aboutsummaryrefslogtreecommitdiff
diff options
context:
space:
mode:
Diffstat
-rw-r--r--board/amcc/makalu/init.S10
-rw-r--r--board/amcc/makalu/makalu.c57
-rw-r--r--include/configs/makalu.h78
3 files changed, 62 insertions, 83 deletions
diff --git a/board/amcc/makalu/init.S b/board/amcc/makalu/init.S
index 806f5fdee2e..57c1774e028 100644
--- a/board/amcc/makalu/init.S
+++ b/board/amcc/makalu/init.S
@@ -54,14 +54,8 @@ ext_bus_cntlr_init:
/* base=00000000, size=128MByte (5), mode=2 (n*10*4) */
mtsdram_as(SDRAM_MB0CF, 0x00005201);
- /* SET SDRAM_MB1CF - Not enabled */
- mtsdram_as(SDRAM_MB1CF, 0x00000000);
-
- /* SET SDRAM_MB2CF - Not enabled */
- mtsdram_as(SDRAM_MB2CF, 0x00000000);
-
- /* SET SDRAM_MB3CF - Not enabled */
- mtsdram_as(SDRAM_MB3CF, 0x00000000);
+ /* base=08000000, size=128MByte (5), mode=2 (n*10*4) */
+ mtsdram_as(SDRAM_MB1CF, (0x08000000 >> 3) | 0x5201);
/* SDRAM_CLKTR: Adv Addr clock by 90 deg */
mtsdram_as(SDRAM_CLKTR,0x80000000);
diff --git a/board/amcc/makalu/makalu.c b/board/amcc/makalu/makalu.c
index 3b4a9c15477..b7933a056d1 100644
--- a/board/amcc/makalu/makalu.c
+++ b/board/amcc/makalu/makalu.c
@@ -26,7 +26,8 @@
#include <ppc405.h>
#include <libfdt.h>
#include <asm/processor.h>
-#include <asm-ppc/io.h>
+#include <asm/gpio.h>
+#include <asm/io.h>
#if defined(CONFIG_PCI)
#include <pci.h>
@@ -189,6 +190,11 @@ int board_early_init_f (void)
*/
mtsdr(SDR0_SRST, 0);
+ /* Reset PCIe slots */
+ gpio_write_bit(CFG_GPIO_PCIE_RST, 0);
+ udelay(100);
+ gpio_write_bit(CFG_GPIO_PCIE_RST, 1);
+
return 0;
}
@@ -239,45 +245,6 @@ int pci_pre_init(struct pci_controller * hose )
}
#endif /* defined(CONFIG_PCI) */
-/*************************************************************************
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- *
- ************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller * hose )
-{
- /*-------------------------------------------------------------------+
- * Disable everything
- *-------------------------------------------------------------------*/
- out32r( PCIX0_PIM0SA, 0 ); /* disable */
- out32r( PCIX0_PIM1SA, 0 ); /* disable */
- out32r( PCIX0_PIM2SA, 0 ); /* disable */
- out32r( PCIX0_EROMBA, 0 ); /* disable expansion rom */
-
- /*-------------------------------------------------------------------+
- * Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
- * strapping options to not support sizes such as 128/256 MB.
- *-------------------------------------------------------------------*/
- out32r( PCIX0_PIM0LAL, CFG_SDRAM_BASE );
- out32r( PCIX0_PIM0LAH, 0 );
- out32r( PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1 );
-
- out32r( PCIX0_BAR0, 0 );
-
- /*-------------------------------------------------------------------+
- * Program the board's subsystem id/vendor id
- *-------------------------------------------------------------------*/
- out16r( PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID );
- out16r( PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID );
-
- out16r( PCIX0_CMD, in16r(PCIX0_CMD) | PCI_COMMAND_MEMORY );
-}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
-
#ifdef CONFIG_PCI
static struct pci_controller pcie_hose[2] = {{0},{0}};
@@ -292,15 +259,13 @@ void pcie_setup_hoses(int busno)
for (i = 0; i < 2; i++) {
- if (is_end_point(i)) {
- printf("PCIE%d: will be configured as endpoint\n", i);
+ if (is_end_point(i))
ret = ppc4xx_init_pcie_endport(i);
- } else {
- printf("PCIE%d: will be configured as root-complex\n", i);
+ else
ret = ppc4xx_init_pcie_rootport(i);
- }
if (ret) {
- printf("PCIE%d: initialization failed\n", i);
+ printf("PCIE%d: initialization as %s failed\n", i,
+ is_end_point(i) ? "endpoint" : "root-complex");
continue;
}
diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index 30707799f5c..aa421c1392a 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -44,11 +44,11 @@
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0xFE000000
+#define CFG_FLASH_BASE 0xFC000000
#define CFG_FPGA_BASE 0xF0000000
#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
#define CFG_MONITOR_BASE (TEXT_BASE)
/*-----------------------------------------------------------------------
@@ -113,7 +113,7 @@
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
-#define CFG_MBYTES_SDRAM 128
+#define CFG_MBYTES_SDRAM 256
/*-----------------------------------------------------------------------
* I2C
@@ -150,7 +150,7 @@
#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
-#define CONFIG_PHY1_ADDR 2
+#define CONFIG_PHY1_ADDR 0
#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
@@ -187,8 +187,8 @@
"bootfile=makalu/uImage\0" \
"fdt_file=makalu/makalu.dtb\0" \
"fdt_addr=400000\0" \
- "kernel_addr=fe000000\0" \
- "ramdisk_addr=fe200000\0" \
+ "kernel_addr=fc000000\0" \
+ "ramdisk_addr=fc200000\0" \
"initrd_high=30000000\0" \
"load=tftp 200000 makalu/u-boot.bin\0" \
"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
@@ -282,6 +282,7 @@
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
/*-----------------------------------------------------------------------
* PCI stuff
@@ -323,7 +324,7 @@
*----------------------------------------------------------------------*/
/* Memory Bank 0 (NOR-FLASH) initialization */
#define CFG_EBC_PB0AP 0x04011000
-#define CFG_EBC_PB0CR 0xFE0BA000 /* BAS=0xFE0,BS=32MB,BU=R/W,BW=16bit*/
+#define CFG_EBC_PB0CR (CFG_FLASH_BASE | 0xda000)
/* Memory Bank 2 (CPLD) initialization */
#define CFG_EBC_PB2AP 0x9400C800
@@ -334,28 +335,47 @@
/*-----------------------------------------------------------------------
* GPIO Setup
*----------------------------------------------------------------------*/
-/*-----------------------------------------------------------------------
- * Definitions for GPIO setup (PPC405EX specific)
- *
- * GPIO0[0-3] - EBC data 0-3 inputs/outputs
- * GPIO0[4-7] - USB data 4-7 inputs/outputs
- * GPIO0[8-11] - NFCE# 1-3 inputs/outputs, GPIO11: IRQ6 inputs
- * GPIO0[12-15] - USB data 0-3 inputs/outputs
- * GPIO0[16-21] - UART0 control signal inputs/outputs
- *
- * GPIO0[22-25,27] - EBC control signal inputs/outputs
- * GPIO0[26] - Instruction trace outputs
- * GPIO0[28] - Float, N/C
- * GPIO0[29-31] - DMA control signal inputs/outputs
- */
-#define CFG_GPIO0_OSRL 0x00AA54AA
-#define CFG_GPIO0_OSRH 0x55500000
-#define CFG_GPIO0_TSRL 0x00AA54AA
-#define CFG_GPIO0_TSRH 0x55500000
-#define CFG_GPIO0_ISR1L 0x00005400
-#define CFG_GPIO0_ISR1H 0x55500000
-#define CFG_GPIO0_ISR2L 0x00550055
-#define CFG_GPIO0_ISR2H 0x00000000
+#define CFG_4xx_GPIO_TABLE { /* Out GPIO Alternate1 Alternate2 Alternate3 */ \
+{ \
+/* GPIO Core 0 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO0 EBC_DATA_PAR(0) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO1 EBC_DATA_PAR(1) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO2 EBC_DATA_PAR(2) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO3 EBC_DATA_PAR(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO4 EBC_DATA(20) USB2_DATA(4) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO5 EBC_DATA(21) USB2_DATA(5) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO6 EBC_DATA(22) USB2_DATA(6) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO7 EBC_DATA(23) USB2_DATA(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO8 EBC_CS(1) NFCE(1) IRQ(7) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO9 EBC_CS(2) NFCE(2) IRQ(8) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO10 EBC_CS(3) NFCE(3) IRQ(9) */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO11 IRQ(6) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO12 EBC_DATA(16) USB2_DATA(0) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_0}, /* GPIO13 EBC_DATA(17) USB2_DATA(1) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO14 EBC_DATA(18) USB2_DATA(2) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT2, GPIO_OUT_1}, /* GPIO15 EBC_DATA(19) USB2_DATA(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO16 UART0_DCD UART1_CTS */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO17 UART0_DSR UART1_RTS */ \
+{GPIO0_BASE, GPIO_IN, GPIO_ALT1, GPIO_OUT_0}, /* GPIO18 UART0_CTS */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO19 UART0_RTS */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO20 UART0_DTR UART1_TX */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO21 UART0_RI UART1_RX */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO22 EBC_HOLD_REQ DMA_ACK2 */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_SEL, GPIO_OUT_0}, /* GPIO23 EBC_HOLD_ACK DMA_REQ2 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO24 EBC_EXT_REQ DMA_EOT2 IRQ(4) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL, GPIO_OUT_0}, /* GPIO25 EBC_EXT_ACK DMA_ACK3 IRQ(3) */ \
+{GPIO0_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_0}, /* GPIO26 EBC_ADDR(5) DMA_EOT0 TS(3) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO27 EBC_BUS_REQ DMA_EOT3 IRQ(5) */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO28 */ \
+{GPIO0_BASE, GPIO_IN, GPIO_SEL , GPIO_OUT_0}, /* GPIO29 IRQ(2) DMA_EOT1 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO30 IRQ(1) DMA_REQ1 */ \
+{GPIO0_BASE, GPIO_IN , GPIO_ALT1, GPIO_OUT_0}, /* GPIO31 IRQ(0) DMA_ACK1 */ \
+} \
+}
+
+#define CFG_GPIO_PCIE_RST 23
+#define CFG_GPIO_PCIE_CLKREQ 27
+#define CFG_GPIO_PCIE_WAKE 28
/*
* Internal Definitions
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-11 00:42:05 +0000