1 files changed, 120 insertions, 0 deletions
diff --git a/dts/upstream/Bindings/mtd/jedec,spi-nor.yaml b/dts/upstream/Bindings/mtd/jedec,spi-nor.yaml
new file mode 100644
index 00000000000..58f0cea160e
--- /dev/null
+++ b/dts/upstream/Bindings/mtd/jedec,spi-nor.yaml
@@ -0,0 +1,120 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mtd/jedec,spi-nor.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SPI NOR flash ST M25Pxx (and similar) serial flash chips
+
+maintainers:
+  - Rob Herring <robh@kernel.org>
+
+allOf:
+  - $ref: mtd.yaml#
+  - $ref: /schemas/spi/spi-peripheral-props.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - pattern: "^((((micron|spansion|st),)?\
+              (m25p(40|80|16|32|64|128)|\
+              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
+              atmel,at25df(321a|641|081a)|\
+              everspin,mr25h(10|40|128|256)|\
+              (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\
+              (mxicy|macronix),mx25u(4033|4035)|\
+              (spansion,)?s25fl(128s|256s1|512s|008k|064k|164k)|\
+              (sst|microchip),sst25vf(016b|032b|040b)|\
+              (sst,)?sst26wf016b|\
+              (sst,)?sst25wf(040b|080)|\
+              winbond,w25x(80|32)|\
+              (winbond,)?w25q(16|32(w|dw)?|64(dw)?|80bl|128(fw)?|256))$"
+          - const: jedec,spi-nor
+      - items:
+          - enum:
+              - issi,is25lp016d
+              - micron,mt25qu02g
+              - mxicy,mx25r1635f
+              - mxicy,mx25u6435f
+              - mxicy,mx25v8035f
+              - spansion,s25sl12801
+              - spansion,s25fs512s
+          - const: jedec,spi-nor
+      - const: jedec,spi-nor
+    description:
+      SPI NOR flashes compatible with the JEDEC SFDP standard or which may be
+      identified with the READ ID opcode (0x9F) do not deserve a specific
+      compatible. They should instead only be matched against the generic
+      "jedec,spi-nor" compatible.
+
+  reg:
+    minItems: 1
+    maxItems: 2
+
+  m25p,fast-read:
+    type: boolean
+    description:
+      Use the "fast read" opcode to read data from the chip instead of the usual
+      "read" opcode. This opcode is not supported by all chips and support for
+      it can not be detected at runtime. Refer to your chips' datasheet to check
+      if this is supported by your chip.
+
+  broken-flash-reset:
+    type: boolean
+    description:
+      Some flash devices utilize stateful addressing modes (e.g., for 32-bit
+      addressing) which need to be managed carefully by a system. Because these
+      sorts of flash don't have a standardized software reset command, and
+      because some systems don't toggle the flash RESET# pin upon system reset
+      (if the pin even exists at all), there are systems which cannot reboot
+      properly if the flash is left in the "wrong" state. This boolean flag can
+      be used on such systems, to denote the absence of a reliable reset
+      mechanism.
+
+  no-wp:
+    type: boolean
+    description:
+      The status register write disable (SRWD) bit in status register, combined
+      with the WP# signal, provides hardware data protection for the device. When
+      the SRWD bit is set to 1, and the WP# signal is either driven LOW or hard
+      strapped to LOW, the status register nonvolatile bits become read-only and
+      the WRITE STATUS REGISTER operation will not execute. The only way to exit
+      this hardware-protected mode is to drive WP# HIGH. If the WP# signal of the
+      flash device is not connected or is wrongly tied to GND (that includes internal
+      pull-downs) then status register permanently becomes read-only as the SRWD bit
+      cannot be reset. This boolean flag can be used on such systems to avoid setting
+      the SRWD bit while writing the status register. WP# signal hard strapped to GND
+      can be a valid use case.
+
+  reset-gpios:
+    description:
+      A GPIO line connected to the RESET (active low) signal of the device.
+      If "broken-flash-reset" is present then having this property does not
+      make any difference.
+
+  spi-cpol: true
+  spi-cpha: true
+
+dependencies:
+  spi-cpol: [ spi-cpha ]
+  spi-cpha: [ spi-cpol ]
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        flash@0 {
+            compatible = "spansion,m25p80", "jedec,spi-nor";
+            reg = <0>;
+            spi-max-frequency = <40000000>;
+            m25p,fast-read;
+            reset-gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+        };
+    };
+...