diff options
| -rw-r--r-- | board/phytec/pfla02/pfla02.c | 8 | ||||
| -rw-r--r-- | configs/pfla02_defconfig | 2 | ||||
| -rw-r--r-- | include/configs/pfla02.h | 4 |
3 files changed, 5 insertions, 9 deletions
diff --git a/board/phytec/pfla02/pfla02.c b/board/phytec/pfla02/pfla02.c index fed8f52e3e1..0a961cc8a5a 100644 --- a/board/phytec/pfla02/pfla02.c +++ b/board/phytec/pfla02/pfla02.c @@ -117,7 +117,7 @@ static iomux_v3_cfg_t const gpios_pads[] = { IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL)), }; -#ifdef CONFIG_CMD_NAND +#if defined(CONFIG_CMD_NAND) && !defined(CONFIG_SPL_BUILD) /* NAND */ static iomux_v3_cfg_t const nfc_pads[] = { IOMUX_PADS(PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NAND_PAD_CTRL)), @@ -274,7 +274,7 @@ static void setup_gpios(void) SETUP_IOMUX_PADS(gpios_pads); } -#ifdef CONFIG_CMD_NAND +#if defined(CONFIG_CMD_NAND) && !defined(CONFIG_SPL_BUILD) static void setup_gpmi_nand(void) { struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; @@ -361,7 +361,7 @@ int board_init(void) setup_gpios(); -#ifdef CONFIG_CMD_NAND +#if defined(CONFIG_CMD_NAND) && !defined(CONFIG_SPL_BUILD) setup_gpmi_nand(); #endif return 0; @@ -657,7 +657,7 @@ void board_init_f(ulong dummy) .refr = 7, /* 8 refresh commands per refresh cycle */ }; -#ifdef CONFIG_CMD_NAND +#if defined(CONFIG_CMD_NAND) && !defined(CONFIG_SPL_BUILD) /* Enable NAND */ setup_gpmi_nand(); #endif diff --git a/configs/pfla02_defconfig b/configs/pfla02_defconfig index 5e5bbb05bd5..52cebd9e22e 100644 --- a/configs/pfla02_defconfig +++ b/configs/pfla02_defconfig @@ -37,7 +37,7 @@ CONFIG_SPL_YMODEM_SUPPORT=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y -# CONFIG_CMD_NAND is not set +CONFIG_CMD_NAND_TRIMFFS=y CONFIG_CMD_SF=y CONFIG_CMD_CACHE=y CONFIG_CMD_EXT4_WRITE=y diff --git a/include/configs/pfla02.h b/include/configs/pfla02.h index d4a7de7df6a..4162a71ca66 100644 --- a/include/configs/pfla02.h +++ b/include/configs/pfla02.h @@ -41,15 +41,11 @@ #define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 0 */ #define CONFIG_SYS_I2C_SPEED 100000 -#ifndef CONFIG_SPL_BUILD -#define CONFIG_CMD_NAND /* Enable NAND support */ -#define CONFIG_CMD_NAND_TRIMFFS #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE 0x40000000 #define CONFIG_SYS_NAND_5_ADDR_CYCLE #define CONFIG_SYS_NAND_ONFI_DETECTION -#endif /* DMA stuff, needed for GPMI/MXS NAND support */ |