Merge branch 'master' of git://git.denx.de/u-boot-socfpga

3 files changed, 235 insertions, 7 deletions

diff --git a/include/configs/socfpga_common.h b/include/configs/socfpga_common.h
index f6577668a1d..1f8b7b3b80e 100644
--- a/include/configs/socfpga_common.h
+++ b/include/configs/socfpga_common.h
@@ -324,9 +324,6 @@ unsigned int cm_get_qspi_controller_clk_hz(void);
 #define CONFIG_SPL_RAM_DEVICE
 #define CONFIG_SPL_TEXT_BASE		CONFIG_SYS_INIT_RAM_ADDR
 #define CONFIG_SPL_MAX_SIZE		(64 * 1024)
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_MALLOC_SIMPLE
-#endif
 
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
@@ -349,9 +346,9 @@ unsigned int cm_get_qspi_controller_clk_hz(void);
 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot-dtb.img"
 #define CONFIG_SPL_LIBDISK_SUPPORT
 #else
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	3
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0xa00 /* offset 2560 sect (1M+256k) */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	800 /* 400 KB */
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION	3
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x200 /* offset 512 sect (256k) */
+#define CONFIG_SPL_LIBDISK_SUPPORT
 #endif
 #endif
 
diff --git a/include/configs/socfpga_sr1500.h b/include/configs/socfpga_sr1500.h
index efa9e428cee..c097f47edd4 100644
--- a/include/configs/socfpga_sr1500.h
+++ b/include/configs/socfpga_sr1500.h
@@ -22,7 +22,7 @@
 /* Booting Linux */
 #define CONFIG_BOOTDELAY	3
 #define CONFIG_BOOTFILE		"uImage"
-#define CONFIG_BOOTARGS		"console=ttyS0" __stringify(CONFIG_BAUDRATE)
+#define CONFIG_BOOTARGS		"console=ttyS0," __stringify(CONFIG_BAUDRATE)
 #define CONFIG_BOOTCOMMAND	"run mmcload; run mmcboot"
 #define CONFIG_LOADADDR		0x01000000
 #define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
diff --git a/include/configs/socfpga_vining_fpga.h b/include/configs/socfpga_vining_fpga.h
new file mode 100644
index 00000000000..1ccde1a76fe
--- /dev/null
+++ b/include/configs/socfpga_vining_fpga.h
@@ -0,0 +1,231 @@
+/*
+ * Copyright (C) 2015 Marek Vasut <marex@denx.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+#ifndef __CONFIG_SAMTEC_VINING_FPGA_H__
+#define __CONFIG_SAMTEC_VINING_FPGA_H__
+
+#include <asm/arch/base_addr_ac5.h>
+
+/* U-Boot Commands */
+#define CONFIG_SYS_NO_FLASH
+#define CONFIG_DOS_PARTITION
+#define CONFIG_FAT_WRITE
+#define CONFIG_HW_WATCHDOG
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_LED
+
+/* Memory configurations */
+#define PHYS_SDRAM_1_SIZE		0x40000000	/* 1GiB on VINING_FPGA */
+
+/* Booting Linux */
+#define CONFIG_BOOTDELAY	5
+#define CONFIG_BOOTFILE		"openwrt-socfpga-socfpga_cyclone5_vining_fpga-fit-uImage.itb"
+#define CONFIG_BOOTARGS		"console=ttyS0," __stringify(CONFIG_BAUDRATE)
+#define CONFIG_BOOTCOMMAND	"run selboot"
+#define CONFIG_LOADADDR		0x01000000
+#define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
+
+/* I2C EEPROM */
+#ifdef CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
+#define CONFIG_SYS_I2C_EEPROM_BUS		0
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70
+#endif
+
+/*
+ * Status LEDs:
+ *   0 ... Top Green
+ *   1 ... Top Red
+ *   2 ... Bottom Green
+ *   3 ... Bottom Red
+ */
+#define CONFIG_STATUS_LED
+#define CONFIG_GPIO_LED
+#define CONFIG_BOARD_SPECIFIC_LED
+#define STATUS_LED_BIT		48
+#define STATUS_LED_STATE	STATUS_LED_OFF
+#define STATUS_LED_PERIOD	(CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT1		53
+#define STATUS_LED_STATE1	STATUS_LED_OFF
+#define STATUS_LED_PERIOD1	(CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT2		54
+#define STATUS_LED_STATE2	STATUS_LED_OFF
+#define STATUS_LED_PERIOD2	(CONFIG_SYS_HZ / 2)
+#define STATUS_LED_BIT3		65
+#define STATUS_LED_STATE3	STATUS_LED_OFF
+#define STATUS_LED_PERIOD3	(CONFIG_SYS_HZ / 2)
+
+/* Ethernet on SoC (EMAC) */
+#if defined(CONFIG_CMD_NET)
+#define CONFIG_BOOTP_SEND_HOSTNAME
+/* PHY */
+#define CONFIG_PHY_MICREL
+#define CONFIG_PHY_MICREL_KSZ9021
+#endif
+
+/* Extra Environment */
+#define CONFIG_HOSTNAME			socfpga_vining_fpga
+
+/*
+ * Active LOW GPIO buttons:
+ * A: GPIO 77 ... the button between USB B and ethernet
+ * B: GPIO 78 ... the button between USB A ports
+ *
+ * The logic:
+ *  if button B is not pressed, boot normal Linux system immediatelly
+ *  if button B is pressed, wait $bootdelay and boot recovery system
+ */
+#define CONFIG_PREBOOT						\
+	"setenv hostname vining-${unit_serial} ; "		\
+	"setenv PS1 \"${unit_ident} (${unit_serial}) => \" ; "	\
+	"if gpio input 78 ; then "			\
+		"setenv bootdelay 10 ; "		\
+		"setenv boottype rcvr ; "		\
+	"else "						\
+		"setenv bootdelay 5 ; "			\
+		"setenv boottype norm ; "		\
+	"fi"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"verify=n\0" \
+	"consdev=ttyS0\0"						\
+	"baudrate=115200\0"						\
+	"bootscript=boot.scr\0"						\
+	"ubimtdnr=5\0"							\
+	"ubimtd=rootfs\0"						\
+	"ubipart=ubi0:rootfs\0"						\
+	"ubisfcs=1\0"		/* Default is flash at CS#1 */		\
+	"netdev=eth0\0"							\
+	"hostname=vining_fpga\0"						\
+	"kernel_addr_r=0x10000000\0"					\
+	"mtdparts_0=ff705000.spi.0:"					\
+		"1m(u-boot),"						\
+		"64k(env1),"						\
+		"64k(env2),"						\
+		"256k(samtec1),"					\
+		"256k(samtec2),"					\
+		"-(rcvrfs)\0"	/* Recovery */				\
+	"mtdparts_1=ff705000.spi.1:"					\
+		"32m(rootfs),"						\
+		"-(userfs)\0"						\
+	"update_filename=u-boot-with-spl-dtb.sfp\0"			\
+	"update_qspi_offset=0x0\0"					\
+	"update_qspi="		/* Update the QSPI firmware */		\
+		"if sf probe ; then "					\
+		"if tftp ${update_filename} ; then "			\
+		"sf update ${loadaddr} ${update_qspi_offset} ${filesize} ; " \
+		"fi ; "							\
+		"fi\0"							\
+	"fpga_filename=output_file.rbf\0"				\
+	"load_fpga="		/* Load FPGA bitstream */		\
+		"if tftp ${fpga_filename} ; then "			\
+		"fpga load 0 $loadaddr $filesize ; "			\
+		"bridge enable ; "					\
+		"fi\0"							\
+	"addcons="							\
+		"setenv bootargs ${bootargs} "				\
+		"console=${consdev},${baudrate}\0"			\
+	"addip="							\
+		"setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:"		\
+			"${netmask}:${hostname}:${netdev}:off\0"	\
+	"addmisc="							\
+		"setenv bootargs ${bootargs} ${miscargs}\0"		\
+	"addmtd="							\
+		"setenv mtdparts \"${mtdparts_0};${mtdparts_1}\" ; "	\
+		"setenv bootargs ${bootargs} mtdparts=${mtdparts}\0"	\
+	"addargs=run addcons addmtd addmisc\0"				\
+	"ubiload="							\
+		"ubi part ${ubimtd} ; ubifsmount ${ubipart} ; "		\
+		"ubifsload ${kernel_addr_r} /boot/${bootfile}\0"	\
+	"netload="							\
+		"tftp ${kernel_addr_r} ${hostname}/${bootfile}\0"	\
+	"miscargs=nohlt panic=1\0"					\
+	"ubiargs="							\
+		"setenv bootargs ubi.mtd=${ubimtdnr} "			\
+		"root=${ubipart} rootfstype=ubifs\0"			\
+	"nfsargs="							\
+		"setenv bootargs root=/dev/nfs rw "			\
+			"nfsroot=${serverip}:${rootpath},v3,tcp\0"	\
+	"ubi_sfsel="							\
+		"if test \"${boottype}\" = \"rcvr\" ; then "		\
+			"setenv ubisfcs 0 ; "				\
+			"setenv ubimtd rcvrfs ; "			\
+			"setenv ubimtdnr 5 ; "				\
+			"setenv mtdparts mtdparts=${mtdparts_0} ; "	\
+			"setenv mtdids nor0=ff705000.spi.0 ; "		\
+			"setenv ubipart ubi0:rootfs ; "			\
+		"else "							\
+			"setenv ubisfcs 1 ; "				\
+			"setenv ubimtd rootfs ; "			\
+			"setenv ubimtdnr 6 ; "				\
+			"setenv mtdparts mtdparts=${mtdparts_1} ; "	\
+			"setenv mtdids nor0=ff705000.spi.1 ; "		\
+			"setenv ubipart ubi0:rootfs ; "			\
+		"fi ; "							\
+		"sf probe 0:${ubisfcs}\0"				\
+	"ubi_ubi="							\
+		"run ubi_sfsel ubiload ubiargs addargs ; "		\
+		"bootm ${kernel_addr_r}\0"				\
+	"ubi_nfs="							\
+		"run ubiload nfsargs addip addargs ; "			\
+		"bootm ${kernel_addr_r}\0"				\
+	"net_ubi="							\
+		"run netload ubiargs addargs ; "			\
+		"bootm ${kernel_addr_r}\0"				\
+	"net_nfs="							\
+		"run netload nfsargs addip addargs ; "			\
+		"bootm ${kernel_addr_r}\0"				\
+	"selboot="	/* Select from where to boot. */		\
+		"if test \"${bootmode}\" = \"qspi\" ; then "		\
+			"led all off ; "				\
+			"if test \"${boottype}\" = \"rcvr\" ; then "	\
+				"echo \"Booting recovery system\" ; "	\
+				"led 3 on ; "	/* Bottom RED */	\
+			"fi ; "						\
+			"led 1 on ; "		/* Top RED */		\
+			"run ubi_ubi ; "				\
+		"else echo \"Unsupported boot mode: \"${bootmode} ; "	\
+		"fi\0"							\
+
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_MTD_UBI_FASTMAP
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define MTDPARTS_DEFAULT			\
+	"mtdparts=ff705000.spi.0:"		\
+		"1m(u-boot),"			\
+		"64k(env1),"			\
+		"64k(env2),"			\
+		"256k(samtec1),"		\
+		"256k(samtec2),"		\
+		"-(rcvrfs);"	/* Recovery */	\
+
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
+#define CONFIG_ENV_SECT_SIZE		(64 * 1024)
+#define CONFIG_ENV_OFFSET		0x100000
+#define CONFIG_ENV_OFFSET_REDUND	\
+	(CONFIG_ENV_OFFSET + CONFIG_ENV_SECT_SIZE)
+
+#define CONFIG_MISC_INIT_R
+#define CONFIG_BOARD_LATE_INIT
+
+/* Enable DFU to SF and RAM */
+#define CONFIG_DFU_RAM
+#define CONFIG_DFU_SF
+
+/* Support changing the prompt string */
+#define CONFIG_CMDLINE_PS_SUPPORT
+
+/* The rest of the configuration is shared */
+#include <configs/socfpga_common.h>
+
+#endif	/* __CONFIG_SAMTEC_VINING_FPGA_H__ */