1 files changed, 116 insertions, 0 deletions
diff --git a/dts/upstream/Bindings/net/mdio.yaml b/dts/upstream/Bindings/net/mdio.yaml
new file mode 100644
index 00000000000..a266ade918c
--- /dev/null
+++ b/dts/upstream/Bindings/net/mdio.yaml
@@ -0,0 +1,116 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/mdio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MDIO Bus Common Properties
+
+maintainers:
+  - Andrew Lunn <andrew@lunn.ch>
+  - Florian Fainelli <f.fainelli@gmail.com>
+  - Heiner Kallweit <hkallweit1@gmail.com>
+
+description:
+  These are generic properties that can apply to any MDIO bus. Any
+  MDIO bus must have a list of child nodes, one per device on the
+  bus. These should follow the generic ethernet-phy.yaml document, or
+  a device specific binding document.
+
+properties:
+  $nodename:
+    pattern: "^mdio(@.*)?"
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      The phandle and specifier for the GPIO that controls the RESET
+      lines of all devices on that MDIO bus.
+
+  reset-delay-us:
+    description:
+      RESET pulse width in microseconds. It applies to all MDIO devices
+      and must therefore be appropriately determined based on all devices
+      requirements (maximum value of all per-device RESET pulse widths).
+
+  reset-post-delay-us:
+    description:
+      Delay after reset deassert in microseconds. It applies to all MDIO
+      devices and it's determined by how fast all devices are ready for
+      communication. This delay happens just before e.g. Ethernet PHY
+      type ID auto detection.
+
+  clock-frequency:
+    description:
+      Desired MDIO bus clock frequency in Hz. Values greater than IEEE 802.3
+      defined 2.5MHz should only be used when all devices on the bus support
+      the given clock speed.
+
+  suppress-preamble:
+    description:
+      The 32 bit preamble should be suppressed. In order for this to
+      work, all devices on the bus must support suppressed preamble.
+    type: boolean
+
+patternProperties:
+  '@[0-9a-f]+$':
+    type: object
+
+    properties:
+      reg:
+        minimum: 0
+        maximum: 31
+        description:
+          The ID number for the device.
+
+      broken-turn-around:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description:
+          If set, indicates the MDIO device does not correctly release
+          the turn around line low at end of the control phase of the
+          MDIO transaction.
+
+      reset-gpios:
+        maxItems: 1
+        description:
+          The GPIO phandle and specifier for the MDIO reset signal.
+
+      reset-assert-us:
+        description:
+          Delay after the reset was asserted in microseconds. If this
+          property is missing the delay will be skipped.
+
+      reset-deassert-us:
+        description:
+          Delay after the reset was deasserted in microseconds. If
+          this property is missing the delay will be skipped.
+
+    required:
+      - reg
+
+additionalProperties: true
+
+examples:
+  - |
+    davinci_mdio: mdio@5c030000 {
+        reg = <0x5c030000 0x1000>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        reset-gpios = <&gpio2 5 1>;
+        reset-delay-us = <2>;
+
+        ethphy0: ethernet-phy@1 {
+            reg = <1>;
+        };
+
+        ethphy1: ethernet-phy@3 {
+            reg = <3>;
+        };
+    };