diff options
Diffstat (limited to 'arch/arm/mach-orion5x/cpu.c')
| -rw-r--r-- | arch/arm/mach-orion5x/cpu.c | 294 |
1 files changed, 294 insertions, 0 deletions
diff --git a/arch/arm/mach-orion5x/cpu.c b/arch/arm/mach-orion5x/cpu.c new file mode 100644 index 00000000000..f88db3b1f96 --- /dev/null +++ b/arch/arm/mach-orion5x/cpu.c @@ -0,0 +1,294 @@ +/* + * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net> + * + * Based on original Kirkwood support which is + * (C) Copyright 2009 + * Marvell Semiconductor <www.marvell.com> + * Written-by: Prafulla Wadaskar <prafulla@marvell.com> + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#include <common.h> +#include <netdev.h> +#include <asm/cache.h> +#include <asm/io.h> +#include <u-boot/md5.h> +#include <asm/arch/cpu.h> + +#define BUFLEN 16 + +void reset_cpu(unsigned long ignored) +{ + struct orion5x_cpu_registers *cpureg = + (struct orion5x_cpu_registers *)ORION5X_CPU_REG_BASE; + + writel(readl(&cpureg->rstoutn_mask) | (1 << 2), + &cpureg->rstoutn_mask); + writel(readl(&cpureg->sys_soft_rst) | 1, + &cpureg->sys_soft_rst); + while (1) + ; +} + +/* + * Compute Window Size field value from size expressed in bytes + * Used with the Base register to set the address window size and location. + * Must be programmed from LSB to MSB as sequence of ones followed by + * sequence of zeros. The number of ones specifies the size of the window in + * 64 KiB granularity (e.g., a value of 0x00FF specifies 256 = 16 MiB). + * NOTES: + * 1) A sizeval equal to 0x0 specifies 4 GiB. + * 2) A return value of 0x0 specifies 64 KiB. + */ +unsigned int orion5x_winctrl_calcsize(unsigned int sizeval) +{ + /* + * Calculate the number of 64 KiB blocks needed minus one (rounding up). + * For sizeval > 0 this is equivalent to: + * sizeval = (u32) ceil((double) sizeval / 65536.0) - 1 + */ + sizeval = (sizeval - 1) >> 16; + + /* + * Propagate 'one' bits to the right by 'oring' them. + * We need only treat bits 15-0. + */ + sizeval |= sizeval >> 1; /* 'Or' bit 15 onto bit 14 */ + sizeval |= sizeval >> 2; /* 'Or' bits 15-14 onto bits 13-12 */ + sizeval |= sizeval >> 4; /* 'Or' bits 15-12 onto bits 11-8 */ + sizeval |= sizeval >> 8; /* 'Or' bits 15-8 onto bits 7-0*/ + + return sizeval; +} + +/* + * orion5x_config_adr_windows - Configure address Windows + * + * There are 8 address windows supported by Orion5x Soc to addess different + * devices. Each window can be configured for size, BAR and remap addr + * Below configuration is standard for most of the cases + * + * If remap function not used, remap_lo must be set as base + * + * NOTES: + * + * 1) in order to avoid windows with inconsistent control and base values + * (which could prevent access to BOOTCS and hence execution from FLASH) + * always disable window before writing the base value then reenable it + * by writing the control value. + * + * 2) in order to avoid losing access to BOOTCS when disabling window 7, + * first configure window 6 for BOOTCS, then configure window 7 for BOOTCS, + * then configure windows 6 for its own target. + * + * Reference Documentation: + * Mbus-L to Mbus Bridge Registers Configuration. + * (Sec 25.1 and 25.3 of Datasheet) + */ +int orion5x_config_adr_windows(void) +{ + struct orion5x_win_registers *winregs = + (struct orion5x_win_registers *)ORION5X_CPU_WIN_BASE; + +/* Disable window 0, configure it for its intended target, enable it. */ + writel(0, &winregs[0].ctrl); + writel(ORION5X_ADR_PCIE_MEM, &winregs[0].base); + writel(ORION5X_ADR_PCIE_MEM_REMAP_LO, &winregs[0].remap_lo); + writel(ORION5X_ADR_PCIE_MEM_REMAP_HI, &winregs[0].remap_hi); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCIE_MEM, + ORION5X_TARGET_PCIE, ORION5X_ATTR_PCIE_MEM, + ORION5X_WIN_ENABLE), &winregs[0].ctrl); +/* Disable window 1, configure it for its intended target, enable it. */ + writel(0, &winregs[1].ctrl); + writel(ORION5X_ADR_PCIE_IO, &winregs[1].base); + writel(ORION5X_ADR_PCIE_IO_REMAP_LO, &winregs[1].remap_lo); + writel(ORION5X_ADR_PCIE_IO_REMAP_HI, &winregs[1].remap_hi); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCIE_IO, + ORION5X_TARGET_PCIE, ORION5X_ATTR_PCIE_IO, + ORION5X_WIN_ENABLE), &winregs[1].ctrl); +/* Disable window 2, configure it for its intended target, enable it. */ + writel(0, &winregs[2].ctrl); + writel(ORION5X_ADR_PCI_MEM, &winregs[2].base); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCI_MEM, + ORION5X_TARGET_PCI, ORION5X_ATTR_PCI_MEM, + ORION5X_WIN_ENABLE), &winregs[2].ctrl); +/* Disable window 3, configure it for its intended target, enable it. */ + writel(0, &winregs[3].ctrl); + writel(ORION5X_ADR_PCI_IO, &winregs[3].base); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_PCI_IO, + ORION5X_TARGET_PCI, ORION5X_ATTR_PCI_IO, + ORION5X_WIN_ENABLE), &winregs[3].ctrl); +/* Disable window 4, configure it for its intended target, enable it. */ + writel(0, &winregs[4].ctrl); + writel(ORION5X_ADR_DEV_CS0, &winregs[4].base); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS0, + ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS0, + ORION5X_WIN_ENABLE), &winregs[4].ctrl); +/* Disable window 5, configure it for its intended target, enable it. */ + writel(0, &winregs[5].ctrl); + writel(ORION5X_ADR_DEV_CS1, &winregs[5].base); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS1, + ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS1, + ORION5X_WIN_ENABLE), &winregs[5].ctrl); +/* Disable window 6, configure it for FLASH, enable it. */ + writel(0, &winregs[6].ctrl); + writel(ORION5X_ADR_BOOTROM, &winregs[6].base); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_BOOTROM, + ORION5X_TARGET_DEVICE, ORION5X_ATTR_BOOTROM, + ORION5X_WIN_ENABLE), &winregs[6].ctrl); +/* Disable window 7, configure it for FLASH, enable it. */ + writel(0, &winregs[7].ctrl); + writel(ORION5X_ADR_BOOTROM, &winregs[7].base); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_BOOTROM, + ORION5X_TARGET_DEVICE, ORION5X_ATTR_BOOTROM, + ORION5X_WIN_ENABLE), &winregs[7].ctrl); +/* Disable window 6, configure it for its intended target, enable it. */ + writel(0, &winregs[6].ctrl); + writel(ORION5X_ADR_DEV_CS2, &winregs[6].base); + writel(ORION5X_CPU_WIN_CTRL_DATA(ORION5X_SZ_DEV_CS2, + ORION5X_TARGET_DEVICE, ORION5X_ATTR_DEV_CS2, + ORION5X_WIN_ENABLE), &winregs[6].ctrl); + + return 0; +} + +/* + * Orion5x identification is done through PCIE space. + */ + +u32 orion5x_device_id(void) +{ + return readl(PCIE_DEV_ID_OFF) >> 16; +} + +u32 orion5x_device_rev(void) +{ + return readl(PCIE_DEV_REV_OFF) & 0xff; +} + +#if defined(CONFIG_DISPLAY_CPUINFO) + +/* Display device and revision IDs. + * This function must cover all known device/revision + * combinations, not only the one for which u-boot is + * compiled; this way, one can identify actual HW in + * case of a mismatch. + */ +int print_cpuinfo(void) +{ + char dev_str[7]; /* room enough for 0x0000 plus null byte */ + char rev_str[5]; /* room enough for 0x00 plus null byte */ + char *dev_name = NULL; + char *rev_name = NULL; + + u32 dev = orion5x_device_id(); + u32 rev = orion5x_device_rev(); + + if (dev == MV88F5181_DEV_ID) { + dev_name = "MV88F5181"; + if (rev == MV88F5181_REV_B1) + rev_name = "B1"; + else if (rev == MV88F5181L_REV_A1) { + dev_name = "MV88F5181L"; + rev_name = "A1"; + } else if (rev == MV88F5181L_REV_A0) { + dev_name = "MV88F5181L"; + rev_name = "A0"; + } + } else if (dev == MV88F5182_DEV_ID) { + dev_name = "MV88F5182"; + if (rev == MV88F5182_REV_A2) + rev_name = "A2"; + } else if (dev == MV88F5281_DEV_ID) { + dev_name = "MV88F5281"; + if (rev == MV88F5281_REV_D2) + rev_name = "D2"; + else if (rev == MV88F5281_REV_D1) + rev_name = "D1"; + else if (rev == MV88F5281_REV_D0) + rev_name = "D0"; + } else if (dev == MV88F6183_DEV_ID) { + dev_name = "MV88F6183"; + if (rev == MV88F6183_REV_B0) + rev_name = "B0"; + } + if (dev_name == NULL) { + sprintf(dev_str, "0x%04x", dev); + dev_name = dev_str; + } + if (rev_name == NULL) { + sprintf(rev_str, "0x%02x", rev); + rev_name = rev_str; + } + + printf("SoC: Orion5x %s-%s\n", dev_name, rev_name); + + return 0; +} +#endif /* CONFIG_DISPLAY_CPUINFO */ + +#ifdef CONFIG_ARCH_CPU_INIT +int arch_cpu_init(void) +{ + /* Enable and invalidate L2 cache in write through mode */ + invalidate_l2_cache(); + + orion5x_config_adr_windows(); + + return 0; +} +#endif /* CONFIG_ARCH_CPU_INIT */ + +/* + * SOC specific misc init + */ +#if defined(CONFIG_ARCH_MISC_INIT) +int arch_misc_init(void) +{ + u32 temp; + + /*CPU streaming & write allocate */ + temp = readfr_extra_feature_reg(); + temp &= ~(1 << 28); /* disable wr alloc */ + writefr_extra_feature_reg(temp); + + temp = readfr_extra_feature_reg(); + temp &= ~(1 << 29); /* streaming disabled */ + writefr_extra_feature_reg(temp); + + /* L2Cache settings */ + temp = readfr_extra_feature_reg(); + /* Disable L2C pre fetch - Set bit 24 */ + temp |= (1 << 24); + /* enable L2C - Set bit 22 */ + temp |= (1 << 22); + writefr_extra_feature_reg(temp); + + icache_enable(); + /* Change reset vector to address 0x0 */ + temp = get_cr(); + set_cr(temp & ~CR_V); + + /* Set CPIOs and MPPs - values provided by board + include file */ + writel(ORION5X_MPP0_7, ORION5X_MPP_BASE+0x00); + writel(ORION5X_MPP8_15, ORION5X_MPP_BASE+0x04); + writel(ORION5X_MPP16_23, ORION5X_MPP_BASE+0x50); + writel(ORION5X_GPIO_OUT_VALUE, ORION5X_GPIO_BASE+0x00); + writel(ORION5X_GPIO_OUT_ENABLE, ORION5X_GPIO_BASE+0x04); + writel(ORION5X_GPIO_IN_POLARITY, ORION5X_GPIO_BASE+0x0c); + + /* initialize timer */ + timer_init_r(); + return 0; +} +#endif /* CONFIG_ARCH_MISC_INIT */ + +#ifdef CONFIG_MVGBE +int cpu_eth_init(bd_t *bis) +{ + mvgbe_initialize(bis); + return 0; +} +#endif |