ppc: Remove MPC8544DS board

This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI.  The
deadline for this conversion was the v2019.07 release.  The use of CONFIG_AHCI
requires CONFIG_DM.  The deadline for this conversion was v2020.01.  Remove
this board.

Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>

1 files changed, 0 insertions, 408 deletions

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
deleted file mode 100644
index f4f41da4988..00000000000
--- a/include/configs/MPC8544DS.h
+++ /dev/null
@@ -1,408 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc.
- */
-
-/*
- * mpc8544ds board configuration file
- *
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_PCI1		1	/* PCI controller 1 */
-#define CONFIG_PCIE1		1	/* PCIE controller 1 (slot 1) */
-#define CONFIG_PCIE2		1	/* PCIE controller 2 (slot 2) */
-#define CONFIG_PCIE3		1	/* PCIE controller 3 (ULI bridge) */
-#define CONFIG_FSL_PCI_INIT	1	/* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1	/* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT	1	/* enable 64-bit PCI resources */
-
-#define CONFIG_INTERRUPTS		/* enable pci, srio, ddr interrupts */
-
-#ifndef __ASSEMBLY__
-#include <linux/stringify.h>
-extern unsigned long get_board_sys_clk(unsigned long dummy);
-#endif
-#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk(0) /* sysclk for MPC85xx */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE			/* toggle L2 cache */
-#define CONFIG_BTB			/* toggle branch predition */
-
-/*
- * Only possible on E500 Version 2 or newer cores.
- */
-#define CONFIG_ENABLE_36BIT_PHYS	1
-
-#define CONFIG_SYS_CCSRBAR		0xe0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
-#define CONFIG_DDR_SPD
-
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER	/* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE	0xDeadBeef
-
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_VERY_BIG_RAM
-
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	2
-
-/* I2C addresses of SPD EEPROMs */
-#define SPD_EEPROM_ADDRESS	0x51		/* DDR DIMM */
-
-/* Make sure required options are set */
-#ifndef CONFIG_SPD_EEPROM
-#error ("CONFIG_SPD_EEPROM is required")
-#endif
-
-/*
- * Memory map
- *
- * 0x0000_0000	0x7fff_ffff	DDR			2G Cacheable
- *
- * 0x8000_0000	0xbfff_ffff	PCI Express Mem		1G non-cacheable
- *
- * 0xc000_0000	0xdfff_ffff	PCI			512M non-cacheable
- *
- * 0xe000_0000	0xe00f_ffff	CCSR			1M non-cacheable
- * 0xe100_0000	0xe3ff_ffff	PCI IO range		4M non-cacheable
- *
- * Localbus cacheable
- *
- * 0xf000_0000	0xf3ff_ffff	SDRAM			64M Cacheable
- * 0xf401_0000	0xf401_3fff	L1 for stack		4K Cacheable TLB0
- *
- * Localbus non-cacheable
- *
- * 0xf800_0000	0xf80f_ffff	NVRAM/CADMUS (*)	1M non-cacheable
- * 0xff00_0000	0xff7f_ffff	FLASH (2nd bank)	8M non-cacheable
- * 0xff80_0000	0xffff_ffff	FLASH (boot bank)	8M non-cacheable
- *
- */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_BOOT_BLOCK		0xfc000000	/* boot TLB */
-
-#define CONFIG_SYS_FLASH_BASE		0xff800000	/* start of FLASH 8M */
-
-#define CONFIG_SYS_BR0_PRELIM		0xff801001
-#define CONFIG_SYS_BR1_PRELIM		0xfe801001
-
-#define CONFIG_SYS_OR0_PRELIM		0xff806e65
-#define CONFIG_SYS_OR1_PRELIM		0xff806e65
-
-#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE}
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	128		/* sectors per device */
-#undef	CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000		/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Flash Write Timeout (ms) */
-#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-
-#define CONFIG_SYS_LBC_NONCACHE_BASE	0xf8000000
-
-#define CONFIG_SYS_BR2_PRELIM		0xf8201001	/* port size 16bit */
-#define CONFIG_SYS_OR2_PRELIM		0xfff06ff7	/* 1MB Compact Flash area*/
-
-#define CONFIG_SYS_BR3_PRELIM		0xf8100801	/* port size 8bit */
-#define CONFIG_SYS_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/
-
-#define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
-#define PIXIS_BASE	0xf8100000	/* PIXIS registers */
-#define PIXIS_ID		0x0	/* Board ID at offset 0 */
-#define PIXIS_VER		0x1	/* Board version at offset 1 */
-#define PIXIS_PVER		0x2	/* PIXIS FPGA version at offset 2 */
-#define PIXIS_RST		0x4	/* PIXIS Reset Control register */
-#define PIXIS_AUX		0x6	/* PIXIS Auxiliary register; Scratch
-					 * register */
-#define PIXIS_SPD		0x7	/* Register for SYSCLK speed */
-#define PIXIS_VCTL		0x10	/* VELA Control Register */
-#define PIXIS_VCFGEN0		0x12	/* VELA Config Enable 0 */
-#define PIXIS_VCFGEN1		0x13	/* VELA Config Enable 1 */
-#define PIXIS_VBOOT		0x16	/* VELA VBOOT Register */
-#define PIXIS_VBOOT_FMAP	0x80	/* VBOOT - CFG_FLASHMAP */
-#define PIXIS_VBOOT_FBANK	0x40	/* VBOOT - CFG_FLASHBANK */
-#define PIXIS_VSPEED0		0x17	/* VELA VSpeed 0 */
-#define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
-#define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
-#define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
-#define PIXIS_VSPEED2		0x1d	/* VELA VSpeed 2 */
-#define CONFIG_SYS_PIXIS_VBOOT_MASK	0x40    /* Reset altbank mask*/
-#define PIXIS_VSPEED2_TSEC1SER	0x2
-#define PIXIS_VSPEED2_TSEC3SER	0x1
-#define PIXIS_VCFGEN1_TSEC1SER	0x20
-#define PIXIS_VCFGEN1_TSEC3SER	0x40
-#define PIXIS_VSPEED2_MASK	(PIXIS_VSPEED2_TSEC1SER|PIXIS_VSPEED2_TSEC3SER)
-#define PIXIS_VCFGEN1_MASK	(PIXIS_VCFGEN1_TSEC1SER|PIXIS_VCFGEN1_TSEC3SER)
-
-#define CONFIG_SYS_INIT_RAM_LOCK      1
-#define CONFIG_SYS_INIT_RAM_ADDR      0xf4010000      /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_SIZE       0x00004000      /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */
-
-/* Serial Port - controlled on board with jumper J8
- * open - index 2
- * shorted - index 1
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x4600)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3100
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-#define CONFIG_SYS_PCIE_VIRT		0x80000000	/* 1G PCIE TLB */
-#define CONFIG_SYS_PCIE_PHYS		0x80000000	/* 1G PCIE TLB */
-#define CONFIG_SYS_PCI_VIRT		0xc0000000	/* 512M PCI TLB */
-#define CONFIG_SYS_PCI_PHYS		0xc0000000	/* 512M PCI TLB */
-
-#define CONFIG_SYS_PCI1_MEM_VIRT	0xc0000000
-#define CONFIG_SYS_PCI1_MEM_BUS	0xc0000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	0xc0000000
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCI1_IO_VIRT	0xe1000000
-#define CONFIG_SYS_PCI1_IO_BUS	0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS	0xe1000000
-#define CONFIG_SYS_PCI1_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 2, Slot 1, tgtid 1, Base address 9000 */
-#define CONFIG_SYS_PCIE2_NAME		"Slot 1"
-#define CONFIG_SYS_PCIE2_MEM_VIRT	0x80000000
-#define CONFIG_SYS_PCIE2_MEM_BUS	0x80000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0x80000000
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x20000000	/* 512M */
-#define CONFIG_SYS_PCIE2_IO_VIRT	0xe1010000
-#define CONFIG_SYS_PCIE2_IO_BUS	0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xe1010000
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 1, Slot 2,tgtid 2, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME		"Slot 2"
-#define CONFIG_SYS_PCIE1_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xa0000000
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCIE1_IO_VIRT	0xe1020000
-#define CONFIG_SYS_PCIE1_IO_BUS	0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xe1020000
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 3, direct to uli, tgtid 3, Base address b000 */
-#define CONFIG_SYS_PCIE3_NAME		"ULI"
-#define CONFIG_SYS_PCIE3_MEM_VIRT	0xb0000000
-#define CONFIG_SYS_PCIE3_MEM_BUS	0xb0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	0xb0000000
-#define CONFIG_SYS_PCIE3_MEM_SIZE	0x00100000	/* 1M */
-#define CONFIG_SYS_PCIE3_IO_VIRT	0xb0100000	/* reuse mem LAW */
-#define CONFIG_SYS_PCIE3_IO_BUS	0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS	0xb0100000	/* reuse mem LAW */
-#define CONFIG_SYS_PCIE3_IO_SIZE	0x00100000	/* 1M */
-#define CONFIG_SYS_PCIE3_MEM_VIRT2	0xb0200000
-#define CONFIG_SYS_PCIE3_MEM_BUS2	0xb0200000
-#define CONFIG_SYS_PCIE3_MEM_PHYS2	0xb0200000
-#define CONFIG_SYS_PCIE3_MEM_SIZE2	0x00200000	/* 1M */
-
-#if defined(CONFIG_PCI)
-
-/*PCIE video card used*/
-#define VIDEO_IO_OFFSET		CONFIG_SYS_PCIE2_IO_VIRT
-
-/*PCI video card used*/
-/*#define VIDEO_IO_OFFSET	CONFIG_SYS_PCI1_IO_VIRT*/
-
-/* video */
-
-#if defined(CONFIG_VIDEO)
-#define CONFIG_BIOSEMU
-#define CONFIG_ATI_RADEON_FB
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
-#endif
-
-
-#ifndef CONFIG_PCI_PNP
-	#define PCI_ENET0_IOADDR	CONFIG_SYS_PCI1_IO_BUS
-	#define PCI_ENET0_MEMADDR	CONFIG_SYS_PCI1_IO_BUS
-	#define PCI_IDSEL_NUMBER	0x11	/* IDSEL = AD11 */
-#endif
-
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-
-#ifdef CONFIG_SCSI_AHCI
-#define CONFIG_SATA_ULI5288
-#define CONFIG_SYS_SCSI_MAX_SCSI_ID	4
-#define CONFIG_SYS_SCSI_MAX_LUN	1
-#define CONFIG_SYS_SCSI_MAX_DEVICE	(CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
-#endif /* CONFIG_SCSI_AHCI */
-
-#endif	/* CONFIG_PCI */
-
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII_DEFAULT_TSEC	1	/* Allow unregistered phys */
-#define CONFIG_TSEC1	1
-#define CONFIG_TSEC1_NAME	"eTSEC1"
-#define CONFIG_TSEC3	1
-#define CONFIG_TSEC3_NAME	"eTSEC3"
-
-#define CONFIG_PIXIS_SGMII_CMD
-#define CONFIG_FSL_SGMII_RISER	1
-#define SGMII_RISER_PHY_OFFSET	0x1c
-
-#define TSEC1_PHY_ADDR		0
-#define TSEC3_PHY_ADDR		1
-
-#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX		0
-#define TSEC3_PHYIDX		0
-
-#define CONFIG_ETHPRIME		"eTSEC1"
-#endif	/* CONFIG_TSEC_ENET */
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/*
- * USB
- */
-
-#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_PCI_EHCI_DEVICE			0
-#endif
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_HAS_ETH0
-#define CONFIG_HAS_ETH1
-#endif
-
-#define CONFIG_IPADDR	192.168.1.251
-
-#define CONFIG_HOSTNAME	"8544ds_unknown"
-#define CONFIG_ROOTPATH	"/nfs/mpc85xx"
-#define CONFIG_BOOTFILE	"8544ds/uImage.uboot"
-#define CONFIG_UBOOTPATH	8544ds/u-boot.bin	/* TFTP server */
-
-#define CONFIG_SERVERIP	192.168.1.1
-#define CONFIG_GATEWAYIP 192.168.1.1
-#define CONFIG_NETMASK	255.255.0.0
-
-#define CONFIG_LOADADDR	1000000	/*default location for tftp and bootm*/
-
-#define	CONFIG_EXTRA_ENV_SETTINGS				\
-"netdev=eth0\0"						\
-"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
-"tftpflash=tftpboot $loadaddr $uboot; "			\
-	"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
-		" +$filesize; "	\
-	"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
-		" +$filesize; "	\
-	"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
-		" $filesize; "	\
-	"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
-		" +$filesize; "	\
-	"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
-		" $filesize\0"	\
-"consoledev=ttyS0\0"				\
-"ramdiskaddr=2000000\0"			\
-"ramdiskfile=8544ds/ramdisk.uboot\0"		\
-"fdtaddr=1e00000\0"				\
-"fdtfile=8544ds/mpc8544ds.dtb\0"		\
-"bdev=sda3\0"
-
-#define CONFIG_NFSBOOTCOMMAND		\
- "setenv bootargs root=/dev/nfs rw "	\
- "nfsroot=$serverip:$rootpath "		\
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;"	\
- "tftp $loadaddr $bootfile;"		\
- "tftp $fdtaddr $fdtfile;"		\
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND		\
- "setenv bootargs root=/dev/ram rw "	\
- "console=$consoledev,$baudrate $othbootargs;"	\
- "tftp $ramdiskaddr $ramdiskfile;"	\
- "tftp $loadaddr $bootfile;"		\
- "tftp $fdtaddr $fdtfile;"		\
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND		\
- "setenv bootargs root=/dev/$bdev rw "	\
- "console=$consoledev,$baudrate $othbootargs;"	\
- "tftp $loadaddr $bootfile;"		\
- "tftp $fdtaddr $fdtfile;"		\
- "bootm $loadaddr - $fdtaddr"
-
-#endif	/* __CONFIG_H */