ppc4xx: Remove 4xx NAND booting support

As ppc4xx currently only supports the deprecated nand_spl infrastructure
and nobody seems to have time / resources to port this over to the newer
SPL infrastructure, lets remove NAND booting completely.

This should not affect the "normal", non NAND-booting ppc4xx platforms
that are currently supported.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Tested-by: Matthias Fuchs <matthias.fuchs@esd.eu>

8 files changed, 4 insertions, 483 deletions

diff --git a/include/configs/PMC440.h b/include/configs/PMC440.h
index fd39109dafe..c5e2f164ce0 100644
--- a/include/configs/PMC440.h
+++ b/include/configs/PMC440.h
@@ -95,12 +95,7 @@
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_ENV_IS_IN_EEPROM	1	/* use FLASH for environment vars */
-#else
-#define CONFIG_ENV_IS_IN_NAND	1	/* use NAND for environment vars */
-#define CONFIG_ENV_IS_EMBEDDED	1	/* use embedded environment */
-#endif
 
 /*-----------------------------------------------------------------------
  * RTC
@@ -142,69 +137,10 @@
 #define CONFIG_ENV_SIZE		0x1000	/* 4096 bytes may be used for env vars */
 #endif
 
-/*
- * IPL (Initial Program Loader, integrated inside CPU)
- * Will load first 4k from NAND (SPL) into cache and execute it from there.
- *
- * SPL (Secondary Program Loader)
- * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
- * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
- * controller and the NAND controller so that the special U-Boot image can be
- * loaded from NAND to SDRAM.
- *
- * NUB (NAND U-Boot)
- * This NAND U-Boot (NUB) is a special U-Boot version which can be started
- * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
- *
- * On 440EPx the SPL is copied to SDRAM before the NAND controller is
- * set up. While still running from cache, I experienced problems accessing
- * the NAND controller.	sr - 2006-08-25
- */
-#if defined (CONFIG_NAND_U_BOOT)
-#define CONFIG_SYS_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location                 */
-#define CONFIG_SYS_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size                     */
-#define CONFIG_SYS_NAND_BOOT_SPL_DST	(CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here    */
-#define CONFIG_SYS_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr        */
-#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr */
-#define CONFIG_SYS_NAND_BOOT_SPL_DELTA	(CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
-
-/*
- * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
- */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS	(16 << 10)	/* Offset to RAM U-Boot image   */
-#define CONFIG_SYS_NAND_U_BOOT_SIZE	(384 << 10)	/* Size of RAM U-Boot image     */
-
-/*
- * Now the NAND chip has to be defined (no autodetection used!)
- */
-#define CONFIG_SYS_NAND_PAGE_SIZE	512	/* NAND chip page size          */
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 << 10) /* NAND chip block size      */
-#define CONFIG_SYS_NAND_PAGE_COUNT	32	/* NAND chip page count         */
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS	5	/* Location of bad block marker */
-#undef CONFIG_SYS_NAND_4_ADDR_CYCLE		/* No fourth addr used (<=32MB) */
-
-#define CONFIG_SYS_NAND_ECCSIZE	256
-#define CONFIG_SYS_NAND_ECCBYTES	3
-#define CONFIG_SYS_NAND_OOBSIZE	16
-#define CONFIG_SYS_NAND_ECCPOS		{0, 1, 2, 3, 6, 7}
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_NAND
-/*
- * For NAND booting the environment is embedded in the U-Boot image. Please take
- * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
- */
-#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET		(CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#endif
-
 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_DDR_DATA_EYE	/* use DDR2 optimization        */
-#endif
 #define CONFIG_SYS_MEM_TOP_HIDE	(4 << 10) /* don't use last 4kbytes */
 						  /* 440EPx errata CHIP 11 */
 
@@ -448,7 +384,6 @@
 /*
  * On Sequoia CS0 and CS3 are switched when configuring for NAND booting
  */
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_SYS_NAND_CS		2	/* NAND chip connected to CSx   */
 
 /* Memory Bank 0 (NOR-FLASH) initialization */
@@ -458,16 +393,6 @@
 /* Memory Bank 2 (NAND-FLASH) initialization */
 #define CONFIG_SYS_EBC_PB2AP		0x018003c0
 #define CONFIG_SYS_EBC_PB2CR		(CONFIG_SYS_NAND_ADDR | 0x1c000)
-#else
-#define CONFIG_SYS_NAND_CS		0	/* NAND chip connected to CSx   */
-/* Memory Bank 2 (NOR-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB2AP		0x03017200
-#define CONFIG_SYS_EBC_PB2CR		(CONFIG_SYS_FLASH_BASE | 0xda000)
-
-/* Memory Bank 0 (NAND-FLASH) initialization */
-#define CONFIG_SYS_EBC_PB0AP		0x018003c0
-#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_NAND_ADDR | 0x1c000)
-#endif
 
 /* Memory Bank 1 (RESET) initialization */
 #define CONFIG_SYS_EBC_PB1AP		0x7f817200 /* 0x03017200 */
diff --git a/include/configs/acadia.h b/include/configs/acadia.h
index 5f3b5f936f1..4dd5720d2f5 100644
--- a/include/configs/acadia.h
+++ b/include/configs/acadia.h
@@ -82,17 +82,11 @@
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
-#else
-#define CONFIG_ENV_IS_IN_NAND	1	/* use NAND for environment vars	*/
-#define CONFIG_ENV_IS_EMBEDDED	1	/* use embedded environment */
-#endif
 
 /*-----------------------------------------------------------------------
  * FLASH related
  *----------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_SYS_FLASH_CFI			/* The flash is CFI compatible	*/
 #define CONFIG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/
 
@@ -106,16 +100,6 @@
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
 #define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#else
-/*
- * No NOR-flash on Acadia when NAND-booting. We need to undef the
- * NOR device-tree fixup code as well, since flash_info is not defined
- * in this case.
- */
-#define	CONFIG_SYS_NO_FLASH		1
-#undef CONFIG_FDT_FIXUP_NOR_FLASH_SIZE
-#endif
-
 #ifdef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SECT_SIZE	0x40000 /* size of one complete sector	*/
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
@@ -126,61 +110,6 @@
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
 #endif
 
-/*
- * IPL (Initial Program Loader, integrated inside CPU)
- * Will load first 4k from NAND (SPL) into cache and execute it from there.
- *
- * SPL (Secondary Program Loader)
- * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
- * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
- * controller and the NAND controller so that the special U-Boot image can be
- * loaded from NAND to SDRAM.
- *
- * NUB (NAND U-Boot)
- * This NAND U-Boot (NUB) is a special U-Boot version which can be started
- * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
- *
- * On 440EPx the SPL is copied to SDRAM before the NAND controller is
- * set up. While still running from cache, I experienced problems accessing
- * the NAND controller.	sr - 2006-08-25
- */
-#define CONFIG_SYS_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location			*/
-#define CONFIG_SYS_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size			*/
-#define CONFIG_SYS_NAND_BOOT_SPL_DST	(CONFIG_SYS_OCM_DATA_ADDR + (16 << 10)) /* Copy SPL here*/
-#define CONFIG_SYS_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr	*/
-#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr	*/
-#define CONFIG_SYS_NAND_BOOT_SPL_DELTA	(CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
-
-/*
- * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
- */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS	(16 << 10)	/* Offset to RAM U-Boot image	*/
-#define CONFIG_SYS_NAND_U_BOOT_SIZE	(384 << 10)	/* Size of RAM U-Boot image	*/
-
-/*
- * Now the NAND chip has to be defined (no autodetection used!)
- */
-#define CONFIG_SYS_NAND_PAGE_SIZE	512		/* NAND chip page size		*/
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 << 10)	/* NAND chip block size		*/
-#define CONFIG_SYS_NAND_PAGE_COUNT	32		/* NAND chip page count		*/
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS	5		/* Location of bad block marker	*/
-#undef CONFIG_SYS_NAND_4_ADDR_CYCLE			/* No fourth addr used (<=32MB)	*/
-
-#define CONFIG_SYS_NAND_ECCSIZE	256
-#define CONFIG_SYS_NAND_ECCBYTES	3
-#define CONFIG_SYS_NAND_OOBSIZE	16
-#define CONFIG_SYS_NAND_ECCPOS		{0, 1, 2, 3, 6, 7}
-
-#ifdef CONFIG_ENV_IS_IN_NAND
-/*
- * For NAND booting the environment is embedded in the U-Boot image. Please take
- * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
- */
-#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET		(CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#endif
-
 /*-----------------------------------------------------------------------
  * RAM (CRAM)
  *----------------------------------------------------------------------*/
@@ -219,7 +148,6 @@
 	CONFIG_AMCC_DEF_ENV_POWERPC					\
 	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
 	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
-	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"kernel_addr=fff10000\0"					\
 	"ramdisk_addr=fff20000\0"					\
 	"kozio=bootm ffc60000\0"					\
@@ -242,14 +170,6 @@
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_USB
 
-/*
- * No NOR on Acadia when NAND-booting
- */
-#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-#undef CONFIG_CMD_FLASH
-#undef CONFIG_CMD_IMLS
-#endif
-
 /*-----------------------------------------------------------------------
  * NAND FLASH
  *----------------------------------------------------------------------*/
@@ -260,7 +180,6 @@
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_SYS_NAND_CS		3
 /* Memory Bank 0 (Flash) initialization						*/
 #define CONFIG_SYS_EBC_PB0AP		0x03337200
@@ -278,24 +197,6 @@
 /* Memory Bank 2 (CRAM) initialization						*/
 #define CONFIG_SYS_EBC_PB2AP		0x030400c0
 #define CONFIG_SYS_EBC_PB2CR		0x020bc000
-#else
-#define CONFIG_SYS_NAND_CS		0		/* NAND chip connected to CSx	*/
-/* Memory Bank 0 (NAND-FLASH) initialization					*/
-#define CONFIG_SYS_EBC_PB0AP		0x018003c0
-#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_NAND_ADDR | 0x1c000)
-
-/*
- * When NAND-booting the CRAM EBC setup must be done in sync mode, since the
- * NAND-SPL already initialized the CRAM and EBC to sync mode.
- */
-/* Memory Bank 1 (CRAM) initialization						*/
-#define CONFIG_SYS_EBC_PB1AP		0x9C0201C0
-#define CONFIG_SYS_EBC_PB1CR		0x000bc000
-
-/* Memory Bank 2 (CRAM) initialization						*/
-#define CONFIG_SYS_EBC_PB2AP		0x9C0201C0
-#define CONFIG_SYS_EBC_PB2CR		0x020bc000
-#endif
 
 /* Memory Bank 4 (CPLD) initialization						*/
 #define CONFIG_SYS_EBC_PB4AP		0x04006000
diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h
index 0f38c92fa06..2aea89937a2 100644
--- a/include/configs/amcc-common.h
+++ b/include/configs/amcc-common.h
@@ -253,10 +253,4 @@
 		"cp.b ${fileaddr} " __stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
 	"upd=run load update\0"						\
 
-#define CONFIG_AMCC_DEF_ENV_NAND_UPD					\
-	"u-boot-nand=" __stringify(CONFIG_HOSTNAME) "/u-boot-nand.bin\0"\
-	"nload=tftp 200000 ${u-boot-nand}\0"				\
-	"nupdate=nand erase 0 100000;nand write 200000 0 100000\0"	\
-	"nupd=run nload nupdate\0"
-
 #endif /* __AMCC_COMMON_H */
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
index 97da1e9078a..6ba4aaf8cb7 100644
--- a/include/configs/bamboo.h
+++ b/include/configs/bamboo.h
@@ -86,12 +86,7 @@
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
-#else
-#define CONFIG_ENV_IS_IN_NAND	1	/* use NAND for environment vars	*/
-#define CONFIG_ENV_IS_EMBEDDED	1	/* use embedded environment */
-#endif
 
 /*-----------------------------------------------------------------------
  * FLASH related
@@ -120,61 +115,6 @@
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
 #endif /* CONFIG_ENV_IS_IN_FLASH */
 
-/*
- * IPL (Initial Program Loader, integrated inside CPU)
- * Will load first 4k from NAND (SPL) into cache and execute it from there.
- *
- * SPL (Secondary Program Loader)
- * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
- * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
- * controller and the NAND controller so that the special U-Boot image can be
- * loaded from NAND to SDRAM.
- *
- * NUB (NAND U-Boot)
- * This NAND U-Boot (NUB) is a special U-Boot version which can be started
- * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
- *
- * On 440EPx the SPL is copied to SDRAM before the NAND controller is
- * set up. While still running from cache, I experienced problems accessing
- * the NAND controller.	sr - 2006-08-25
- */
-#define CONFIG_SYS_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location			*/
-#define CONFIG_SYS_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size			*/
-#define CONFIG_SYS_NAND_BOOT_SPL_DST	0x00800000	/* Copy SPL here		*/
-#define CONFIG_SYS_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr	*/
-#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr	*/
-#define CONFIG_SYS_NAND_BOOT_SPL_DELTA	(CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
-
-/*
- * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
- */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS	(16 << 10)	/* Offset to RAM U-Boot image	*/
-#define CONFIG_SYS_NAND_U_BOOT_SIZE	(384 << 10)	/* Size of RAM U-Boot image	*/
-
-/*
- * Now the NAND chip has to be defined (no autodetection used!)
- */
-#define CONFIG_SYS_NAND_PAGE_SIZE	512		/* NAND chip page size		*/
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 << 10)	/* NAND chip block size		*/
-#define CONFIG_SYS_NAND_PAGE_COUNT	32		/* NAND chip page count		*/
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS	5		/* Location of bad block marker	*/
-#define CONFIG_SYS_NAND_4_ADDR_CYCLE	1		/* Fourth addr used (>32MB)	*/
-
-#define CONFIG_SYS_NAND_ECCSIZE	256
-#define CONFIG_SYS_NAND_ECCBYTES	3
-#define CONFIG_SYS_NAND_OOBSIZE	16
-#define CONFIG_SYS_NAND_ECCPOS		{0, 1, 2, 3, 6, 7}
-
-#ifdef CONFIG_ENV_IS_IN_NAND
-/*
- * For NAND booting the environment is embedded in the U-Boot image. Please take
- * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
- */
-#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET		(CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#endif
-
 /*-----------------------------------------------------------------------
  * NAND FLASH
  *----------------------------------------------------------------------*/
@@ -182,15 +122,7 @@
 #define CONFIG_SYS_NAND_BASE		(CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_ADDR + 2 }
 #define CONFIG_SYS_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/
-
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_SYS_NAND_CS		1
-#else
-#define CONFIG_SYS_NAND_CS		0		/* NAND chip connected to CSx	*/
-/* Memory Bank 0 (NAND-FLASH) initialization					*/
-#define CONFIG_SYS_EBC_PB0AP		0x018003c0
-#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_NAND_ADDR | 0x1c000)
-#endif
 
 /*-----------------------------------------------------------------------
  * DDR SDRAM
@@ -226,7 +158,6 @@
 	CONFIG_AMCC_DEF_ENV_POWERPC					\
 	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
 	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
-	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"kernel_addr=fff00000\0"					\
 	"ramdisk_addr=fff10000\0"					\
 	""
diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h
index 620a0f5c571..8eeb15c0e10 100644
--- a/include/configs/canyonlands.h
+++ b/include/configs/canyonlands.h
@@ -125,78 +125,9 @@
 /*
  * Define here the location of the environment variables (FLASH).
  */
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define	CONFIG_ENV_IS_IN_FLASH	1	/* use FLASH for environment vars */
 #define CONFIG_SYS_NOR_CS		0	/* NOR chip connected to CSx */
 #define CONFIG_SYS_NAND_CS		3	/* NAND chip connected to CSx */
-#else
-#define	CONFIG_ENV_IS_IN_NAND	1	/* use NAND for environment vars  */
-#define CONFIG_SYS_NOR_CS		3	/* NOR chip connected to CSx */
-#define CONFIG_SYS_NAND_CS		0	/* NAND chip connected to CSx */
-#define CONFIG_ENV_IS_EMBEDDED	1	/* use embedded environment */
-#endif
-
-/*
- * IPL (Initial Program Loader, integrated inside CPU)
- * Will load first 4k from NAND (SPL) into cache and execute it from there.
- *
- * SPL (Secondary Program Loader)
- * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
- * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
- * controller and the NAND controller so that the special U-Boot image can be
- * loaded from NAND to SDRAM.
- *
- * NUB (NAND U-Boot)
- * This NAND U-Boot (NUB) is a special U-Boot version which can be started
- * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
- *
- * On 440EPx the SPL is copied to SDRAM before the NAND controller is
- * set up. While still running from cache, I experienced problems accessing
- * the NAND controller.	sr - 2006-08-25
- *
- * This is the first official implementation of booting from 2k page sized
- * NAND devices (e.g. Micron 29F2G08AA 256Mbit * 8)
- */
-#define CONFIG_SYS_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location		      */
-#define CONFIG_SYS_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size		      */
-#define CONFIG_SYS_NAND_BOOT_SPL_DST	(CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here  */
-#define CONFIG_SYS_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr      */
-#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST	/* Start NUB from     */
-							/*   this addr	      */
-#define CONFIG_SYS_NAND_BOOT_SPL_DELTA	(CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
-
-/*
- * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
- */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS	(128 << 10)	/* Offset to RAM U-Boot image */
-#define CONFIG_SYS_NAND_U_BOOT_SIZE	(1 << 20)	/* Size of RAM U-Boot image   */
-
-/*
- * Now the NAND chip has to be defined (no autodetection used!)
- */
-#define CONFIG_SYS_NAND_PAGE_SIZE	(2 << 10)	/* NAND chip page size	      */
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)	/* NAND chip block size	      */
-#define CONFIG_SYS_NAND_PAGE_COUNT	(CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE)
-						/* NAND chip page count	      */
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS	0		/* Location of bad block marker*/
-#define CONFIG_SYS_NAND_5_ADDR_CYCLE			/* Fifth addr used (<=128MB)  */
-
-#define CONFIG_SYS_NAND_ECCSIZE	256
-#define CONFIG_SYS_NAND_ECCBYTES	3
-#define CONFIG_SYS_NAND_OOBSIZE	64
-#define CONFIG_SYS_NAND_ECCPOS		{40, 41, 42, 43, 44, 45, 46, 47, \
-				 48, 49, 50, 51, 52, 53, 54, 55, \
-				 56, 57, 58, 59, 60, 61, 62, 63}
-
-#ifdef CONFIG_ENV_IS_IN_NAND
-/*
- * For NAND booting the environment is embedded in the U-Boot image. Please take
- * look at the file board/amcc/canyonlands/u-boot-nand.lds for details.
- */
-#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET		(CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#endif
 
 /*-----------------------------------------------------------------------
  * FLASH related
@@ -235,7 +166,6 @@
 /*------------------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT)
 #if !defined(CONFIG_ARCHES)
 /*
  * NAND booting U-Boot version uses a fixed initialization, since the whole
@@ -308,7 +238,6 @@
 #define CONFIG_SYS_SDRAM0_MMODE		0x00000432
 #define CONFIG_SYS_SDRAM0_MEMODE	0x00000004
 #endif	/* !defined(CONFIG_ARCHES) */
-#endif	/* !defined(CONFIG_NAND_U_BOOT) */
 
 #define CONFIG_SYS_MBYTES_SDRAM	512	/* 512MB			*/
 
@@ -421,7 +350,6 @@
 	CONFIG_AMCC_DEF_ENV						\
 	CONFIG_AMCC_DEF_ENV_POWERPC					\
 	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
-	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"fdt_addr=fc1e0000\0"						\
 	"ramdisk_addr=fc200000\0"					\
@@ -556,15 +484,6 @@
  * 0xfe00.0000 -> 4.ce00.0000
  */
 
-#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-/* Memory Bank 3 (NOR-FLASH) initialization					*/
-#define CONFIG_SYS_EBC_PB3AP		0x10055e00
-#define CONFIG_SYS_EBC_PB3CR		(CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000)
-
-/* Memory Bank 0 (NAND-FLASH) initialization						*/
-#define CONFIG_SYS_EBC_PB0AP		0x018003c0
-#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/
-#else
 /* Memory Bank 0 (NOR-FLASH) initialization					*/
 #define CONFIG_SYS_EBC_PB0AP		0x10055e00
 #define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_BOOT_BASE_ADDR | 0x9a000)
@@ -574,7 +493,6 @@
 #define CONFIG_SYS_EBC_PB3AP		0x018003c0
 #define CONFIG_SYS_EBC_PB3CR		(CONFIG_SYS_NAND_ADDR | 0x1E000) /* BAS=NAND,BS=1MB,BU=R/W,BW=32bit*/
 #endif
-#endif	/*defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL) */
 
 #if !defined(CONFIG_ARCHES)
 /* Memory Bank 2 (CPLD) initialization						*/
diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 0695d2d37b1..1990b2df150 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -118,12 +118,7 @@
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CONFIG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
-#else
-#define CONFIG_ENV_IS_IN_NAND	1	/* use NAND for environment vars	*/
-#define CONFIG_ENV_IS_EMBEDDED	1	/* use embedded environment */
-#endif
 
 /*-----------------------------------------------------------------------
  * FLASH related
@@ -151,61 +146,6 @@
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
 #endif /* CONFIG_ENV_IS_IN_FLASH */
 
-/*
- * IPL (Initial Program Loader, integrated inside CPU)
- * Will load first 4k from NAND (SPL) into cache and execute it from there.
- *
- * SPL (Secondary Program Loader)
- * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
- * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
- * controller and the NAND controller so that the special U-Boot image can be
- * loaded from NAND to SDRAM.
- *
- * NUB (NAND U-Boot)
- * This NAND U-Boot (NUB) is a special U-Boot version which can be started
- * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
- *
- * On 405EX the SPL is copied to SDRAM before the NAND controller is
- * set up. While still running from location 0xfffff000...0xffffffff the
- * NAND controller cannot be accessed since it is attached to CS0 too.
- */
-#define CONFIG_SYS_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location			*/
-#define CONFIG_SYS_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size			*/
-#define CONFIG_SYS_NAND_BOOT_SPL_DST	0x00800000	/* Copy SPL here		*/
-#define CONFIG_SYS_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr	*/
-#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST /* Start NUB from this addr	*/
-#define CONFIG_SYS_NAND_BOOT_SPL_DELTA	(CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
-
-/*
- * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
- */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS	(16 << 10)	/* Offset to RAM U-Boot image	*/
-#define CONFIG_SYS_NAND_U_BOOT_SIZE	(384 << 10)	/* Size of RAM U-Boot image	*/
-
-/*
- * Now the NAND chip has to be defined (no autodetection used!)
- */
-#define CONFIG_SYS_NAND_PAGE_SIZE	512		/* NAND chip page size		*/
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 << 10)	/* NAND chip block size		*/
-#define CONFIG_SYS_NAND_PAGE_COUNT	32		/* NAND chip page count		*/
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS	5		/* Location of bad block marker	*/
-#define CONFIG_SYS_NAND_4_ADDR_CYCLE	1		/* Fourth addr used (>32MB)	*/
-
-#define CONFIG_SYS_NAND_ECCSIZE	256
-#define CONFIG_SYS_NAND_ECCBYTES	3
-#define CONFIG_SYS_NAND_OOBSIZE	16
-#define CONFIG_SYS_NAND_ECCPOS		{0, 1, 2, 3, 6, 7}
-
-#ifdef CONFIG_ENV_IS_IN_NAND
-/*
- * For NAND booting the environment is embedded in the U-Boot image. Please take
- * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
- */
-#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET		(CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#endif
-
 /*-----------------------------------------------------------------------
  * NAND FLASH
  *----------------------------------------------------------------------*/
@@ -230,11 +170,9 @@
  *
  * DDR Autocalibration Method_B is the default.
  */
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define	CONFIG_PPC4xx_DDR_AUTOCALIBRATION	/* IBM DDR autocalibration */
 #define	DEBUG_PPC4xx_DDR_AUTOCALIBRATION	/* dynamic DDR autocal debug */
 #undef	CONFIG_PPC4xx_DDR_METHOD_A
-#endif
 
 #define	CONFIG_SYS_SDRAM0_MB0CF_BASE	((  0 << 20) + CONFIG_SYS_SDRAM_BASE)
 
@@ -416,7 +354,6 @@
 	CONFIG_AMCC_DEF_ENV_POWERPC					\
 	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
 	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
-	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"logversion=2\0"						\
 	"kernel_addr=fc000000\0"					\
 	"fdt_addr=fc1e0000\0"						\
@@ -434,16 +371,7 @@
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_SNTP
 
-/*
- * Don't run the memory POST on the NAND-booting version. It will
- * overwrite part of the U-Boot image which is already loaded from NAND
- * to SDRAM.
- */
-#if defined(CONFIG_NAND_U_BOOT)
-#define CONFIG_SYS_POST_MEMORY_ON	0
-#else
 #define CONFIG_SYS_POST_MEMORY_ON	CONFIG_SYS_POST_MEMORY
-#endif
 
 /* POST support */
 #define CONFIG_POST		(CONFIG_SYS_POST_CACHE		| \
@@ -494,18 +422,6 @@
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
-#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-/* booting from NAND, so NAND chips select has to be on CS 0 */
-#define CONFIG_SYS_NAND_CS		0		/* NAND chip connected to CSx	*/
-
-/* Memory Bank 1 (NOR-FLASH) initialization					*/
-#define CONFIG_SYS_EBC_PB1AP		0x05806500
-#define CONFIG_SYS_EBC_PB1CR           0xFC0DA000  /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit*/
-
-/* Memory Bank 0 (NAND-FLASH) initialization					*/
-#define CONFIG_SYS_EBC_PB0AP		0x018003c0
-#define CONFIG_SYS_EBC_PB0CR		(CONFIG_SYS_NAND_ADDR | 0x1e000)
-#else
 #define CONFIG_SYS_NAND_CS		1		/* NAND chip connected to CSx	*/
 
 /* Memory Bank 0 (NOR-FLASH) initialization					*/
@@ -515,7 +431,6 @@
 /* Memory Bank 1 (NAND-FLASH) initialization					*/
 #define CONFIG_SYS_EBC_PB1AP		0x018003c0
 #define CONFIG_SYS_EBC_PB1CR		(CONFIG_SYS_NAND_ADDR | 0x1e000)
-#endif
 
 /* Memory Bank 2 (FPGA) initialization					*/
 #define CONFIG_SYS_EBC_PB2AP		(EBC_BXAP_BME_ENABLED |		\
diff --git a/include/configs/redwood.h b/include/configs/redwood.h
index 84d1e584a03..622b7c79e64 100644
--- a/include/configs/redwood.h
+++ b/include/configs/redwood.h
@@ -120,7 +120,6 @@
 	CONFIG_AMCC_DEF_ENV						\
 	CONFIG_AMCC_DEF_ENV_POWERPC					\
 	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
-	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"fdt_addr=fc1e0000\0"						\
 	"ramdisk_addr=fc200000\0"					\
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 0e21ee3dc08..b6a5e6a59c9 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -97,10 +97,7 @@
 /*
  * Environment
  */
-#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
-#define CONFIG_ENV_IS_IN_NAND		/* use NAND for environ vars	*/
-#define CONFIG_ENV_IS_EMBEDDED		/* use embedded environment	*/
-#elif defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
 #define CONFIG_ENV_IS_NOWHERE		/* Store env in memory only	*/
 #define CONFIG_ENV_SIZE		(8 << 10)
 /*
@@ -149,67 +146,10 @@
 #endif /* CONFIG_CMD_FLASH */
 
 /*
- * IPL (Initial Program Loader, integrated inside CPU)
- * Will load first 4k from NAND (SPL) into cache and execute it from there.
- *
- * SPL (Secondary Program Loader)
- * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
- * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
- * controller and the NAND controller so that the special U-Boot image can be
- * loaded from NAND to SDRAM.
- *
- * NUB (NAND U-Boot)
- * This NAND U-Boot (NUB) is a special U-Boot version which can be started
- * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
- *
- * On 440EPx the SPL is copied to SDRAM before the NAND controller is
- * set up. While still running from cache, I experienced problems accessing
- * the NAND controller.	sr - 2006-08-25
- */
-#define CONFIG_SYS_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location		      */
-#define CONFIG_SYS_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size		      */
-#define CONFIG_SYS_NAND_BOOT_SPL_DST	(CONFIG_SYS_OCM_BASE + (12 << 10)) /* Copy SPL here  */
-#define CONFIG_SYS_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr      */
-#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST	/* Start NUB from     */
-							/*   this addr	      */
-#define CONFIG_SYS_NAND_BOOT_SPL_DELTA	(CONFIG_SYS_NAND_BOOT_SPL_SRC - CONFIG_SYS_NAND_BOOT_SPL_DST)
-
-/*
- * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
- */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS	(16 << 10)	/* Offset to RAM U-Boot image */
-#define CONFIG_SYS_NAND_U_BOOT_SIZE	(512 << 10)	/* Size of RAM U-Boot image   */
-
-/*
- * Now the NAND chip has to be defined (no autodetection used!)
- */
-#define CONFIG_SYS_NAND_PAGE_SIZE	512		/* NAND chip page size	      */
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(16 << 10)	/* NAND chip block size	      */
-#define CONFIG_SYS_NAND_PAGE_COUNT	32		/* NAND chip page count	      */
-#define CONFIG_SYS_NAND_BAD_BLOCK_POS	5	      /* Location of bad block marker */
-#undef CONFIG_SYS_NAND_4_ADDR_CYCLE		      /* No fourth addr used (<=32MB) */
-
-#define CONFIG_SYS_NAND_ECCSIZE	256
-#define CONFIG_SYS_NAND_ECCBYTES	3
-#define CONFIG_SYS_NAND_OOBSIZE	16
-#define CONFIG_SYS_NAND_ECCPOS		{0, 1, 2, 3, 6, 7}
-
-#ifdef CONFIG_ENV_IS_IN_NAND
-/*
- * For NAND booting the environment is embedded in the U-Boot image. Please take
- * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
- */
-#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET		(CONFIG_SYS_NAND_U_BOOT_OFFS + CONFIG_ENV_SIZE)
-#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
-#endif
-
-/*
  * DDR SDRAM
  */
 #define CONFIG_SYS_MBYTES_SDRAM        (256)	/* 256MB			*/
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) && \
-    !defined(CONFIG_SYS_RAMBOOT)
+#if !defined(CONFIG_SYS_RAMBOOT)
 #define CONFIG_DDR_DATA_EYE		/* use DDR2 optimization	*/
 #endif
 #define CONFIG_SYS_MEM_TOP_HIDE	(4 << 10) /* don't use last 4kbytes	*/
@@ -247,7 +187,6 @@
 	CONFIG_AMCC_DEF_ENV_POWERPC					\
 	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
 	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
-	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"kernel_addr=FC000000\0"					\
 	"ramdisk_addr=FC180000\0"					\
 	""
@@ -321,7 +260,7 @@
  * overwrite part of the U-Boot image which is already loaded from NAND
  * to SDRAM.
  */
-#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
 #define CONFIG_SYS_POST_MEMORY_ON	0
 #else
 #define CONFIG_SYS_POST_MEMORY_ON	CONFIG_SYS_POST_MEMORY
@@ -370,8 +309,7 @@
 /*
  * On Sequoia CS0 and CS3 are switched when configuring for NAND booting
  */
-#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL) && \
-    !defined(CONFIG_SYS_RAMBOOT)
+#if !defined(CONFIG_SYS_RAMBOOT)
 #define CONFIG_SYS_NAND_CS		3	/* NAND chip connected to CSx	*/
 /* Memory Bank 0 (NOR-FLASH) initialization				*/
 #define CONFIG_SYS_EBC_PB0AP		0x03017200