ppc: Remove MPC8349ITX board

This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI.  The
deadline for this conversion was the v2019.07 release.  The use of CONFIG_AHCI
requires CONFIG_DM.  The deadline for this conversion was v2020.01.  Remove
this board.

Signed-off-by: Tom Rini <trini@konsulko.com>

1 files changed, 0 insertions, 439 deletions

diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h
deleted file mode 100644
index 586c1e9ae84..00000000000
--- a/include/configs/MPC8349ITX.h
+++ /dev/null
@@ -1,439 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) Freescale Semiconductor, Inc. 2006.
- */
-
-/*
- MPC8349E-mITX and MPC8349E-mITX-GP board configuration file
-
- Memory map:
-
- 0x0000_0000-0x0FFF_FFFF DDR SDRAM (256 MB)
- 0x8000_0000-0x9FFF_FFFF PCI1 memory space (512 MB)
- 0xA000_0000-0xBFFF_FFFF PCI2 memory space (512 MB)
- 0xE000_0000-0xEFFF_FFFF IMMR (1 MB)
- 0xE200_0000-0xE2FF_FFFF PCI1 I/O space (16 MB)
- 0xE300_0000-0xE3FF_FFFF PCI2 I/O space (16 MB)
- 0xF000_0000-0xF000_FFFF Compact Flash (MPC8349E-mITX only)
- 0xF001_0000-0xF001_FFFF Local bus expansion slot
- 0xF800_0000-0xF801_FFFF Vitesse 7385 Parallel Interface (MPC8349E-mITX only)
- 0xFE00_0000-0xFE7F_FFFF First 8MB bank of Flash memory
- 0xFE80_0000-0xFEFF_FFFF Second 8MB bank of Flash memory (MPC8349E-mITX only)
-
- I2C address list:
-						Align.	Board
- Bus	Addr	Part No.	Description	Length	Location
- ----------------------------------------------------------------
- I2C0	0x50	M24256-BWMN6P	Board EEPROM	2	U64
-
- I2C1	0x20	PCF8574		I2C Expander	0	U8
- I2C1	0x21	PCF8574		I2C Expander	0	U10
- I2C1	0x38	PCF8574A	I2C Expander	0	U8
- I2C1	0x39	PCF8574A	I2C Expander	0	U10
- I2C1	0x51	(DDR)		DDR EEPROM	1	U1
- I2C1	0x68	DS1339		RTC		1	U68
-
- Note that a given board has *either* a pair of 8574s or a pair of 8574As.
-*/
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * On-board devices
- */
-
-#ifdef CONFIG_TARGET_MPC8349ITX
-/* The CF card interface on the back of the board */
-#define CONFIG_COMPACT_FLASH
-#define CONFIG_VSC7385_ENET	/* VSC7385 ethernet support */
-#define CONFIG_SYS_USB_HOST	/* use the EHCI USB controller */
-#endif
-
-#include <linux/stringify.h>
-#define CONFIG_RTC_DS1337
-#define CONFIG_SYS_I2C
-
-/*
- * Device configurations
- */
-
-/* I2C */
-#ifdef CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-
-#define CONFIG_SYS_SPD_BUS_NUM		1	/* The I2C bus for SPD */
-#define CONFIG_SYS_RTC_BUS_NUM		1	/* The I2C bus for RTC */
-
-#define CONFIG_SYS_I2C_8574_ADDR1	0x20	/* I2C1, PCF8574 */
-#define CONFIG_SYS_I2C_8574_ADDR2	0x21	/* I2C1, PCF8574 */
-#define CONFIG_SYS_I2C_8574A_ADDR1	0x38	/* I2C1, PCF8574A */
-#define CONFIG_SYS_I2C_8574A_ADDR2	0x39	/* I2C1, PCF8574A */
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* I2C0, Board EEPROM */
-#define CONFIG_SYS_I2C_RTC_ADDR		0x68	/* I2C1, DS1339 RTC*/
-#define SPD_EEPROM_ADDRESS		0x51	/* I2C1, DDR */
-
-/* Don't probe these addresses: */
-#define CONFIG_SYS_I2C_NOPROBES	{ {1, CONFIG_SYS_I2C_8574_ADDR1}, \
-				 {1, CONFIG_SYS_I2C_8574_ADDR2}, \
-				 {1, CONFIG_SYS_I2C_8574A_ADDR1}, \
-				 {1, CONFIG_SYS_I2C_8574A_ADDR2} }
-/* Bit definitions for the 8574[A] I2C expander */
-				/* Board revision, 00=0.0, 01=0.1, 10=1.0 */
-#define I2C_8574_REVISION	0x03
-#define I2C_8574_CF		0x08	/* 1=Compact flash absent, 0=present */
-#define I2C_8574_MPCICLKRN	0x10	/* MiniPCI Clk Run */
-#define I2C_8574_PCI66		0x20	/* 0=33MHz PCI, 1=66MHz PCI */
-#define I2C_8574_FLASHSIDE	0x40	/* 0=Reset vector from U4, 1=from U7*/
-
-#endif
-
-/* Compact Flash */
-#ifdef CONFIG_COMPACT_FLASH
-
-#define CONFIG_SYS_IDE_MAXBUS		1
-#define CONFIG_SYS_IDE_MAXDEVICE	1
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_CF_BASE
-#define CONFIG_SYS_ATA_DATA_OFFSET	0x0000
-#define CONFIG_SYS_ATA_REG_OFFSET	0
-#define CONFIG_SYS_ATA_ALT_OFFSET	0x0200
-#define CONFIG_SYS_ATA_STRIDE		2
-
-/* If a CF card is not inserted, time out quickly */
-#define ATA_RESET_TIME	1
-
-#endif
-
-/*
- * SATA
- */
-#ifdef CONFIG_SATA_SIL3114
-
-#define CONFIG_SYS_SATA_MAX_DEVICE      4
-#define CONFIG_LBA48
-
-#endif
-
-#ifdef CONFIG_SYS_USB_HOST
-/*
- * Support USB
- */
-#define CONFIG_USB_EHCI_FSL
-
-/* Current USB implementation supports the only USB controller,
- * so we have to choose between the MPH or the DR ones */
-#if 1
-#define CONFIG_HAS_FSL_MPH_USB
-#else
-#define CONFIG_HAS_FSL_DR_USB
-#endif
-
-#endif
-
-/*
- * DDR Setup
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_83XX_DDR_USES_CS0
-
-#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN \
-					| DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
-
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_MAX_MEM_MAPPED   ((phys_size_t)256 << 20)
-
-#ifdef CONFIG_SYS_I2C
-#define CONFIG_SPD_EEPROM		/* use SPD EEPROM for DDR setup*/
-#endif
-
-/* No SPD? Then manually set up DDR parameters */
-#ifndef CONFIG_SPD_EEPROM
-    #define CONFIG_SYS_DDR_SIZE		256	/* Mb */
-    #define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN \
-					| CSCONFIG_ROW_BIT_13 \
-					| CSCONFIG_COL_BIT_10)
-
-    #define CONFIG_SYS_DDR_TIMING_1	0x26242321
-    #define CONFIG_SYS_DDR_TIMING_2	0x00000800  /* P9-45, may need tuning */
-#endif
-
-/*
- *Flash on the Local Bus
- */
-
-#define CONFIG_SYS_FLASH_BASE		0xFE000000	/* start of FLASH   */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-/* 127 64KB sectors + 8 8KB sectors per device */
-#define CONFIG_SYS_MAX_FLASH_SECT	135
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
-
-/* The ITX has two flash chips, but the ITX-GP has only one.  To support both
-boards, we say we have two, but don't display a message if we find only one. */
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
-#define CONFIG_SYS_FLASH_BANKS_LIST	\
-		{CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + 0x800000}
-#define CONFIG_SYS_FLASH_SIZE		16	/* FLASH size in MB */
-
-/* Vitesse 7385 */
-
-#ifdef CONFIG_VSC7385_ENET
-
-#define CONFIG_TSEC2
-
-/* The flash address and size of the VSC7385 firmware image */
-#define CONFIG_VSC7385_IMAGE		0xFEFFE000
-#define CONFIG_VSC7385_IMAGE_SIZE	8192
-
-#endif
-
-/*
- * BRx, ORx, LBLAWBARx, and LBLAWARx
- */
-
-
-/* Vitesse 7385 */
-
-#define CONFIG_SYS_VSC7385_BASE	0xF8000000
-
-#define CONFIG_SYS_LED_BASE	0xF9000000
-
-
-/* Compact Flash */
-
-#ifdef CONFIG_COMPACT_FLASH
-
-#define CONFIG_SYS_CF_BASE	0xF0000000
-
-
-#endif
-
-/*
- * U-Boot memory configuration
- */
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#else
-#undef	CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000	/* Initial RAM addr */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000	/* Size of used area in RAM*/
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	\
-			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CONFIG_SYS_MONITOR_LEN	(512 * 1024) /* Reserve 512 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN	(256 * 1024) /* Reserved for malloc */
-
-/*
- * Serial Port
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
-
-#define CONSOLE			ttyS0
-
-#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
-#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
-
-/*
- * PCI
- */
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-
-#define CONFIG_MPC83XX_PCI2
-
-/*
- * General PCI
- * Addresses are mapped 1-1.
- */
-#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
-#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
-#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_MMIO_BASE	\
-			(CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
-#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
-#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI1_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
-#define CONFIG_SYS_PCI1_IO_SIZE		0x01000000	/* 16M */
-
-#ifdef CONFIG_MPC83XX_PCI2
-#define CONFIG_SYS_PCI2_MEM_BASE	\
-			(CONFIG_SYS_PCI1_MMIO_BASE + CONFIG_SYS_PCI1_MMIO_SIZE)
-#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
-#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI2_MMIO_BASE	\
-			(CONFIG_SYS_PCI2_MEM_BASE + CONFIG_SYS_PCI2_MEM_SIZE)
-#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
-#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCI2_IO_BASE		0x00000000
-#define CONFIG_SYS_PCI2_IO_PHYS		\
-			(CONFIG_SYS_PCI1_IO_PHYS + CONFIG_SYS_PCI1_IO_SIZE)
-#define CONFIG_SYS_PCI2_IO_SIZE		0x01000000	/* 16M */
-#endif
-
-#ifndef CONFIG_PCI_PNP
-    #define PCI_ENET0_IOADDR	0x00000000
-    #define PCI_ENET0_MEMADDR	CONFIG_SYS_PCI2_MEM_BASE
-    #define PCI_IDSEL_NUMBER	0x0f	/* IDSEL = AD15 */
-#endif
-
-#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-
-#endif
-
-/* TSEC */
-
-#ifdef CONFIG_TSEC_ENET
-#define CONFIG_TSEC1
-
-#ifdef CONFIG_TSEC1
-#define CONFIG_HAS_ETH0
-#define CONFIG_TSEC1_NAME  "TSEC0"
-#define CONFIG_SYS_TSEC1_OFFSET	0x24000
-#define TSEC1_PHY_ADDR		0x1c	/* VSC8201 uses address 0x1c */
-#define TSEC1_PHYIDX		0
-#define TSEC1_FLAGS		TSEC_GIGABIT
-#endif
-
-#ifdef CONFIG_TSEC2
-#define CONFIG_HAS_ETH1
-#define CONFIG_TSEC2_NAME  "TSEC1"
-#define CONFIG_SYS_TSEC2_OFFSET	0x25000
-
-#define TSEC2_PHY_ADDR		4
-#define TSEC2_PHYIDX		0
-#define TSEC2_FLAGS		TSEC_GIGABIT
-#endif
-
-#define CONFIG_ETHPRIME		"Freescale TSEC"
-
-#endif
-
-/*
- * Environment
- */
-
-#define CONFIG_LOADS_ECHO	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-/* Watchdog */
-#undef CONFIG_WATCHDOG		/* watchdog disabled */
-
-/*
- * Miscellaneous configurable options
- */
-
-#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
-#define CONFIG_LOADADDR	800000	/* default location for tftp and bootm */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 256 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-				/* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTMAPSZ	(256 << 20)
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-/*
- * System performance
- */
-#define CONFIG_SYS_SCCR_TSEC1CM	1	/* TSEC1 clock mode (0-3) */
-#define CONFIG_SYS_SCCR_TSEC2CM	1	/* TSEC2 & I2C0 clock mode (0-3) */
-#define CONFIG_SYS_SCCR_USBMPHCM 3	/* USB MPH controller's clock */
-#define CONFIG_SYS_SCCR_USBDRCM	0	/* USB DR controller's clock */
-
-/*
- * System IO Config
- */
-/* Needed for gigabit to work on TSEC 1 */
-#define CONFIG_SYS_SICRH SICRH_TSOBI1
-				/* USB DR as device + USB MPH as host */
-#define CONFIG_SYS_SICRL	(SICRL_LDP_A | SICRL_USB1)
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
-#endif
-
-/*
- * Environment Configuration
- */
-
-#define CONFIG_NETDEV		"eth0"
-
-/* Default path and filenames */
-#define CONFIG_ROOTPATH		"/nfsroot/rootfs"
-#define CONFIG_BOOTFILE		"uImage"
-				/* U-Boot image on TFTP server */
-#define CONFIG_UBOOTPATH	"u-boot.bin"
-
-#ifdef CONFIG_TARGET_MPC8349ITX
-#define CONFIG_FDTFILE		"mpc8349emitx.dtb"
-#else
-#define CONFIG_FDTFILE		"mpc8349emitxgp.dtb"
-#endif
-
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"console=" __stringify(CONSOLE) "\0"			\
-	"netdev=" CONFIG_NETDEV "\0"					\
-	"uboot=" CONFIG_UBOOTPATH "\0"					\
-	"tftpflash=tftpboot $loadaddr $uboot; "				\
-		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
-			" +$filesize; "	\
-		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
-			" +$filesize; "	\
-		"cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
-			" $filesize; "	\
-		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
-			" +$filesize; "	\
-		"cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)	\
-			" $filesize\0"	\
-	"fdtaddr=780000\0"						\
-	"fdtfile=" CONFIG_FDTFILE "\0"
-
-#define CONFIG_NFSBOOTCOMMAND						\
-	"setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath"	\
-	" ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off "\
-	" console=$console,$baudrate $othbootargs; "			\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND						\
-	"setenv bootargs root=/dev/ram rw"				\
-	" console=$console,$baudrate $othbootargs; "			\
-	"tftp $ramdiskaddr $ramdiskfile;"				\
-	"tftp $loadaddr $bootfile;"					\
-	"tftp $fdtaddr $fdtfile;"					\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#endif