16_t ecc_step_ds;
+	int onfi_timing_mode_default;
 	int badblockpos;
 	int badblockbits;
 
@@ -737,6 +755,7 @@ struct nand_chip {
 #define NAND_MFR_EON		0x92
 #define NAND_MFR_SANDISK	0x45
 #define NAND_MFR_INTEL		0x89
+#define NAND_MFR_ATO		0x9b
 
 /* The maximum expected count of bytes in the NAND ID sequence */
 #define NAND_MAX_ID_LEN 8
@@ -786,12 +805,17 @@ struct nand_chip {
  * @options: stores various chip bit options
  * @id_len: The valid length of the @id.
  * @oobsize: OOB size
+ * @ecc: ECC correctability and step information from the datasheet.
  * @ecc.strength_ds: The ECC correctability from the datasheet, same as the
  *                   @ecc_strength_ds in nand_chip{}.
  * @ecc.step_ds: The ECC step required by the @ecc.strength_ds, same as the
  *               @ecc_step_ds in nand_chip{}, also from the datasheet.
  *               For example, the "4bit ECC for each 512Byte" can be set with
  *               NAND_ECC_INFO(4, 512).
+ * @onfi_timing_mode_default: the default ONFI timing mode entered after a NAND
+ *			      reset. Should be deduced from timings described
+ *			      in the datasheet.
+ *
  */
 struct nand_flash_dev {
 	char *name;
@@ -812,6 +836,7 @@ struct nand_flash_dev {
 		uint16_t strength_ds;
 		uint16_t step_ds;
 	} ecc;
+	int onfi_timing_mode_default;
 };
 
 /**
@@ -983,4 +1008,56 @@ void nand_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len);
 void nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len);
 void nand_read_buf16(struct mtd_info *mtd, uint8_t *buf, int len);
 uint8_t nand_read_byte(struct mtd_info *mtd);
+
+/*
+ * struct nand_sdr_timings - SDR NAND chip timings
+ *
+ * This struct defines the timing requirements of a SDR NAND chip.
+ * These informations can be found in every NAND datasheets and the timings
+ * meaning are described in the ONFI specifications:
+ * www.onfi.org/~/media/ONFI/specs/onfi_3_1_spec.pdf (chapter 4.15 Timing
+ * Parameters)
+ *
+ * All these timings are expressed in picoseconds.
+ */
+
+struct nand_sdr_timings {
+	u32 tALH_min;
+	u32 tADL_min;
+	u32 tALS_min;
+	u32 tAR_min;
+	u32 tCEA_max;
+	u32 tCEH_min;
+	u32 tCH_min;
+	u32 tCHZ_max;
+	u32 tCLH_min;
+	u32 tCLR_min;
+	u32 tCLS_min;
+	u32 tCOH_min;
+	u32 tCS_min;
+	u32 tDH_min;
+	u32 tDS_min;
+	u32 tFEAT_max;
+	u32 tIR_min;
+	u32 tITC_max;
+	u32 tRC_min;
+	u32 tREA_max;
+	u32 tREH_min;
+	u32 tRHOH_min;
+	u32 tRHW_min;
+	u32 tRHZ_max;
+	u32 tRLOH_min;
+	u32 tRP_min;
+	u32 tRR_min;
+	u64 tRST_max;
+	u32 tWB_max;
+	u32 tWC_min;
+	u32 tWH_min;
+	u32 tWHR_min;
+	u32 tWP_min;
+	u32 tWW_min;
+};
+
+/* get timing characteristics from ONFI timing mode. */
+const struct nand_sdr_timings *onfi_async_timing_mode_to_sdr_timings(int mode);
 #endif /* __LINUX_MTD_NAND_H */