diff options
Diffstat (limited to 'dts/upstream/src/arm64/freescale/mba8mx.dtsi')
| -rw-r--r-- | dts/upstream/src/arm64/freescale/mba8mx.dtsi | 381 |
1 files changed, 381 insertions, 0 deletions
diff --git a/dts/upstream/src/arm64/freescale/mba8mx.dtsi b/dts/upstream/src/arm64/freescale/mba8mx.dtsi new file mode 100644 index 00000000000..815241526a0 --- /dev/null +++ b/dts/upstream/src/arm64/freescale/mba8mx.dtsi @@ -0,0 +1,381 @@ +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT) +/* + * Copyright 2020-2021 TQ-Systems GmbH + */ + +#include <dt-bindings/net/ti-dp83867.h> + +/* TQ-Systems GmbH MBa8Mx baseboard */ + +/ { + backlight_lvds: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm3 0 5000000 0>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_12v>; + enable-gpios = <&expander2 2 GPIO_ACTIVE_HIGH>; + status = "disabled"; + }; + + beeper { + compatible = "pwm-beeper"; + pwms = <&pwm4 0 250000 0>; + beeper-hz = <4000>; + amp-supply = <®_vcc_3v3>; + }; + + chosen { + stdout-path = &uart3; + }; + + clk_xtal25: clk-xtal25 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpiobutton>; + autorepeat; + + switch-1 { + label = "switch1"; + linux,code = <BTN_0>; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + + btn2: switch-2 { + label = "switch2"; + linux,code = <BTN_1>; + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + + switch-3 { + label = "switch3"; + linux,code = <BTN_2>; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + wakeup-source; + }; + }; + + gpio_leds: gpio-leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpioled>; + + led1 { + label = "led1"; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + }; + + led2: led2 { + label = "led2"; + gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_delays: gpio-delays { + compatible = "gpio-delay"; + #gpio-cells = <3>; + gpio-controller; + gpios = <&expander0 6 GPIO_ACTIVE_HIGH>; + gpio-line-names = "LVDS_BRIDGE_EN_1V8"; + }; + + panel: panel-lvds { + /* + * Display is not fixed, so compatible has to be added from + * DT overlay + */ + backlight = <&backlight_lvds>; + power-supply = <®_vcc_3v3>; + status = "disabled"; + + port { + panel_in_lvds: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_bridge_out>; + }; + }; + }; + + reg_12v: regulator-12v { + compatible = "regulator-fixed"; + regulator-name = "MBA8MX_12V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + reg_hub_vbus: regulator-hub-vbus { + compatible = "regulator-fixed"; + regulator-name = "MBA8MX_HUB_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_sn65dsi83_1v8: regulator-sn65dsi83-1v8 { + compatible = "regulator-fixed"; + regulator-name = "SN65DSI83_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&expander0 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_vcc_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "MBA8MX_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + sound { + compatible = "fsl,imx-audio-tlv320aic32x4"; + model = "imx-audio-tlv320aic32x4"; + ssi-controller = <&sai3>; + audio-codec = <&tlv320aic3x04>; + }; +}; + +&ecspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + phy-supply = <®_vcc_3v3>; + fsl,magic-packet; + mac-address = [ 00 00 00 00 00 00 ]; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@e { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0xe>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,dp83867-rxctrl-strap-quirk; + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; + enet-phy-lane-no-swap; + reset-gpios = <&expander2 7 GPIO_ACTIVE_LOW>; + reset-assert-us = <500000>; + reset-deassert-us = <500>; + }; + }; +}; + +&i2c1 { + expander0: gpio@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + vcc-supply = <®_vcc_3v3>; + interrupt-parent = <&gpio1>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-line-names = "", "", "", "", + "", "", "LVDS_BRIDGE_EN", "", + "", "", "", "", + "", "", "", ""; + + sd-mux-oe-hog { + gpio-hog; + gpios = <8 0>; + output-low; + line-name = "SD_MUX_EN#"; + }; + + boot-cfg-oe-hog { + gpio-hog; + gpios = <12 0>; + output-high; + line-name = "BOOT_CFG_OE#"; + }; + + rst_usb_hub_hog: rst-usb-hub-hog { + gpio-hog; + gpios = <13 0>; + output-high; + line-name = "RST_USB_HUB#"; + }; + }; + + expander1: gpio@24 { + compatible = "nxp,pca9555"; + reg = <0x24>; + gpio-controller; + #gpio-cells = <2>; + vcc-supply = <®_vcc_3v3>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c2>; + pinctrl-1 = <&pinctrl_i2c2_gpio>; + scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; + + tlv320aic3x04: audio-codec@18 { + compatible = "ti,tlv320aic32x4"; + reg = <0x18>; + reset-gpios = <&expander2 0 GPIO_ACTIVE_LOW>; + iov-supply = <®_vcc_3v3>; + ldoin-supply = <®_vcc_3v3>; + }; + + sensor1: temperator-sensor@1f { + compatible = "nxp,se97b", "jedec,jc-42.4-temp"; + reg = <0x1f>; + }; + + eeprom3: eeprom@57 { + compatible = "nxp,se97b", "atmel,24c02"; + reg = <0x57>; + pagesize = <16>; + vcc-supply = <®_vcc_3v3>; + }; + + pcieclk: clk@68 { + compatible = "renesas,9fgv0441"; + reg = <0x68>; + clocks = <&clk_xtal25>; + #clock-cells = <1>; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c3>; + pinctrl-1 = <&pinctrl_i2c3_gpio>; + scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; + + dsi_lvds_bridge: bridge@2d { + compatible = "ti,sn65dsi84"; + reg = <0x2d>; + enable-gpios = <&gpio_delays 0 130000 0>; + vcc-supply = <®_sn65dsi83_1v8>; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lvds_bridge_in: endpoint { + data-lanes = <1 2 3 4>; + remote-endpoint = <&mipi_dsi_out>; + }; + }; + + port@2 { + reg = <2>; + + lvds_bridge_out: endpoint { + remote-endpoint = <&panel_in_lvds>; + }; + }; + }; + }; +}; + +&mipi_dsi { + samsung,burst-clock-frequency = <891000000>; + samsung,esc-clock-frequency = <20000000>; +}; + +&mipi_dsi_out { + data-lanes = <1 2 3 4>; + remote-endpoint = <&lvds_bridge_in>; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; + status = "okay"; +}; + +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + #sound-dai-cells = <0>; + assigned-clock-rates = <49152000>; + status = "okay"; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +/* console */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + bus-width = <4>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + disable-wp; + no-mmc; + no-sdio; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; |