1 files changed, 144 insertions, 0 deletions
diff --git a/dts/upstream/src/arm64/allwinner/sun50i-h618-longanpi-3h.dts b/dts/upstream/src/arm64/allwinner/sun50i-h618-longanpi-3h.dts
new file mode 100644
index 00000000000..18b29c6b867
--- /dev/null
+++ b/dts/upstream/src/arm64/allwinner/sun50i-h618-longanpi-3h.dts
@@ -0,0 +1,144 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) Jisheng Zhang <jszhang@kernel.org>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h618-longan-module-3h.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Sipeed Longan Pi 3H";
+	compatible = "sipeed,longan-pi-3h", "sipeed,longan-module-3h", "allwinner,sun50i-h618";
+
+	aliases {
+		ethernet0 = &emac0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_ORANGE>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <0>;
+			gpios = <&pio 6 2 GPIO_ACTIVE_LOW>; /* PG2 */
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_ORANGE>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <1>;
+			gpios = <&pio 6 4 GPIO_ACTIVE_LOW>; /* PG4 */
+		};
+	};
+
+	reg_vcc5v: regulator-vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_vcc5v>;
+	};
+};
+
+&axp313 {
+	vin1-supply = <&reg_vcc5v>;
+	vin2-supply = <&reg_vcc5v>;
+	vin3-supply = <&reg_vcc5v>;
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+/* WiFi & BT combo module is connected to this Host */
+&ehci3 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&emac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	allwinner,rx-delay-ps = <3100>;
+	allwinner,tx-delay-ps = <700>;
+	phy-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
+
+&mdio0 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;	/* PF6 */
+	vmmc-supply = <&reg_vcc3v3>;
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usbotg {
+	/*
+	 * PHY0 pins are connected to a USB-C socket, but a role switch
+	 * is not implemented: both CC pins are pulled to GND.
+	 * The VBUS pins power the device, so a fixed peripheral mode
+	 * is the best choice.
+	 * The board can be powered via GPIOs, in this case port0 *can*
+	 * act as a host (with a cable/adapter ignoring CC), as VBUS is
+	 * then provided by the GPIOs. Any user of this setup would
+	 * need to adjust the DT accordingly: dr_mode set to "host",
+	 * enabling OHCI0 and EHCI0.
+	 */
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbphy {
+	usb1_vbus-supply = <&reg_vcc5v>;
+	usb2_vbus-supply = <&reg_vcc5v>;
+	status = "okay";
+};