diff options
Diffstat (limited to 'dts/upstream/src/arm64/allwinner/sun50i-a64-olinuxino.dts')
| -rw-r--r-- | dts/upstream/src/arm64/allwinner/sun50i-a64-olinuxino.dts | 377 |
1 files changed, 377 insertions, 0 deletions
diff --git a/dts/upstream/src/arm64/allwinner/sun50i-a64-olinuxino.dts b/dts/upstream/src/arm64/allwinner/sun50i-a64-olinuxino.dts new file mode 100644 index 00000000000..fd3794678c3 --- /dev/null +++ b/dts/upstream/src/arm64/allwinner/sun50i-a64-olinuxino.dts @@ -0,0 +1,377 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2017 Jagan Teki <jteki@openedev.com> + +/dts-v1/; + +#include "sun50i-a64.dtsi" +#include "sun50i-a64-cpu-opp.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Olimex A64-Olinuxino"; + compatible = "olimex,a64-olinuxino", "allwinner,sun50i-a64"; + + aliases { + ethernet0 = &emac; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con_in: endpoint { + remote-endpoint = <&hdmi_out_con>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + label = "a64-olinuxino:red:user"; + gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */ + }; + }; + + reg_usb1_vbus: usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 6 9 GPIO_ACTIVE_HIGH>; /* PG9 */ + status = "okay"; + }; + + wifi_pwrseq: pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ + }; +}; + +&codec { + status = "okay"; +}; + +&codec_analog { + cpvdd-supply = <®_eldo1>; + status = "okay"; +}; + +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + +&cpu1 { + cpu-supply = <®_dcdc2>; +}; + +&cpu2 { + cpu-supply = <®_dcdc2>; +}; + +&cpu3 { + cpu-supply = <®_dcdc2>; +}; + +&dai { + status = "okay"; +}; + +&de { + status = "okay"; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci1 { + status = "okay"; +}; + +&emac { + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins>; + phy-mode = "rgmii"; + phy-handle = <&ext_rgmii_phy>; + phy-supply = <®_dcdc1>; + allwinner,tx-delay-ps = <600>; + status = "okay"; +}; + +&hdmi { + hvcc-supply = <®_dldo1>; + status = "okay"; +}; + +&hdmi_out { + hdmi_out_con: endpoint { + remote-endpoint = <&hdmi_con_in>; + }; +}; + +&mdio { + ext_rgmii_phy: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&mmc0 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + vmmc-supply = <®_dcdc1>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; + disable-wp; + bus-width = <4>; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dldo4>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; + + rtl8723bs: wifi@1 { + reg = <1>; + interrupt-parent = <&r_pio>; + interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */ + interrupt-names = "host-wake"; + }; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&pio { + vcc-pc-supply = <®_dcdc1>; + vcc-pd-supply = <®_dcdc1>; + vcc-pe-supply = <®_aldo1>; + vcc-pg-supply = <®_dldo4>; +}; + +&r_pio { + /* + * FIXME: We can't add that supply for now since it would + * create a circular dependency between pinctrl, the regulator + * and the RSB Bus. + * + * vcc-pl-supply = <®_aldo2>; + */ +}; + +&pio { + vcc-pa-supply = <®_dcdc1>; + vcc-pb-supply = <®_dcdc1>; + vcc-pc-supply = <®_dcdc1>; + vcc-pd-supply = <®_dcdc1>; + vcc-pe-supply = <®_aldo1>; + vcc-pf-supply = <®_dcdc1>; + vcc-pg-supply = <®_dldo4>; + vcc-ph-supply = <®_dcdc1>; +}; + +&r_rsb { + status = "okay"; + + axp803: pmic@3a3 { + compatible = "x-powers,axp803"; + reg = <0x3a3>; + interrupt-parent = <&r_intc>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; + x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ + }; +}; + +/* VCC-PL is powered by aldo2 but we cannot add it as the RSB */ +/* interface used to talk to the PMIC in on the PL pins */ +/* &r_pio { */ +/* vcc-pl-supply = <®_aldo2>; */ +/* }; */ + +#include "axp803.dtsi" + +&ac_power_supply { + status = "okay"; +}; + +&battery_power_supply { + status = "okay"; +}; + +®_aldo1 { + regulator-always-on; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vcc-pe"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-pl"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-pll-avcc"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-3v3"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1040000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-cpux"; +}; + +/* DCDC3 is polyphased with DCDC2 */ + +/* + * The board uses DDR3L DRAM chips. 1.36V is the closest to the nominal + * 1.35V that the PMIC can drive. + */ +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1360000>; + regulator-max-microvolt = <1360000>; + regulator-name = "vcc-ddr3"; +}; + +®_dcdc6 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-sys"; +}; + +®_dldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-hdmi"; +}; + +®_dldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-mipi"; +}; + +®_dldo3 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-name = "vcc-avdd-csi"; +}; + +®_dldo4 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-io"; +}; + +®_drivevbus { + regulator-name = "usb0-vbus"; + status = "okay"; +}; + +®_eldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "cpvdd"; +}; + +®_eldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc-dvdd-csi"; +}; + +®_fldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-name = "vcc-1v2-hsic"; +}; + +/* + * The A64 chip cannot work without this regulator off, although + * it seems to be only driving the AR100 core. + * Maybe we don't still know well about CPUs domain. + */ +®_fldo2 { + regulator-always-on; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-name = "vdd-cpus"; +}; + +®_rtc_ldo { + regulator-name = "vcc-rtc"; +}; + +&simplefb_hdmi { + vcc-hdmi-supply = <®_dldo1>; +}; + +&sound { + simple-audio-card,aux-devs = <&codec_analog>; + simple-audio-card,widgets = "Microphone", "Microphone Jack Left", + "Microphone", "Microphone Jack Right", + "Headphone", "Headphone Jack"; + simple-audio-card,routing = "Left DAC", "DACL", + "Right DAC", "DACR", + "Headphone Jack", "HP", + "ADCL", "Left ADC", + "ADCR", "Right ADC", + "Microphone Jack Left", "MBIAS", + "MIC1", "Microphone Jack Left", + "Microphone Jack Right", "MBIAS", + "MIC2", "Microphone Jack Right"; + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + +&usbphy { + status = "okay"; + usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus-supply = <®_usb1_vbus>; +}; |