diff options
Diffstat (limited to 'dts/upstream/src/arm64/qcom/sc7180-idp.dts')
| -rw-r--r-- | dts/upstream/src/arm64/qcom/sc7180-idp.dts | 767 |
1 files changed, 767 insertions, 0 deletions
diff --git a/dts/upstream/src/arm64/qcom/sc7180-idp.dts b/dts/upstream/src/arm64/qcom/sc7180-idp.dts new file mode 100644 index 00000000000..0146fb0036d --- /dev/null +++ b/dts/upstream/src/arm64/qcom/sc7180-idp.dts @@ -0,0 +1,767 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * SC7180 IDP board device tree source + * + * Copyright (c) 2019, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include "sc7180.dtsi" +#include "sc7180-firmware-tfa.dtsi" +#include "pm6150.dtsi" +#include "pm6150l.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. SC7180 IDP"; + compatible = "qcom,sc7180-idp", "qcom,sc7180"; + + aliases { + bluetooth0 = &bluetooth; + hsuart0 = &uart3; + serial0 = &uart8; + wifi0 = &wifi; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +/* + * Reserved memory changes + * + * Delete all unused memory nodes and define the peripheral memory regions + * required by the board dts. + * + */ + +/delete-node/ &hyp_mem; +/delete-node/ &xbl_mem; +/delete-node/ &aop_mem; +/delete-node/ &sec_apps_mem; +/delete-node/ &tz_mem; + +/* Increase the size from 2MB to 8MB */ +&rmtfs_mem { + reg = <0x0 0x94600000 0x0 0x800000>; +}; + +/ { + reserved-memory { + atf_mem: memory@80b00000 { + reg = <0x0 0x80b00000 0x0 0x100000>; + no-map; + }; + + mpss_mem: memory@86000000 { + reg = <0x0 0x86000000 0x0 0x8c00000>; + no-map; + }; + + camera_mem: memory@8ec00000 { + reg = <0x0 0x8ec00000 0x0 0x500000>; + no-map; + }; + + venus_mem: memory@8f600000 { + reg = <0 0x8f600000 0 0x500000>; + no-map; + }; + + wlan_mem: memory@94100000 { + reg = <0x0 0x94100000 0x0 0x200000>; + no-map; + }; + + mba_mem: memory@94400000 { + reg = <0x0 0x94400000 0x0 0x200000>; + no-map; + }; + + mdata_mem: mpss-metadata { + alloc-ranges = <0x0 0xa0000000 0x0 0x20000000>; + size = <0x0 0x4000>; + no-map; + }; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm6150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vreg_s1a_1p1: smps1 { + regulator-min-microvolt = <1128000>; + regulator-max-microvolt = <1128000>; + }; + + vreg_s4a_1p0: smps4 { + regulator-min-microvolt = <824000>; + regulator-max-microvolt = <1120000>; + }; + + vreg_s5a_2p0: smps5 { + regulator-min-microvolt = <1744000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_l1a_1p2: ldo1 { + regulator-min-microvolt = <1178000>; + regulator-max-microvolt = <1256000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l2a_1p0: ldo2 { + regulator-min-microvolt = <944000>; + regulator-max-microvolt = <1056000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l3a_1p0: ldo3 { + regulator-min-microvolt = <968000>; + regulator-max-microvolt = <1064000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l4a_0p8: ldo4 { + regulator-min-microvolt = <824000>; + regulator-max-microvolt = <928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l5a_2p7: ldo5 { + regulator-min-microvolt = <2496000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l6a_0p6: ldo6 { + regulator-min-microvolt = <568000>; + regulator-max-microvolt = <648000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l9a_0p6: ldo9 { + regulator-min-microvolt = <488000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l10a_1p8: ldo10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1832000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l11a_1p8: ldo11 { + regulator-min-microvolt = <1696000>; + regulator-max-microvolt = <1904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13a_1p8: ldo13 { + regulator-min-microvolt = <1696000>; + regulator-max-microvolt = <1904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l14a_1p8: ldo14 { + regulator-min-microvolt = <1728000>; + regulator-max-microvolt = <1832000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l15a_1p8: ldo15 { + regulator-min-microvolt = <1696000>; + regulator-max-microvolt = <1904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l16a_2p7: ldo16 { + regulator-min-microvolt = <2496000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l17a_3p0: ldo17 { + regulator-min-microvolt = <2920000>; + regulator-max-microvolt = <3232000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l18a_2p8: ldo18 { + regulator-min-microvolt = <2496000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l19a_2p9: ldo19 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm6150l-rpmh-regulators"; + qcom,pmic-id = "c"; + + vreg_s8c_1p3: smps8 { + regulator-min-microvolt = <1120000>; + regulator-max-microvolt = <1408000>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-min-microvolt = <1616000>; + regulator-max-microvolt = <1984000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l2c_1p3: ldo2 { + regulator-min-microvolt = <1168000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l3c_1p2: ldo3 { + regulator-min-microvolt = <1144000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l4c_1p8: ldo4 { + regulator-min-microvolt = <1648000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l5c_1p8: ldo5 { + regulator-min-microvolt = <1648000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l6c_2p9: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c_3p0: ldo7 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l9c_2p9: ldo9 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10c_3p3: ldo10 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3400000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l11c_3p3: ldo11 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3400000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dsi0 { + status = "okay"; + + vdda-supply = <&vreg_l3c_1p2>; + + panel@0 { + compatible = "visionox,rm69299-1080p-display"; + reg = <0>; + + vdda-supply = <&vreg_l8c_1p8>; + vdd3p3-supply = <&vreg_l18a_2p8>; + + pinctrl-names = "default"; + pinctrl-0 = <&disp_pins>; + + reset-gpios = <&pm6150l_gpios 3 GPIO_ACTIVE_HIGH>; + + port { + panel0_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; + + ports { + port@1 { + endpoint { + remote-endpoint = <&panel0_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; +}; + +&mdss_dsi0_phy { + status = "okay"; + vdds-supply = <&vreg_l4a_0p8>; +}; + +&qfprom { + vcc-supply = <&vreg_l11a_1p8>; +}; + +&qspi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data0>, <&qspi_data1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_mpss { + status = "okay"; + compatible = "qcom,sc7180-mss-pil"; + reg = <0 0x04080000 0 0x4040>, <0 0x04180000 0 0x48>; + reg-names = "qdsp6", "rmb"; + + clocks = <&gcc GCC_MSS_CFG_AHB_CLK>, + <&gcc GCC_MSS_Q6_MEMNOC_AXI_CLK>, + <&gcc GCC_MSS_NAV_AXI_CLK>, + <&gcc GCC_MSS_SNOC_AXI_CLK>, + <&gcc GCC_MSS_MFAB_AXIS_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "bus", "nav", "snoc_axi", "mnoc_axi", "xo"; + + iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>; + memory-region = <&mba_mem>, <&mpss_mem>, <&mdata_mem>; + + resets = <&aoss_reset AOSS_CC_MSS_RESTART>, + <&pdc_reset PDC_MODEM_SYNC_RESET>; + reset-names = "mss_restart", "pdc_reset"; + + qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>; + qcom,spare-regs = <&tcsr_regs_2 0xb3e4>; +}; + +&scm { + /* TF-A firmware maps memory cached so mark dma-coherent to match. */ + dma-coherent; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_on>; + pinctrl-1 = <&sdc1_off>; + vmmc-supply = <&vreg_l19a_2p9>; + vqmmc-supply = <&vreg_l12a_1p8>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default","sleep"; + pinctrl-0 = <&sdc2_on>; + pinctrl-1 = <&sdc2_off>; + vmmc-supply = <&vreg_l9c_2p9>; + vqmmc-supply = <&vreg_l6c_2p9>; + + cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>; +}; + +&uart3 { + status = "okay"; + + /delete-property/interrupts; + interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>, + <&tlmm 41 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default", "sleep"; + pinctrl-1 = <&qup_uart3_sleep>; + + bluetooth: bluetooth { + compatible = "qcom,wcn3990-bt"; + vddio-supply = <&vreg_l10a_1p8>; + vddxo-supply = <&vreg_l1c_1p8>; + vddrf-supply = <&vreg_l2c_1p3>; + vddch0-supply = <&vreg_l10c_3p3>; + max-speed = <3200000>; + }; +}; + +&uart8 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_hsphy { + status = "okay"; + vdd-supply = <&vreg_l4a_0p8>; + vdda-pll-supply = <&vreg_l11a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l17a_3p0>; + qcom,imp-res-offset-value = <8>; + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>; + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; + qcom,bias-ctrl-value = <0x22>; + qcom,charge-ctrl-value = <3>; + qcom,hsdisc-trim-value = <0>; +}; + +&usb_1_qmpphy { + status = "okay"; + vdda-phy-supply = <&vreg_l3c_1p2>; + vdda-pll-supply = <&vreg_l4a_0p8>; +}; + +&venus { + video-firmware { + iommus = <&apps_smmu 0x0c42 0x0>; + }; +}; + +&wifi { + status = "okay"; + vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>; + vdd-1.8-xo-supply = <&vreg_l1c_1p8>; + vdd-1.3-rfa-supply = <&vreg_l2c_1p3>; + vdd-3.3-ch0-supply = <&vreg_l10c_3p3>; + vdd-3.3-ch1-supply = <&vreg_l11c_3p3>; + wifi-firmware { + iommus = <&apps_smmu 0xc2 0x1>; + }; +}; + +/* PINCTRL - additions to nodes defined in sc7180.dtsi */ + +&pm6150l_gpios { + disp_pins: disp-state { + pinconf { + pins = "gpio3"; + function = PMIC_GPIO_FUNC_FUNC1; + qcom,drive-strength = <PMIC_GPIO_STRENGTH_MED>; + power-source = <0>; + bias-disable; + output-low; + }; + }; +}; + +&qspi_clk { + bias-disable; +}; + +&qspi_cs0 { + bias-disable; +}; + +&qspi_data0 { + bias-pull-up; +}; + +&qspi_data1 { + bias-pull-up; +}; + +&qup_i2c2_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_i2c4_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_i2c7_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_i2c9_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_uart3_cts { + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + bias-pull-down; +}; + +&qup_uart3_rts { + /* We'll drive RTS, so no pull */ + drive-strength = <2>; + bias-disable; +}; + +&qup_uart3_tx { + /* We'll drive TX, so no pull */ + drive-strength = <2>; + bias-disable; +}; + +&qup_uart3_rx { + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module is + * in tri-state (module powered off or not driving the + * signal yet). + */ + bias-pull-up; +}; + +&qup_uart8_tx { + drive-strength = <2>; + bias-disable; +}; + +&qup_uart8_rx { + drive-strength = <2>; + bias-pull-up; +}; + +&qup_spi0_spi { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi0_cs { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi6_spi { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi6_cs { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi10_spi { + drive-strength = <2>; + bias-disable; +}; + +&qup_spi10_cs { + drive-strength = <2>; + bias-disable; +}; + +&tlmm { + qup_uart3_sleep: qup-uart3-sleep-state { + cts-pins { + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + pins = "gpio38"; + function = "gpio"; + bias-pull-down; + }; + + rts-pins { + /* + * Configure pull-down on RTS. As RTS is active low + * signal, pull it low to indicate the BT SoC that it + * can wakeup the system anytime from suspend state by + * pulling RX low (by sending wakeup bytes). + */ + pins = "gpio39"; + function = "gpio"; + bias-pull-down; + }; + + tx-pins { + /* + * Configure pull-up on TX when it isn't actively driven + * to prevent BT SoC from receiving garbage during sleep. + */ + pins = "gpio40"; + function = "gpio"; + bias-pull-up; + }; + + rx-pins { + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module + * is floating which may cause spurious wakeups. + */ + pins = "gpio41"; + function = "gpio"; + bias-pull-up; + }; + }; + + sdc1_on: sdc1-on-state { + clk-pins { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd-pins { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data-pins { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <10>; + }; + + rclk-pins { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc1_off: sdc1-off-state { + clk-pins { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd-pins { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data-pins { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <2>; + }; + + rclk-pins { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc2_on: sdc2-on-state { + clk-pins { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd-pins { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + data-pins { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + sd-cd-pins { + pins = "gpio69"; + function = "gpio"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_off: sdc2-off-state { + clk-pins { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd-pins { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data-pins { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + + sd-cd-pins { + pins = "gpio69"; + function = "gpio"; + bias-pull-up; + drive-strength = <2>; + }; + }; +}; |