diff options
Diffstat (limited to 'dts/upstream/src/arm64/qcom/msm8916-samsung-a2015-common.dtsi')
| -rw-r--r-- | dts/upstream/src/arm64/qcom/msm8916-samsung-a2015-common.dtsi | 528 |
1 files changed, 528 insertions, 0 deletions
diff --git a/dts/upstream/src/arm64/qcom/msm8916-samsung-a2015-common.dtsi b/dts/upstream/src/arm64/qcom/msm8916-samsung-a2015-common.dtsi new file mode 100644 index 00000000000..4bbbee80b5e --- /dev/null +++ b/dts/upstream/src/arm64/qcom/msm8916-samsung-a2015-common.dtsi @@ -0,0 +1,528 @@ +// SPDX-License-Identifier: GPL-2.0-only + +#include "msm8916-pm8916.dtsi" +#include "msm8916-modem-qdsp6.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include <dt-bindings/sound/apq8016-lpass.h> + +/ { + aliases { + mmc0 = &sdhc_1; /* eMMC */ + mmc1 = &sdhc_2; /* SD card */ + serial0 = &blsp_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + reserved-memory { + /* Additional memory used by Samsung firmware modifications */ + tz-apps@85500000 { + reg = <0x0 0x85500000 0x0 0xb00000>; + no-map; + }; + }; + + clk_pwm: pwm { + compatible = "clk-pwm"; + #pwm-cells = <2>; + + clocks = <&gcc GCC_GP2_CLK>; + + pinctrl-names = "default"; + pinctrl-0 = <&motor_pwm_default>; + status = "disabled"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + button-volume-up { + label = "Volume Up"; + gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + + button-home { + label = "Home"; + gpios = <&tlmm 109 GPIO_ACTIVE_LOW>; + linux,code = <KEY_HOMEPAGE>; + }; + }; + + gpio-hall-sensor { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_hall_sensor_default>; + + label = "GPIO Hall Effect Sensor"; + + event-hall-sensor { + label = "Hall Effect Sensor"; + gpios = <&tlmm 52 GPIO_ACTIVE_LOW>; + linux,input-type = <EV_SW>; + linux,code = <SW_LID>; + linux,can-disable; + }; + }; + + /* + * NOTE: A5 connects GPIO 76 to a reglator powering the motor + * driver IC but A3 connects the same signal to an ENABLE pin of + * the driver. + */ + reg_motor_vdd: regulator-motor-vdd { + compatible = "regulator-fixed"; + regulator-name = "motor_vdd"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + + gpio = <&tlmm 76 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&motor_en_default>; + }; + + reg_vdd_tsp_a: regulator-vdd-tsp-a { + compatible = "regulator-fixed"; + regulator-name = "vdd_tsp_a"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&tsp_en_default>; + }; + + i2c-muic { + compatible = "i2c-gpio"; + sda-gpios = <&tlmm 105 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&tlmm 106 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + + pinctrl-names = "default"; + pinctrl-0 = <&muic_i2c_default>; + + #address-cells = <1>; + #size-cells = <0>; + + muic: extcon@25 { + compatible = "siliconmitus,sm5502-muic"; + + reg = <0x25>; + interrupt-parent = <&tlmm>; + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&muic_int_default>; + + usb_con: connector { + compatible = "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + }; + }; + }; + + i2c-tkey { + compatible = "i2c-gpio"; + sda-gpios = <&tlmm 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&tlmm 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + + pinctrl-names = "default"; + pinctrl-0 = <&tkey_i2c_default>; + + #address-cells = <1>; + #size-cells = <0>; + + touchkey: touchkey@20 { + /* Note: Actually an ABOV MCU that implements same interface */ + compatible = "coreriver,tc360-touchkey"; + reg = <0x20>; + + interrupt-parent = <&tlmm>; + interrupts = <98 IRQ_TYPE_EDGE_FALLING>; + + /* vcc/vdd-supply are board-specific */ + vddio-supply = <&pm8916_l6>; + + linux,keycodes = <KEY_APPSELECT KEY_BACK>; + + pinctrl-names = "default"; + pinctrl-0 = <&tkey_default>; + }; + }; + + i2c-nfc { + compatible = "i2c-gpio"; + sda-gpios = <&tlmm 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&tlmm 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + + pinctrl-names = "default"; + pinctrl-0 = <&nfc_i2c_default>; + + #address-cells = <1>; + #size-cells = <0>; + + nfc@27 { + compatible = "samsung,s3fwrn5-i2c"; + reg = <0x27>; + + interrupt-parent = <&tlmm>; + interrupts = <21 IRQ_TYPE_EDGE_RISING>; + + en-gpios = <&tlmm 20 GPIO_ACTIVE_LOW>; + wake-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; + + clocks = <&rpmcc RPM_SMD_BB_CLK2_PIN>; + + pinctrl-names = "default"; + pinctrl-0 = <&nfc_default &nfc_clk_req>; + }; + }; + + vibrator: vibrator { + compatible = "pwm-vibrator"; + + pwms = <&clk_pwm 0 100000>; + pwm-names = "enable"; + + vcc-supply = <®_motor_vdd>; + status = "disabled"; + }; +}; + +&blsp_i2c1 { + status = "okay"; + + speaker_codec: audio-codec@34 { + compatible = "nxp,tfa9895"; + reg = <0x34>; + vddd-supply = <&pm8916_l5>; + sound-name-prefix = "Speaker"; + #sound-dai-cells = <0>; + }; +}; + +&blsp_i2c2 { + status = "okay"; + + accelerometer: accelerometer@10 { + compatible = "bosch,bmc150_accel"; + reg = <0x10>; + interrupt-parent = <&tlmm>; + interrupts = <115 IRQ_TYPE_EDGE_RISING>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; + + pinctrl-names = "default"; + pinctrl-0 = <&accel_int_default>; + }; + + magnetometer@12 { + compatible = "bosch,bmc150_magn"; + reg = <0x12>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; + }; +}; + +&blsp_i2c4 { + status = "okay"; + + battery@35 { + compatible = "richtek,rt5033-battery"; + reg = <0x35>; + interrupt-parent = <&tlmm>; + interrupts = <121 IRQ_TYPE_EDGE_BOTH>; + + pinctrl-names = "default"; + pinctrl-0 = <&fg_alert_default>; + }; +}; + +&blsp_uart2 { + status = "okay"; +}; + +&gpu { + status = "okay"; +}; + +/* + * For some reason the speaker amplifier is connected to the second SD line + * (MI2S_2_D1) instead of the first (MI2S_2_D0). This must be configured in the + * device tree, otherwise audio will seemingly play fine on the wrong SD line + * but the speaker stays silent. + * + * When routing audio via QDSP6 (the default) the &lpass node is reserved and + * the definitions from &q6afedai are used. When the modem is disabled audio can + * be alternatively routed directly to the LPASS hardware with reduced latency. + * The definitions for &lpass are here for completeness to simplify changing the + * setup with minor changes to the DT (either manually or with DT overlays). + */ +&lpass { + dai-link@3 { + reg = <MI2S_QUATERNARY>; + qcom,playback-sd-lines = <1>; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dsi0 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mdss_default>; + pinctrl-1 = <&mdss_sleep>; +}; + +&mpss_mem { + reg = <0x0 0x86800000 0x0 0x5400000>; +}; + +&pm8916_resin { + status = "okay"; + linux,code = <KEY_VOLUMEDOWN>; +}; + +&pm8916_rpm_regulators { + pm8916_l17: l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; +}; + +&q6afedai { + dai@22 { + reg = <QUATERNARY_MI2S_RX>; + qcom,sd-lines = <1>; + }; +}; + +&sdhc_1 { + status = "okay"; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_default &sdc2_cd_default>; + pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>; + + cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; +}; + +&sound { + model = "samsung-a2015"; + audio-routing = + "AMIC1", "MIC BIAS External1", + "AMIC2", "MIC BIAS Internal2", + "AMIC3", "MIC BIAS External1"; + + pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>; + pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>; + pinctrl-names = "default", "sleep"; + + sound_link_backend2: backend2-dai-link { + link-name = "Quaternary MI2S"; + + cpu { + sound-dai = <&q6afedai QUATERNARY_MI2S_RX>; + }; + platform { + sound-dai = <&q6routing>; + }; + codec { + sound-dai = <&speaker_codec>; + }; + }; +}; + +&usb { + status = "okay"; + extcon = <&muic>, <&muic>; +}; + +&usb_hs_phy { + extcon = <&muic>; +}; + +&venus { + status = "okay"; +}; + +&venus_mem { + status = "okay"; +}; + +&tlmm { + accel_int_default: accel-int-default-state { + pins = "gpio115"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + fg_alert_default: fg-alert-default-state { + pins = "gpio121"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + gpio_keys_default: gpio-keys-default-state { + pins = "gpio107", "gpio109"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + gpio_hall_sensor_default: gpio-hall-sensor-default-state { + pins = "gpio52"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + mdss_default: mdss-default-state { + pins = "gpio25"; + function = "gpio"; + + drive-strength = <8>; + bias-disable; + }; + mdss_sleep: mdss-sleep-state { + pins = "gpio25"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-down; + }; + + motor_en_default: motor-en-default-state { + pins = "gpio76"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + motor_pwm_default: motor-pwm-default-state { + pins = "gpio50"; + function = "gcc_gp2_clk_a"; + }; + + muic_i2c_default: muic-i2c-default-state { + pins = "gpio105", "gpio106"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + muic_int_default: muic-int-default-state { + pins = "gpio12"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + nfc_default: nfc-default-state { + nfc-pins { + pins = "gpio20", "gpio49"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + irq-pins { + pins = "gpio21"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-down; + }; + }; + + nfc_i2c_default: nfc-i2c-default-state { + pins = "gpio0", "gpio1"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + sdc2_cd_default: sdc2-cd-default-state { + pins = "gpio38"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + tkey_default: tkey-default-state { + pins = "gpio98"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + tkey_i2c_default: tkey-i2c-default-state { + pins = "gpio16", "gpio17"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + tsp_en_default: tsp-en-default-state { + pins = "gpio73"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + ts_int_default: ts-int-default-state { + pins = "gpio13"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; +}; + +&pm8916_gpios { + nfc_clk_req: nfc-clk-req-state { + pins = "gpio2"; + function = "func1"; + + input-enable; + bias-disable; + power-source = <PM8916_GPIO_L2>; + }; +}; |