diff options
Diffstat (limited to 'dts/upstream/src/arm64/amlogic/meson-g12b-odroid-n2.dtsi')
| -rw-r--r-- | dts/upstream/src/arm64/amlogic/meson-g12b-odroid-n2.dtsi | 302 |
1 files changed, 302 insertions, 0 deletions
diff --git a/dts/upstream/src/arm64/amlogic/meson-g12b-odroid-n2.dtsi b/dts/upstream/src/arm64/amlogic/meson-g12b-odroid-n2.dtsi new file mode 100644 index 00000000000..d80dd9a3da3 --- /dev/null +++ b/dts/upstream/src/arm64/amlogic/meson-g12b-odroid-n2.dtsi @@ -0,0 +1,302 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#include "meson-g12b-odroid.dtsi" + +/ { + aliases { + rtc0 = &rtc; + }; + + dio2133: audio-amplifier-0 { + compatible = "simple-audio-amplifier"; + enable-gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>; + VCC-supply = <&vcc_5v>; + sound-name-prefix = "U19"; + status = "okay"; + }; + + hub_5v: regulator-hub-5v { + compatible = "regulator-fixed"; + regulator-name = "HUB_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + + /* Connected to the Hub CHIPENABLE, LOW sets low power state */ + gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + sound { + compatible = "amlogic,axg-sound-card"; + model = "ODROID-N2"; + audio-widgets = "Line", "Lineout"; + audio-aux-devs = <&tdmout_b>, <&tdmout_c>, <&tdmin_a>, + <&tdmin_b>, <&tdmin_c>, <&tdmin_lb>, + <&dio2133>; + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", + "TDMOUT_B IN 1", "FRDDR_B OUT 1", + "TDMOUT_B IN 2", "FRDDR_C OUT 1", + "TDM_B Playback", "TDMOUT_B OUT", + "TDMOUT_C IN 0", "FRDDR_A OUT 2", + "TDMOUT_C IN 1", "FRDDR_B OUT 2", + "TDMOUT_C IN 2", "FRDDR_C OUT 2", + "TDM_C Playback", "TDMOUT_C OUT", + "TDMIN_A IN 4", "TDM_B Loopback", + "TDMIN_B IN 4", "TDM_B Loopback", + "TDMIN_C IN 4", "TDM_B Loopback", + "TDMIN_LB IN 1", "TDM_B Loopback", + "TDMIN_A IN 5", "TDM_C Loopback", + "TDMIN_B IN 5", "TDM_C Loopback", + "TDMIN_C IN 5", "TDM_C Loopback", + "TDMIN_LB IN 2", "TDM_C Loopback", + "TODDR_A IN 0", "TDMIN_A OUT", + "TODDR_B IN 0", "TDMIN_A OUT", + "TODDR_C IN 0", "TDMIN_A OUT", + "TODDR_A IN 1", "TDMIN_B OUT", + "TODDR_B IN 1", "TDMIN_B OUT", + "TODDR_C IN 1", "TDMIN_B OUT", + "TODDR_A IN 2", "TDMIN_C OUT", + "TODDR_B IN 2", "TDMIN_C OUT", + "TODDR_C IN 2", "TDMIN_C OUT", + "TODDR_A IN 6", "TDMIN_LB OUT", + "TODDR_B IN 6", "TDMIN_LB OUT", + "TODDR_C IN 6", "TDMIN_LB OUT", + "U19 INL", "ACODEC LOLP", + "U19 INR", "ACODEC LORP", + "Lineout", "U19 OUTL", + "Lineout", "U19 OUTR"; + + assigned-clocks = <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL0>, + <&clkc CLKID_MPLL1>; + assigned-clock-parents = <0>, <0>, <0>; + assigned-clock-rates = <294912000>, + <270950400>, + <393216000>; + + dai-link-0 { + sound-dai = <&frddr_a>; + }; + + dai-link-1 { + sound-dai = <&frddr_b>; + }; + + dai-link-2 { + sound-dai = <&frddr_c>; + }; + + dai-link-3 { + sound-dai = <&toddr_a>; + }; + + dai-link-4 { + sound-dai = <&toddr_b>; + }; + + dai-link-5 { + sound-dai = <&toddr_c>; + }; + + /* 8ch hdmi interface */ + dai-link-6 { + sound-dai = <&tdmif_b>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + dai-tdm-slot-tx-mask-1 = <1 1>; + dai-tdm-slot-tx-mask-2 = <1 1>; + dai-tdm-slot-tx-mask-3 = <1 1>; + mclk-fs = <256>; + + codec-0 { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; + }; + + codec-1 { + sound-dai = <&toacodec TOACODEC_IN_B>; + }; + }; + + /* i2s jack output interface */ + dai-link-7 { + sound-dai = <&tdmif_c>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + mclk-fs = <256>; + + codec-0 { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_C>; + }; + + codec-1 { + sound-dai = <&toacodec TOACODEC_IN_C>; + }; + }; + + /* hdmi glue */ + dai-link-8 { + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; + + codec { + sound-dai = <&hdmi_tx>; + }; + }; + + /* acodec glue */ + dai-link-9 { + sound-dai = <&toacodec TOACODEC_OUT>; + + codec { + sound-dai = <&acodec>; + }; + }; + }; +}; + +&acodec { + AVDD-supply = <&vddao_1v8>; + status = "okay"; +}; + +ðmac { + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; +}; + +&ext_mdio { + external_phy: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + max-speed = <1000>; + + reset-assert-us = <10000>; + reset-deassert-us = <80000>; + reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; + + interrupt-parent = <&gpio_intc>; + /* MAC_INTR on GPIOZ_14 */ + interrupts = <IRQID_GPIOZ_14 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&gpio { + gpio-line-names = + /* GPIOZ */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* GPIOH */ + "", "", "", "", "", "", "", "", + "", + /* BOOT */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* GPIOC */ + "", "", "", "", "", "", "", "", + /* GPIOA */ + "PIN_44", /* GPIOA_0 */ + "PIN_46", /* GPIOA_1 */ + "PIN_45", /* GPIOA_2 */ + "PIN_47", /* GPIOA_3 */ + "PIN_26", /* GPIOA_4 */ + "", "", "", "", "", "", + "PIN_42", /* GPIOA_11 */ + "PIN_32", /* GPIOA_12 */ + "PIN_7", /* GPIOA_13 */ + "PIN_27", /* GPIOA_14 */ + "PIN_28", /* GPIOA_15 */ + /* GPIOX */ + "PIN_16", /* GPIOX_0 */ + "PIN_18", /* GPIOX_1 */ + "PIN_22", /* GPIOX_2 */ + "PIN_11", /* GPIOX_3 */ + "PIN_13", /* GPIOX_4 */ + "PIN_33", /* GPIOX_5 */ + "PIN_35", /* GPIOX_6 */ + "PIN_15", /* GPIOX_7 */ + "PIN_19", /* GPIOX_8 */ + "PIN_21", /* GPIOX_9 */ + "PIN_24", /* GPIOX_10 */ + "PIN_23", /* GPIOX_11 */ + "PIN_8", /* GPIOX_12 */ + "PIN_10", /* GPIOX_13 */ + "PIN_29", /* GPIOX_14 */ + "PIN_31", /* GPIOX_15 */ + "PIN_12", /* GPIOX_16 */ + "PIN_3", /* GPIOX_17 */ + "PIN_5", /* GPIOX_18 */ + "PIN_36"; /* GPIOX_19 */ + /* + * WARNING: The USB Hub on the Odroid-N2 needs a reset signal + * to be turned high in order to be detected by the USB Controller + * This signal should be handled by a USB specific power sequence + * in order to reset the Hub when USB bus is powered down. + */ + usb-hub-hog { + gpio-hog; + gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb-hub-reset"; + }; +}; + +&i2c3 { + status = "okay"; + pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>; + pinctrl-names = "default"; + + rtc: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + wakeup-source; + }; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; + linux,rc-map-name = "rc-odroid"; +}; + +/* + * EMMC_D4, EMMC_D5, EMMC_D6 and EMMC_D7 pins are shared between SPI NOR pins + * and eMMC Data 4 to 7 pins. + * Replace emmc_data_8b_pins to emmc_data_4b_pins from sd_emmc_c pinctrl-0, + * and change bus-width to 4 then spifc can be enabled. + * The SW1 slide should also be set to the correct position. + */ +&spifc { + status = "disabled"; + pinctrl-0 = <&nor_pins>; + pinctrl-names = "default"; + + mx25u64: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "mxicy,mx25u6435f", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <104000000>; + }; +}; + +&toacodec { + status = "okay"; +}; + +&usb { + vbus-supply = <&usb_pwr_en>; +}; + +&usb2_phy1 { + /* Enable the hub which is connected to this port */ + phy-supply = <&hub_5v>; +}; |