diff options
Diffstat (limited to 'doc/board/phytec/phycore-am64x.rst')
| -rw-r--r-- | doc/board/phytec/phycore-am64x.rst | 159 |
1 files changed, 159 insertions, 0 deletions
diff --git a/doc/board/phytec/phycore-am64x.rst b/doc/board/phytec/phycore-am64x.rst new file mode 100644 index 00000000000..a27ad01027b --- /dev/null +++ b/doc/board/phytec/phycore-am64x.rst @@ -0,0 +1,159 @@ +.. SPDX-License-Identifier: GPL-2.0+ +.. sectionauthor:: Wadim Egorov <w.egorov@phytec.de> + +phyCORE-AM64x +============= + +The `phyCORE-AM64x <https://www.phytec.com/product/phycore-am64x>`_ is a +SoM (System on Module) featuring TI's AM64x SoC. It can be used in combination +with different carrier boards. This module can come with different sizes and +models for DDR, eMMC, SPI NOR Flash and various SoCs from the AM64x family. + +A development Kit, called `phyBOARD-Lyra <https://www.phytec.com/product/phyboard-am64x>`_ +is used as a carrier board reference design around the AM64x SoM. + +Quickstart +---------- + +* Download sources and TI firmware blobs +* Build Trusted Firmware-A +* Build OP-TEE +* Build U-Boot for the R5 +* Build U-Boot for the A53 +* Create bootable uSD Card +* Boot + +Sources +------- + +.. include:: ../ti/k3.rst + :start-after: .. k3_rst_include_start_boot_sources + :end-before: .. k3_rst_include_end_boot_sources + +Build procedure +--------------- + +Setup the environment variables: + +.. include:: ../ti/k3.rst + :start-after: .. k3_rst_include_start_common_env_vars_desc + :end-before: .. k3_rst_include_end_common_env_vars_desc + +.. include:: ../ti/k3.rst + :start-after: .. k3_rst_include_start_board_env_vars_desc + :end-before: .. k3_rst_include_end_board_env_vars_desc + +Set the variables corresponding to this platform: + +.. include:: ../ti/k3.rst + :start-after: .. k3_rst_include_start_common_env_vars_defn + :end-before: .. k3_rst_include_end_common_env_vars_defn +.. code-block:: bash + + $ export UBOOT_CFG_CORTEXR=phycore_am64x_r5_defconfig + $ export UBOOT_CFG_CORTEXA=phycore_am64x_a53_defconfig + $ export TFA_BOARD=lite + $ # we don't use any extra TFA parameters + $ unset TFA_EXTRA_ARGS + $ export OPTEE_PLATFORM=k3-am64x + # we don't use any extra OPTEE parameters + unset OPTEE_EXTRA_ARGS + +.. include:: ../ti/am62x_sk.rst + :start-after: .. am62x_evm_rst_include_start_build_steps + :end-before: .. am62x_evm_rst_include_end_build_steps + +uSD Card creation +----------------- + +Use fdisk to partition the uSD card. The layout should look similar to: + +.. code-block:: bash + + $ sudo fdisk -l /dev/mmcblk0 + Disk /dev/mmcblk0: 7.56 GiB, 8120172544 bytes, 15859712 sectors + Units: sectors of 1 * 512 = 512 bytes + Sector size (logical/physical): 512 bytes / 512 bytes + I/O size (minimum/optimal): 512 bytes / 512 bytes + Disklabel type: dos + Disk identifier: 0x6583d9a3 + + Device Boot Start End Sectors Size Id Type + /dev/mmcblk0p1 * 2048 264191 262144 128M c W95 FAT32 (LBA) + /dev/mmcblk0p2 264192 1934953 1670762 815.8M 83 Linux + + +Once partitioned, the boot partition has to be formatted with a FAT filesystem. +Assuming the uSD card is `/dev/mmcblk0`: + +.. code-block:: bash + + $ mkfs.vfat /dev/mmcblk0p1 + +To boot from a micro SD card on a HSFS device simply copy the following +artifacts to the FAT partition: + +* tiboot3.bin from R5 build +* tispl.bin from Cortex-A build +* u-boot.img from Cortex-A build + +Boot +---- + +Put the uSD card in the slot on the board and apply power. Check the serial +console for output. + +Flash to SPI NOR +---------------- + +Below commands can be used to flash the SPI NOR flash; assuming +tiboot3.bin, tispl.bin and u-boot.img are stored on the uSD card. + +.. code-block:: bash + + sf probe + fatload mmc 1 ${loadaddr} tiboot3.bin + sf update $loadaddr 0x0 $filesize + fatload mmc 1 ${loadaddr} tispl.bin + sf update $loadaddr 0x80000 $filesize + fatload mmc 1 ${loadaddr} u-boot.img + sf update $loadaddr 0x280000 $filesize + + +Boot Modes +---------- + +The phyCORE-AM64x development kit supports booting from many different +interfaces. By default, the development kit is set to boot from the micro-SD +card. To change the boot device, DIP switches S5 and S6 can be used. +Boot switches should be changed with power off. + +.. list-table:: Boot Modes + :widths: 16 16 16 + :header-rows: 1 + + * - Switch Label + - SW3: 12345678 + - SW4: 12345678 + + * - uSD + - 11000010 + - 01000000 + + * - eMMC + - 11010010 + - 00000000 + + * - OSPI + - 11010000 + - 10000000 + + * - UART + - 11011100 + - 00000000 + +Further Information +------------------- + +Please see :doc:`../ti/am64x_evm` chapter for further AM64 SoC related documentation +and https://docs.phytec.com/phycore-am64x for vendor documentation. |