diff options
Diffstat (limited to 'drivers/ddr/marvell/axp/ddr3_axp_config.h')
| -rw-r--r-- | drivers/ddr/marvell/axp/ddr3_axp_config.h | 146 |
1 files changed, 146 insertions, 0 deletions
diff --git a/drivers/ddr/marvell/axp/ddr3_axp_config.h b/drivers/ddr/marvell/axp/ddr3_axp_config.h new file mode 100644 index 00000000000..800d2d14765 --- /dev/null +++ b/drivers/ddr/marvell/axp/ddr3_axp_config.h @@ -0,0 +1,146 @@ +/* + * Copyright (C) Marvell International Ltd. and its affiliates + * + * SPDX-License-Identifier: GPL-2.0 + */ + +#ifndef __DDR3_AXP_CONFIG_H +#define __DDR3_AXP_CONFIG_H + +/* + * DDR3_LOG_LEVEL Information + * + * Level 0: Provides an error code in a case of failure, RL, WL errors + * and other algorithm failure + * Level 1: Provides the D-Unit setup (SPD/Static configuration) + * Level 2: Provides the windows margin as a results of DQS centeralization + * Level 3: Provides the windows margin of each DQ as a results of DQS + * centeralization + */ +#ifdef CONFIG_DDR_LOG_LEVEL +#define DDR3_LOG_LEVEL CONFIG_DDR_LOG_LEVEL +#else +#define DDR3_LOG_LEVEL 0 +#endif + +#define DDR3_PBS 1 + +/* This flag allows the execution of SW WL/RL upon HW failure */ +#define DDR3_RUN_SW_WHEN_HW_FAIL 1 + +/* + * General Configurations + * + * The following parameters are required for proper setup: + * + * DDR_TARGET_FABRIC - Set desired fabric configuration + * (for sample@Reset fabfreq parameter) + * DRAM_ECC - Set ECC support 1/0 + * BUS_WIDTH - 64/32 bit + * CONFIG_SPD_EEPROM - Enables auto detection of DIMMs and their timing values + * DQS_CLK_ALIGNED - Set this if CLK and DQS signals are aligned on board + * MIXED_DIMM_STATIC - Mixed DIMM + On board devices support (ODT registers + * values are taken statically) + * DDR3_TRAINING_DEBUG - Debug prints of internal code + */ +#define DDR_TARGET_FABRIC 5 +#define DRAM_ECC 0 + +#ifdef MV_DDR_32BIT +#define BUS_WIDTH 32 +#else +#define BUS_WIDTH 64 +#endif + +#undef DQS_CLK_ALIGNED +#undef MIXED_DIMM_STATIC +#define DDR3_TRAINING_DEBUG 0 +#define REG_DIMM_SKIP_WL 0 + +/* Marvell boards specific configurations */ +#if defined(DB_78X60_PCAC) +#undef CONFIG_SPD_EEPROM +#define STATIC_TRAINING +#endif + +#if defined(DB_78X60_AMC) +#undef CONFIG_SPD_EEPROM +#undef DRAM_ECC +#define DRAM_ECC 1 +#endif + +#ifdef CONFIG_SPD_EEPROM +/* + * DIMM support parameters: + * DRAM_2T - Set Desired 2T Mode - 0 - 1T, 0x1 - 2T, 0x2 - 3T + * DIMM_CS_BITMAP - bitmap representing the optional CS in DIMMs + * (0xF=CS0+CS1+CS2+CS3, 0xC=CS2+CS3...) + */ +#define DRAM_2T 0x0 +#define DIMM_CS_BITMAP 0xF +#define DUNIT_SPD +#endif + +#ifdef DRAM_ECC +/* + * ECC support parameters: + * + * U_BOOT_START_ADDR, U_BOOT_SCRUB_SIZE - relevant when using ECC and need + * to configure the scrubbing area + */ +#define TRAINING_SIZE 0x20000 +#define U_BOOT_START_ADDR 0 +#define U_BOOT_SCRUB_SIZE 0x1000000 /* TRAINING_SIZE */ +#endif + +/* + * Registered DIMM Support - In case registered DIMM is attached, + * please supply the following values: + * (see JEDEC - JESD82-29A "Definition of the SSTE32882 Registering Clock + * Driver with Parity and Quad Chip + * Selects for DDR3/DDR3L/DDR3U RDIMM 1.5 V/1.35 V/1.25 V Applications") + * RC0: Global Features Control Word + * RC1: Clock Driver Enable Control Word + * RC2: Timing Control Word + * RC3-RC5 - taken from SPD + * RC8: Additional IBT Setting Control Word + * RC9: Power Saving Settings Control Word + * RC10: Encoding for RDIMM Operating Speed + * RC11: Operating Voltage VDD and VREFCA Control Word + */ +#define RDIMM_RC0 0 +#define RDIMM_RC1 0 +#define RDIMM_RC2 0 +#define RDIMM_RC8 0 +#define RDIMM_RC9 0 +#define RDIMM_RC10 0x2 +#define RDIMM_RC11 0x0 + +#if defined(MIXED_DIMM_STATIC) || !defined(CONFIG_SPD_EEPROM) +#define DUNIT_STATIC +#endif + +#if defined(MIXED_DIMM_STATIC) || defined(CONFIG_SPD_EEPROM) +/* + * This flag allows the user to change the dram refresh cycle in ps, + * only in case of SPD or MIX DIMM topology + */ +#define TREFI_USER_EN + +#ifdef TREFI_USER_EN +#define TREFI_USER 3900000 +#endif +#endif + +#ifdef CONFIG_SPD_EEPROM +/* + * AUTO_DETECTION_SUPPORT - relevant ONLY for Marvell DB boards. + * Enables I2C auto detection different options + */ +#if defined(CONFIG_DB_88F78X60) || defined(CONFIG_DB_88F78X60_REV2) || \ + defined(CONFIG_DB_784MP_GP) +#define AUTO_DETECTION_SUPPORT +#endif +#endif + +#endif /* __DDR3_AXP_CONFIG_H */ |