diff options
| -rw-r--r-- | arch/arm/cpu/armv7/keystone/ddr3.c | 244 | ||||
| -rw-r--r-- | arch/arm/include/asm/arch-keystone/ddr3.h | 6 | ||||
| -rw-r--r-- | arch/arm/include/asm/arch-keystone/hardware-k2hk.h | 4 | ||||
| -rw-r--r-- | arch/arm/include/asm/arch-keystone/hardware.h | 46 | ||||
| -rw-r--r-- | board/ti/ks2_evm/board.c | 3 | ||||
| -rw-r--r-- | board/ti/ks2_evm/ddr3_k2hk.c | 16 |
6 files changed, 319 insertions, 0 deletions
diff --git a/arch/arm/cpu/armv7/keystone/ddr3.c b/arch/arm/cpu/armv7/keystone/ddr3.c index 2eabec10f95..923906afb5b 100644 --- a/arch/arm/cpu/armv7/keystone/ddr3.c +++ b/arch/arm/cpu/armv7/keystone/ddr3.c @@ -9,9 +9,19 @@ #include <asm/io.h> #include <common.h> +#include <asm/arch/msmc.h> #include <asm/arch/ddr3.h> #include <asm/arch/psc_defs.h> +#include <asm/ti-common/ti-edma3.h> + +#define DDR3_EDMA_BLK_SIZE_SHIFT 10 +#define DDR3_EDMA_BLK_SIZE (1 << DDR3_EDMA_BLK_SIZE_SHIFT) +#define DDR3_EDMA_BCNT 0x8000 +#define DDR3_EDMA_CCNT 1 +#define DDR3_EDMA_XF_SIZE (DDR3_EDMA_BLK_SIZE * DDR3_EDMA_BCNT) +#define DDR3_EDMA_SLOT_NUM 1 + void ddr3_init_ddrphy(u32 base, struct ddr3_phy_config *phy_cfg) { unsigned int tmp; @@ -70,6 +80,240 @@ void ddr3_init_ddremif(u32 base, struct ddr3_emif_config *emif_cfg) __raw_writel(emif_cfg->sdrfc, base + KS2_DDR3_SDRFC_OFFSET); } +int ddr3_ecc_support_rmw(u32 base) +{ + u32 value = __raw_readl(base + KS2_DDR3_MIDR_OFFSET); + + /* Check the DDR3 controller ID reg if the controllers + supports ECC RMW or not */ + if (value == 0x40461C02) + return 1; + + return 0; +} + +static void ddr3_ecc_config(u32 base, u32 value) +{ + u32 data; + + __raw_writel(value, base + KS2_DDR3_ECC_CTRL_OFFSET); + udelay(100000); /* delay required to synchronize across clock domains */ + + if (value & KS2_DDR3_ECC_EN) { + /* Clear the 1-bit error count */ + data = __raw_readl(base + KS2_DDR3_ONE_BIT_ECC_ERR_CNT_OFFSET); + __raw_writel(data, base + KS2_DDR3_ONE_BIT_ECC_ERR_CNT_OFFSET); + + /* enable the ECC interrupt */ + __raw_writel(KS2_DDR3_1B_ECC_ERR_SYS | KS2_DDR3_2B_ECC_ERR_SYS | + KS2_DDR3_WR_ECC_ERR_SYS, + base + KS2_DDR3_ECC_INT_ENABLE_SET_SYS_OFFSET); + + /* Clear the ECC error interrupt status */ + __raw_writel(KS2_DDR3_1B_ECC_ERR_SYS | KS2_DDR3_2B_ECC_ERR_SYS | + KS2_DDR3_WR_ECC_ERR_SYS, + base + KS2_DDR3_ECC_INT_STATUS_OFFSET); + } +} + +static void ddr3_reset_data(u32 base, u32 ddr3_size) +{ + u32 mpax[2]; + u32 seg_num; + u32 seg, blks, dst, edma_blks; + struct edma3_slot_config slot; + struct edma3_channel_config edma_channel; + u32 edma_src[DDR3_EDMA_BLK_SIZE/4] __aligned(16) = {0, }; + + /* Setup an edma to copy the 1k block to the entire DDR */ + puts("\nClear entire DDR3 memory to enable ECC\n"); + + /* save the SES MPAX regs */ + msmc_get_ses_mpax(8, 0, mpax); + + /* setup edma slot 1 configuration */ + slot.opt = EDMA3_SLOPT_TRANS_COMP_INT_ENB | + EDMA3_SLOPT_COMP_CODE(0) | + EDMA3_SLOPT_STATIC | EDMA3_SLOPT_AB_SYNC; + slot.bcnt = DDR3_EDMA_BCNT; + slot.acnt = DDR3_EDMA_BLK_SIZE; + slot.ccnt = DDR3_EDMA_CCNT; + slot.src_bidx = 0; + slot.dst_bidx = DDR3_EDMA_BLK_SIZE; + slot.src_cidx = 0; + slot.dst_cidx = 0; + slot.link = EDMA3_PARSET_NULL_LINK; + slot.bcntrld = 0; + edma3_slot_configure(KS2_EDMA0_BASE, DDR3_EDMA_SLOT_NUM, &slot); + + /* configure quik edma channel */ + edma_channel.slot = DDR3_EDMA_SLOT_NUM; + edma_channel.chnum = 0; + edma_channel.complete_code = 0; + /* event trigger after dst update */ + edma_channel.trigger_slot_word = EDMA3_TWORD(dst); + qedma3_start(KS2_EDMA0_BASE, &edma_channel); + + /* DDR3 size in segments (4KB seg size) */ + seg_num = ddr3_size << (30 - KS2_MSMC_SEG_SIZE_SHIFT); + + for (seg = 0; seg < seg_num; seg += KS2_MSMC_MAP_SEG_NUM) { + /* map 2GB 36-bit DDR address to 32-bit DDR address in EMIF + access slave interface so that edma driver can access */ + msmc_map_ses_segment(8, 0, base >> KS2_MSMC_SEG_SIZE_SHIFT, + KS2_MSMC_DST_SEG_BASE + seg, MPAX_SEG_2G); + + if ((seg_num - seg) > KS2_MSMC_MAP_SEG_NUM) + edma_blks = KS2_MSMC_MAP_SEG_NUM << + (KS2_MSMC_SEG_SIZE_SHIFT + - DDR3_EDMA_BLK_SIZE_SHIFT); + else + edma_blks = (seg_num - seg) << (KS2_MSMC_SEG_SIZE_SHIFT + - DDR3_EDMA_BLK_SIZE_SHIFT); + + /* Use edma driver to scrub 2GB DDR memory */ + for (dst = base, blks = 0; blks < edma_blks; + blks += DDR3_EDMA_BCNT, dst += DDR3_EDMA_XF_SIZE) { + edma3_set_src_addr(KS2_EDMA0_BASE, + edma_channel.slot, (u32)edma_src); + edma3_set_dest_addr(KS2_EDMA0_BASE, + edma_channel.slot, (u32)dst); + + while (edma3_check_for_transfer(KS2_EDMA0_BASE, + &edma_channel)) + udelay(10); + } + } + + qedma3_stop(KS2_EDMA0_BASE, &edma_channel); + + /* restore the SES MPAX regs */ + msmc_set_ses_mpax(8, 0, mpax); +} + +static void ddr3_ecc_init_range(u32 base) +{ + u32 ecc_val = KS2_DDR3_ECC_EN; + u32 rmw = ddr3_ecc_support_rmw(base); + + if (rmw) + ecc_val |= KS2_DDR3_ECC_RMW_EN; + + __raw_writel(0, base + KS2_DDR3_ECC_ADDR_RANGE1_OFFSET); + + ddr3_ecc_config(base, ecc_val); +} + +void ddr3_enable_ecc(u32 base, int test) +{ + u32 ecc_val = KS2_DDR3_ECC_ENABLE; + u32 rmw = ddr3_ecc_support_rmw(base); + + if (test) + ecc_val |= KS2_DDR3_ECC_ADDR_RNG_1_EN; + + if (!rmw) { + if (!test) + /* by default, disable ecc when rmw = 0 and no + ecc test */ + ecc_val = 0; + } else { + ecc_val |= KS2_DDR3_ECC_RMW_EN; + } + + ddr3_ecc_config(base, ecc_val); +} + +void ddr3_disable_ecc(u32 base) +{ + ddr3_ecc_config(base, 0); +} + +#if defined(CONFIG_SOC_K2HK) || defined(CONFIG_SOC_K2L) +static void cic_init(u32 base) +{ + /* Disable CIC global interrupts */ + __raw_writel(0, base + KS2_CIC_GLOBAL_ENABLE); + + /* Set to normal mode, no nesting, no priority hold */ + __raw_writel(0, base + KS2_CIC_CTRL); + __raw_writel(0, base + KS2_CIC_HOST_CTRL); + + /* Enable CIC global interrupts */ + __raw_writel(1, base + KS2_CIC_GLOBAL_ENABLE); +} + +static void cic_map_cic_to_gic(u32 base, u32 chan_num, u32 irq_num) +{ + /* Map the system interrupt to a CIC channel */ + __raw_writeb(chan_num, base + KS2_CIC_CHAN_MAP(0) + irq_num); + + /* Enable CIC system interrupt */ + __raw_writel(irq_num, base + KS2_CIC_SYS_ENABLE_IDX_SET); + + /* Enable CIC Host interrupt */ + __raw_writel(chan_num, base + KS2_CIC_HOST_ENABLE_IDX_SET); +} + +static void ddr3_map_ecc_cic2_irq(u32 base) +{ + cic_init(base); + cic_map_cic_to_gic(base, KS2_CIC2_DDR3_ECC_CHAN_NUM, + KS2_CIC2_DDR3_ECC_IRQ_NUM); +} +#endif + +void ddr3_init_ecc(u32 base) +{ + u32 ddr3_size; + + if (!ddr3_ecc_support_rmw(base)) { + ddr3_disable_ecc(base); + return; + } + + ddr3_ecc_init_range(base); + ddr3_size = ddr3_get_size(); + ddr3_reset_data(CONFIG_SYS_SDRAM_BASE, ddr3_size); + + /* mapping DDR3 ECC system interrupt from CIC2 to GIC */ +#if defined(CONFIG_SOC_K2HK) || defined(CONFIG_SOC_K2L) + ddr3_map_ecc_cic2_irq(KS2_CIC2_BASE); +#endif + ddr3_enable_ecc(base, 0); +} + +void ddr3_check_ecc_int(u32 base) +{ + char *env; + int ecc_test = 0; + u32 value = __raw_readl(base + KS2_DDR3_ECC_INT_STATUS_OFFSET); + + env = getenv("ecc_test"); + if (env) + ecc_test = simple_strtol(env, NULL, 0); + + if (value & KS2_DDR3_WR_ECC_ERR_SYS) + puts("DDR3 ECC write error interrupted\n"); + + if (value & KS2_DDR3_2B_ECC_ERR_SYS) { + puts("DDR3 ECC 2-bit error interrupted\n"); + + if (!ecc_test) { + puts("Reseting the device ...\n"); + reset_cpu(0); + } + } + + value = __raw_readl(base + KS2_DDR3_ONE_BIT_ECC_ERR_CNT_OFFSET); + if (value) { + printf("1-bit ECC err count: 0x%x\n", value); + value = __raw_readl(base + + KS2_DDR3_ONE_BIT_ECC_ERR_ADDR_LOG_OFFSET); + printf("1-bit ECC err address log: 0x%x\n", value); + } +} + void ddr3_reset_ddrphy(void) { u32 tmp; diff --git a/arch/arm/include/asm/arch-keystone/ddr3.h b/arch/arm/include/asm/arch-keystone/ddr3.h index 6bf35d35436..b044d6f18ff 100644 --- a/arch/arm/include/asm/arch-keystone/ddr3.h +++ b/arch/arm/include/asm/arch-keystone/ddr3.h @@ -49,8 +49,14 @@ struct ddr3_emif_config { }; void ddr3_init(void); +int ddr3_get_size(void); void ddr3_reset_ddrphy(void); +void ddr3_init_ecc(u32 base); +void ddr3_disable_ecc(u32 base); +void ddr3_check_ecc_int(u32 base); +int ddr3_ecc_support_rmw(u32 base); void ddr3_err_reset_workaround(void); +void ddr3_enable_ecc(u32 base, int test); void ddr3_init_ddrphy(u32 base, struct ddr3_phy_config *phy_cfg); void ddr3_init_ddremif(u32 base, struct ddr3_emif_config *emif_cfg); diff --git a/arch/arm/include/asm/arch-keystone/hardware-k2hk.h b/arch/arm/include/asm/arch-keystone/hardware-k2hk.h index 28de3f50107..5a9ea4fbca5 100644 --- a/arch/arm/include/asm/arch-keystone/hardware-k2hk.h +++ b/arch/arm/include/asm/arch-keystone/hardware-k2hk.h @@ -79,6 +79,10 @@ #define KS2_DDR3B_EMIF_DATA_BASE 0x60000000 #define KS2_DDR3B_DDRPHYC 0x02328000 +#define KS2_CIC2_DDR3_ECC_IRQ_NUM 0x0D3 /* DDR3 ECC system irq number */ +#define KS2_CIC2_DDR3_ECC_CHAN_NUM 0x01D /* DDR3 ECC int mapped to CIC2 + channel 29 */ + /* SGMII SerDes */ #define KS2_LANES_PER_SGMII_SERDES 4 diff --git a/arch/arm/include/asm/arch-keystone/hardware.h b/arch/arm/include/asm/arch-keystone/hardware.h index 8e0b8798b8c..c6a54d8b91b 100644 --- a/arch/arm/include/asm/arch-keystone/hardware.h +++ b/arch/arm/include/asm/arch-keystone/hardware.h @@ -87,6 +87,52 @@ typedef volatile unsigned int *dv_reg_p; #define KS2_DDR3_PLLCTRL_PHY_RESET 0x80000000 +/* DDR3 ECC */ +#define KS2_DDR3_ECC_INT_STATUS_OFFSET 0x0AC +#define KS2_DDR3_ECC_INT_ENABLE_SET_SYS_OFFSET 0x0B4 +#define KS2_DDR3_ECC_CTRL_OFFSET 0x110 +#define KS2_DDR3_ECC_ADDR_RANGE1_OFFSET 0x114 +#define KS2_DDR3_ONE_BIT_ECC_ERR_CNT_OFFSET 0x130 +#define KS2_DDR3_ONE_BIT_ECC_ERR_ADDR_LOG_OFFSET 0x13C + +/* DDR3 ECC Interrupt Status register */ +#define KS2_DDR3_1B_ECC_ERR_SYS BIT(5) +#define KS2_DDR3_2B_ECC_ERR_SYS BIT(4) +#define KS2_DDR3_WR_ECC_ERR_SYS BIT(3) + +/* DDR3 ECC Control register */ +#define KS2_DDR3_ECC_EN BIT(31) +#define KS2_DDR3_ECC_ADDR_RNG_PROT BIT(30) +#define KS2_DDR3_ECC_VERIFY_EN BIT(29) +#define KS2_DDR3_ECC_RMW_EN BIT(28) +#define KS2_DDR3_ECC_ADDR_RNG_1_EN BIT(0) + +#define KS2_DDR3_ECC_ENABLE (KS2_DDR3_ECC_EN | \ + KS2_DDR3_ECC_ADDR_RNG_PROT | \ + KS2_DDR3_ECC_VERIFY_EN) + +/* EDMA */ +#define KS2_EDMA0_BASE 0x02700000 + +/* EDMA3 register offsets */ +#define KS2_EDMA_QCHMAP0 0x0200 +#define KS2_EDMA_IPR 0x1068 +#define KS2_EDMA_ICR 0x1070 +#define KS2_EDMA_QEECR 0x1088 +#define KS2_EDMA_QEESR 0x108c +#define KS2_EDMA_PARAM_1(x) (0x4020 + (4 * x)) + +/* Chip Interrupt Controller */ +#define KS2_CIC2_BASE 0x02608000 + +/* Chip Interrupt Controller register offsets */ +#define KS2_CIC_CTRL 0x04 +#define KS2_CIC_HOST_CTRL 0x0C +#define KS2_CIC_GLOBAL_ENABLE 0x10 +#define KS2_CIC_SYS_ENABLE_IDX_SET 0x28 +#define KS2_CIC_HOST_ENABLE_IDX_SET 0x34 +#define KS2_CIC_CHAN_MAP(n) (0x0400 + (n << 2)) + #define KS2_UART0_BASE 0x02530c00 #define KS2_UART1_BASE 0x02531000 diff --git a/board/ti/ks2_evm/board.c b/board/ti/ks2_evm/board.c index 89917860638..40294934525 100644 --- a/board/ti/ks2_evm/board.c +++ b/board/ti/ks2_evm/board.c @@ -40,6 +40,7 @@ int dram_init(void) gd->ram_size = get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, CONFIG_MAX_RAM_BANK_SIZE); aemif_init(ARRAY_SIZE(aemif_configs), aemif_configs); + ddr3_init_ecc(KS2_DDR3A_EMIF_CTRL_BASE); return 0; } @@ -254,5 +255,7 @@ void ft_board_setup_ex(void *blob, bd_t *bd) reserve_start += 2; } } + + ddr3_check_ecc_int(KS2_DDR3A_EMIF_CTRL_BASE); } #endif diff --git a/board/ti/ks2_evm/ddr3_k2hk.c b/board/ti/ks2_evm/ddr3_k2hk.c index 6070a997702..a1c3d05f8e5 100644 --- a/board/ti/ks2_evm/ddr3_k2hk.c +++ b/board/ti/ks2_evm/ddr3_k2hk.c @@ -12,6 +12,8 @@ #include <asm/arch/ddr3.h> #include <asm/arch/hardware.h> +static int ddr3_size; + struct pll_init_data ddr3a_333 = DDR3_PLL_333(A); struct pll_init_data ddr3a_400 = DDR3_PLL_400(A); @@ -44,12 +46,14 @@ void ddr3_init(void) ddr3_init_ddremif(KS2_DDR3A_EMIF_CTRL_BASE, &ddr3_1600_8g); printf("DRAM: Capacity 8 GiB (includes reported below)\n"); + ddr3_size = 8; } else { ddr3_init_ddrphy(KS2_DDR3A_DDRPHYC, &ddr3phy_1600_8g); ddr3_1600_8g.sdcfg |= 0x1000; ddr3_init_ddremif(KS2_DDR3A_EMIF_CTRL_BASE, &ddr3_1600_8g); printf("DRAM: Capacity 4 GiB (includes reported below)\n"); + ddr3_size = 4; } } else if (!strcmp(dimm_name, "SQR-SD3T-2G1333SED")) { init_pll(&ddr3a_333); @@ -70,11 +74,15 @@ void ddr3_init(void) } ddr3_init_ddremif(KS2_DDR3A_EMIF_CTRL_BASE, &ddr3_1333_2g); + ddr3_size = 2; + printf("DRAM: 2 GiB"); } else { ddr3_init_ddrphy(KS2_DDR3A_DDRPHYC, &ddr3phy_1333_2g); ddr3_1333_2g.sdcfg |= 0x1000; ddr3_init_ddremif(KS2_DDR3A_EMIF_CTRL_BASE, &ddr3_1333_2g); + ddr3_size = 1; + printf("DRAM: 1 GiB"); } } else { printf("Unknown SO-DIMM. Cannot configure DDR3\n"); @@ -86,3 +94,11 @@ void ddr3_init(void) if (cpu_revision() <= 1) ddr3_err_reset_workaround(); } + +/** + * ddr3_get_size - return ddr3 size in GiB + */ +int ddr3_get_size(void) +{ + return ddr3_size; +} |