diff options
Diffstat (limited to 'dts/upstream/Bindings/mmc/marvell,xenon-sdhci.yaml')
| -rw-r--r-- | dts/upstream/Bindings/mmc/marvell,xenon-sdhci.yaml | 277 |
1 files changed, 277 insertions, 0 deletions
diff --git a/dts/upstream/Bindings/mmc/marvell,xenon-sdhci.yaml b/dts/upstream/Bindings/mmc/marvell,xenon-sdhci.yaml new file mode 100644 index 00000000000..3a8e74894ae --- /dev/null +++ b/dts/upstream/Bindings/mmc/marvell,xenon-sdhci.yaml @@ -0,0 +1,277 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/marvell,xenon-sdhci.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell Xenon SDHCI Controller + +description: | + This file documents differences between the core MMC properties described by + mmc-controller.yaml and the properties used by the Xenon implementation. + + Multiple SDHCs might be put into a single Xenon IP, to save size and cost. + Each SDHC is independent and owns independent resources, such as register + sets, clock and PHY. + + Each SDHC should have an independent device tree node. + +maintainers: + - Ulf Hansson <ulf.hansson@linaro.org> + +properties: + compatible: + oneOf: + - enum: + - marvell,armada-cp110-sdhci + - marvell,armada-ap806-sdhci + + - items: + - const: marvell,armada-ap807-sdhci + - const: marvell,armada-ap806-sdhci + + - items: + - const: marvell,armada-3700-sdhci + - const: marvell,sdhci-xenon + + reg: + minItems: 1 + maxItems: 2 + description: | + For "marvell,armada-3700-sdhci", two register areas. The first one + for Xenon IP register. The second one for the Armada 3700 SoC PHY PAD + Voltage Control register. Please follow the examples with compatible + "marvell,armada-3700-sdhci" in below. + Please also check property marvell,pad-type in below. + + For other compatible strings, one register area for Xenon IP. + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: core + - const: axi + + interrupts: + maxItems: 1 + + marvell,xenon-sdhc-id: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + description: | + Indicate the corresponding bit index of current SDHC in SDHC System + Operation Control Register Bit[7:0]. Set/clear the corresponding bit to + enable/disable current SDHC. + + marvell,xenon-phy-type: + $ref: /schemas/types.yaml#/definitions/string + enum: + - emmc 5.1 phy + - emmc 5.0 phy + description: | + Xenon support multiple types of PHYs. To select eMMC 5.1 PHY, set: + marvell,xenon-phy-type = "emmc 5.1 phy" eMMC 5.1 PHY is the default + choice if this property is not provided. To select eMMC 5.0 PHY, set: + marvell,xenon-phy-type = "emmc 5.0 phy" + + All those types of PHYs can support eMMC, SD and SDIO. Please note that + this property only presents the type of PHY. It doesn't stand for the + entire SDHC type or property. For example, "emmc 5.1 phy" doesn't mean + that this Xenon SDHC only supports eMMC 5.1. + + marvell,xenon-phy-znr: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 0x1f + default: 0xf + description: | + Set PHY ZNR value. + Only available for eMMC PHY. + + marvell,xenon-phy-zpr: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 0x1f + default: 0xf + description: | + Set PHY ZPR value. + Only available for eMMC PHY. + + marvell,xenon-phy-nr-success-tun: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + default: 0x4 + description: | + Set the number of required consecutive successful sampling points + used to identify a valid sampling window, in tuning process. + + marvell,xenon-phy-tun-step-divider: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 64 + description: | + Set the divider for calculating TUN_STEP. + + marvell,xenon-phy-slow-mode: + type: boolean + description: | + If this property is selected, transfers will bypass PHY. + Only available when bus frequency lower than 55MHz in SDR mode. + Disabled by default. Please only try this property if timing issues + always occur with PHY enabled in eMMC HS SDR, SD SDR12, SD SDR25, + SD Default Speed and HS mode and eMMC legacy speed mode. + + marvell,xenon-tun-count: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0x9 + description: | + Xenon SDHC SoC usually doesn't provide re-tuning counter in + Capabilities Register 3 Bit[11:8]. + This property provides the re-tuning counter. + +allOf: + - $ref: mmc-controller.yaml# + - if: + properties: + compatible: + contains: + const: marvell,armada-3700-sdhci + + then: + properties: + reg: + items: + - description: Xenon IP registers + - description: Armada 3700 SoC PHY PAD Voltage Control register + + marvell,pad-type: + $ref: /schemas/types.yaml#/definitions/string + enum: + - sd + - fixed-1-8v + description: | + Type of Armada 3700 SoC PHY PAD Voltage Controller register. + If "sd" is selected, SoC PHY PAD is set as 3.3V at the beginning + and is switched to 1.8V when later in higher speed mode. + If "fixed-1-8v" is selected, SoC PHY PAD is fixed 1.8V, such as for + eMMC. + Please follow the examples with compatible + "marvell,armada-3700-sdhci" in below. + + required: + - marvell,pad-type + + - if: + properties: + compatible: + contains: + enum: + - marvell,armada-cp110-sdhci + - marvell,armada-ap807-sdhci + - marvell,armada-ap806-sdhci + + then: + properties: + clocks: + minItems: 2 + + clock-names: + items: + - const: core + - const: axi + + +required: + - compatible + - reg + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + // For eMMC + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mmc@aa0000 { + compatible = "marvell,armada-ap807-sdhci", "marvell,armada-ap806-sdhci"; + reg = <0xaa0000 0x1000>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&emmc_clk 0>, <&axi_clk 0>; + clock-names = "core", "axi"; + bus-width = <4>; + marvell,xenon-phy-slow-mode; + marvell,xenon-tun-count = <11>; + non-removable; + no-sd; + no-sdio; + + /* Vmmc and Vqmmc are both fixed */ + }; + + - | + // For SD/SDIO + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mmc@ab0000 { + compatible = "marvell,armada-cp110-sdhci"; + reg = <0xab0000 0x1000>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + vqmmc-supply = <&sd_vqmmc_regulator>; + vmmc-supply = <&sd_vmmc_regulator>; + clocks = <&sdclk 0>, <&axi_clk 0>; + clock-names = "core", "axi"; + bus-width = <4>; + marvell,xenon-tun-count = <9>; + }; + + - | + // For eMMC with compatible "marvell,armada-3700-sdhci": + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mmc@aa0000 { + compatible = "marvell,armada-3700-sdhci", "marvell,sdhci-xenon"; + reg = <0xaa0000 0x1000>, + <0x17808 0x4>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&emmcclk 0>; + clock-names = "core"; + bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs400-1_8v; + non-removable; + no-sd; + no-sdio; + + /* Vmmc and Vqmmc are both fixed */ + + marvell,pad-type = "fixed-1-8v"; + }; + + - | + // For SD/SDIO with compatible "marvell,armada-3700-sdhci": + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + + mmc@ab0000 { + compatible = "marvell,armada-3700-sdhci", "marvell,sdhci-xenon"; + reg = <0xab0000 0x1000>, + <0x17808 0x4>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + vqmmc-supply = <&sd_regulator>; + /* Vmmc is fixed */ + clocks = <&sdclk 0>; + clock-names = "core"; + bus-width = <4>; + + marvell,pad-type = "sd"; + }; |