diff options
Diffstat (limited to 'board/amcc/ebony/README')
| -rw-r--r-- | board/amcc/ebony/README | 136 |
1 files changed, 0 insertions, 136 deletions
diff --git a/board/amcc/ebony/README b/board/amcc/ebony/README deleted file mode 100644 index 4df00b35612..00000000000 --- a/board/amcc/ebony/README +++ /dev/null @@ -1,136 +0,0 @@ - AMCC Ebony Board - - Last Update: September 12, 2002 -======================================================================= - -This file contains some handy info regarding U-Boot and the AMCC -Ebony evaluation board. See the README.ppc440 for additional -information. - - -SWITCH SETTINGS & JUMPERS -========================== - -Here's what I've been using successfully. If you feel inclined to -change things ... please read the docs! - -DIPSW U46 U80 ------------------------- -SW 1 off on -SW 2 on on -SW 3 on on -SW 4 off on -SW 5 on off -SW 6 on on -SW 7 on off -SW 8 on off - -J41: strapped -J42: open - -All others are factory default. - - -I2C probe -===================== - -The i2c utilities have been tested on both Rev B. and Rev C. and -look good. The CONFIG_SYS_I2C_NOPROBES macro is defined to prevent -probing the CDCV850 clock controller at address 0x69 (since reading -it causes the i2c implementation to misbehave. The output of -'i2c probe' should look like this (assuming you are only using a single -SO-DIMM: - -=> i2c probe -Valid chip addresses: 50 53 54 -Excluded chip addresses: 69 - - -GETTING OUT OF I2C TROUBLE -=========================== - -If you're like me ... you may have screwed up your bootstrap serial -eeprom ... or worse, your SPD eeprom when experimenting with the -i2c commands. If so, here are some ideas on how to get out of -trouble: - -Serial bootstrap eeprom corruption: ------------------------------------ -Power down the board and set the following straps: - -J41 - open -J42 - strapped - -This will select the default sys0 and sys1 settings (the serial -eeproms are not used). Then power up the board and fix the serial -eeprom using the 'i2c mm' command. Here are the values I currently -use: - -=> i2c md 50 0 10 -0000: bf a2 04 01 ae 94 11 00 00 00 00 00 00 00 00 00 ................ - -=> i2c md 54 0 10 -0000: 8f b3 24 01 4d 14 11 00 00 00 00 00 00 00 00 00 ..$.M........... - -Once you have the eeproms set correctly change the -J41/J42 straps as you desire. - -SPD eeprom corruption: ------------------------- -I've corrupted the SPD eeprom several times ... perhaps too much coffee -and not enough presence of mind ;-). By default, the ebony code uses -the SPD to initialize the DDR SDRAM control registers. So if the SPD -eeprom is corrupted, U-Boot will never get into ram. Here's how I got -out of this situation: - -0. First, _before_ playing with the i2c utilities, do an 'i2c probe', then -use 'i2c md' to capture the various device contents to a file. Some day -you may be glad you did this ... trust me :-). Otherwise try the -following: - -1. In the include/configs/EBONY.h file find the line that defines -the CONFIG_SPD_EEPROM macro and undefine it. E.g: - -#undef CONFIG_SPD_EEPROM - -This will make the code use default SDRAM control register -settings without using the SPD eeprom. - -2. Rebuild U-Boot - -3. Load the new U-Boot image and reboot ebony. - -4. Repair the SPD eeprom using the 'i2c mm' command. Here's the eeprom -contents that work with the default SO-DIMM that comes with the -ebony board (micron 8VDDT164AG-265A1). Note: these are probably -_not_ the factory settings ... but they work. - -=> i2c md 53 0 10 80 -0000: 80 08 07 0c 0a 01 40 00 04 75 75 00 80 08 00 01 ......@..uu..... -0010: 0e 04 0c 01 02 20 00 a0 75 00 00 50 3c 50 2d 20 ..... ..u..P<P- -0020: 90 90 50 50 00 00 00 00 00 41 4b 34 32 75 00 00 ..PP.....AK42u.. -0030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 9c ................ -0040: 2c 00 00 00 00 00 00 00 08 38 56 44 44 54 31 36 ,........8VDDT16 -0050: 36 34 41 47 2d 32 36 35 41 31 20 01 00 01 2c 63 64AG-265A1 ...,c -0060: 22 25 ab 00 00 00 00 00 00 00 00 00 00 00 00 00 "%.............. -0070: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ - - -PCI DOUBLE-ENUMERATION WOES -=========================== - -If you're not using PCI-X cards and are simply using 32-bit and/or -33 MHz cards via extenders and the like, you may notice that the -initial pci scan reports various devices twice ... and configuration -does not succeed (one or more devices are enumerated twice). To correct -this we replaced the 2K ohm resistor on the IDSEL line(s) with a -22 ohm resistor and the problem went away. This change hasn't broken -anything yet -- use at your own risk. - -We never tested anything other than 33 MHz/32-bit cards. If you have -the chance to do this, please let me know how things turn out :-) - - -Regards, ---Scott -<smcnutt@artesyncp.com> |