diff options
Diffstat (limited to 'dts/upstream/Bindings/usb/chipidea,usb2-common.yaml')
| -rw-r--r-- | dts/upstream/Bindings/usb/chipidea,usb2-common.yaml | 200 |
1 files changed, 200 insertions, 0 deletions
diff --git a/dts/upstream/Bindings/usb/chipidea,usb2-common.yaml b/dts/upstream/Bindings/usb/chipidea,usb2-common.yaml new file mode 100644 index 00000000000..d2a7d2ecf48 --- /dev/null +++ b/dts/upstream/Bindings/usb/chipidea,usb2-common.yaml @@ -0,0 +1,200 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/usb/chipidea,usb2-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: USB2 ChipIdea USB controller Common Properties + +maintainers: + - Xu Yang <xu.yang_2@nxp.com> + +properties: + reg: + minItems: 1 + maxItems: 2 + + interrupts: + minItems: 1 + maxItems: 2 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + minItems: 1 + maxItems: 3 + + dr_mode: true + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + reset-names: + maxItems: 1 + + "#reset-cells": + const: 1 + + phy_type: true + + itc-setting: + description: + interrupt threshold control register control, the setting should be + aligned with ITC bits at register USBCMD. + $ref: /schemas/types.yaml#/definitions/uint32 + + ahb-burst-config: + description: + it is vendor dependent, the required value should be aligned with + AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This property is + used to change AHB burst configuration, check the chipidea spec for + meaning of each value. If this property is not existed, it will use + the reset value. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x7 + + tx-burst-size-dword: + description: + it is vendor dependent, the tx burst size in dword (4 bytes), This + register represents the maximum length of a the burst in 32-bit + words while moving data from system memory to the USB bus, the value + of this property will only take effect if property "ahb-burst-config" + is set to 0, if this property is missing the reset default of the + hardware implementation will be used. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x20 + + rx-burst-size-dword: + description: + it is vendor dependent, the rx burst size in dword (4 bytes), This + register represents the maximum length of a the burst in 32-bit words + while moving data from the USB bus to system memory, the value of + this property will only take effect if property "ahb-burst-config" + is set to 0, if this property is missing the reset default of the + hardware implementation will be used. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0x0 + maximum: 0x20 + + extcon: + description: + Phandles to external connector devices. First phandle should point + to external connector, which provide "USB" cable events, the second + should point to external connector device, which provide "USB-HOST" + cable events. If one of the external connector devices is not + required, empty <0> phandle should be specified. + $ref: /schemas/types.yaml#/definitions/phandle-array + minItems: 1 + items: + - description: vbus extcon + - description: id extcon + + phy-clkgate-delay-us: + description: + The delay time (us) between putting the PHY into low power mode and + gating the PHY clock. + + non-zero-ttctrl-ttha: + description: + After setting this property, the value of register ttctrl.ttha + will be 0x7f; if not, the value will be 0x0, this is the default + value. It needs to be very carefully for setting this property, it + is recommended that consult with your IC engineer before setting + this value. On the most of chipidea platforms, the "usage_tt" flag + at RTL is 0, so this property only affects siTD. + + If this property is not set, the max packet size is 1023 bytes, and + if the total of packet size for previous transactions are more than + 256 bytes, it can't accept any transactions within this frame. The + use case is single transaction, but higher frame rate. + + If this property is set, the max packet size is 188 bytes, it can + handle more transactions than above case, it can accept transactions + until it considers the left room size within frame is less than 188 + bytes, software needs to make sure it does not send more than 90% + maximum_periodic_data_per_frame. The use case is multiple + transactions, but less frame rate. + type: boolean + + mux-controls: + description: + The mux control for toggling host/device output of this controller. + It's expected that a mux state of 0 indicates device mode and a mux + state of 1 indicates host mode. + maxItems: 1 + + mux-control-names: + const: usb_switch + + pinctrl-names: + description: + Names for optional pin modes in "default", "host", "device". + In case of HSIC-mode, "idle" and "active" pin modes are mandatory. + In this case, the "idle" state needs to pull down the data and + strobe pin and the "active" state needs to pull up the strobe pin. + oneOf: + - items: + - const: idle + - const: active + - items: + - const: default + - const: host + - const: device + - items: + - const: default + - enum: + - host + - device + - items: + - const: default + + pinctrl-0: + maxItems: 1 + + pinctrl-1: + maxItems: 1 + + phys: + maxItems: 1 + + phy-names: + const: usb-phy + + vbus-supply: + description: reference to the VBUS regulator. + + usb-phy: + description: phandle for the PHY device. Use "phys" instead. + maxItems: 1 + deprecated: true + + port: + description: + Any connector to the data bus of this controller should be modelled + using the OF graph bindings specified, if the "usb-role-switch" + property is used. + $ref: /schemas/graph.yaml#/properties/port + + reset-gpios: + maxItems: 1 + +dependencies: + port: [ usb-role-switch ] + mux-controls: [ mux-control-names ] + +required: + - reg + - interrupts + +allOf: + - $ref: usb-hcd.yaml# + - $ref: usb-drd.yaml# + +additionalProperties: true |