diff options
Diffstat (limited to 'dts/upstream/src/arm64/qcom/sm6115p-lenovo-j606f.dts')
| -rw-r--r-- | dts/upstream/src/arm64/qcom/sm6115p-lenovo-j606f.dts | 387 |
1 files changed, 387 insertions, 0 deletions
diff --git a/dts/upstream/src/arm64/qcom/sm6115p-lenovo-j606f.dts b/dts/upstream/src/arm64/qcom/sm6115p-lenovo-j606f.dts new file mode 100644 index 00000000000..54da053a804 --- /dev/null +++ b/dts/upstream/src/arm64/qcom/sm6115p-lenovo-j606f.dts @@ -0,0 +1,387 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) +/* + * Copyright (c) 2022 Linaro Limited + */ + +/dts-v1/; + +#include "sm6115.dtsi" +#include "pm6125.dtsi" + +/ { + model = "Lenovo Tab P11"; + compatible = "lenovo,j606f", "qcom,sm6115p", "qcom,sm6115"; + chassis-type = "tablet"; + + /* required for bootloader to select correct board */ + qcom,msm-id = <445 0x10000>, <420 0x10000>; + qcom,board-id = <34 3>; + + aliases { + mmc0 = &sdhc_2; + }; + + chosen { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + framebuffer0: framebuffer@5c000000 { + compatible = "simple-framebuffer"; + reg = <0 0x5c000000 0 (2000 * 1200 * 4)>; + width = <1200>; + height = <2000>; + stride = <(1200 * 4)>; + format = "a8r8g8b8"; + clocks = <&gcc GCC_DISP_HF_AXI_CLK>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&vol_up_n>; + + key-volume-up { + label = "Volume Up"; + linux,code = <KEY_VOLUMEUP>; + gpios = <&pm6125_gpios 5 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + linux,can-disable; + wakeup-source; + }; + }; + + reserved-memory { + ramoops@ffc00000 { + compatible = "ramoops"; + reg = <0x0 0xffc00000 0x0 0x100000>; + record-size = <0x1000>; + console-size = <0x40000>; + ftrace-size = <0x20000>; + ecc-size = <16>; + }; + }; +}; + +&gpu { + status = "okay"; + + zap-shader { + firmware-name = "qcom/sm6115/LENOVO/J606F/a610_zap.mbn"; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dsi0 { + vdda-supply = <&pm6125_l18>; + status = "okay"; + + panel: panel@0 { + compatible = "lenovo,j606f-boe-nt36523w", "novatek,nt36523w"; + reg = <0>; + + reset-gpios = <&tlmm 82 GPIO_ACTIVE_LOW>; + vddio-supply = <&pm6125_l9>; + + pinctrl-names = "default"; + pinctrl-0 = <&te_active &mdss_dsi_active>; + + rotation = <180>; /* Yep, it's mounted upside down! */ + + port { + panel_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; +}; + +&mdss_dsi0_out { + data-lanes = <0 1 2 3>; + remote-endpoint = <&panel_in>; +}; + +&mdss_dsi0_phy { + status = "okay"; +}; + +&pm6125_gpios { + vol_up_n: vol-up-n-state { + pins = "gpio5"; + function = "normal"; + power-source = <0>; + bias-pull-up; + input-enable; + }; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/sm6115/LENOVO/J606F/adsp.mbn"; + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/sm6115/LENOVO/J606F/cdsp.mbn"; + status = "okay"; +}; + +&remoteproc_mpss { + firmware-name = "qcom/sm6115/LENOVO/J606F/modem.mbn"; + status = "okay"; +}; + +&rpm_requests { + regulators-0 { + compatible = "qcom,rpm-pm6125-regulators"; + + pm6125_s6: s6 { + regulator-min-microvolt = <304000>; + regulator-max-microvolt = <1456000>; + }; + + pm6125_s7: s7 { + regulator-min-microvolt = <1280000>; + regulator-max-microvolt = <2080000>; + }; + + pm6125_s8: s8 { + regulator-min-microvolt = <1064000>; + regulator-max-microvolt = <1304000>; + }; + + pm6125_l1: l1 { + regulator-min-microvolt = <952000>; + regulator-max-microvolt = <1152000>; + }; + + pm6125_l4: l4 { + regulator-min-microvolt = <488000>; + regulator-max-microvolt = <1000000>; + }; + + pm6125_l5: l5 { + regulator-min-microvolt = <1648000>; + /* 3.056V capped to 2.96V for SDHCI */ + regulator-max-microvolt = <2960000>; + regulator-allow-set-load; + /* Broken hw, this one can't be turned off or SDHCI will break! */ + regulator-always-on; + }; + + pm6125_l6: l6 { + regulator-min-microvolt = <576000>; + regulator-max-microvolt = <656000>; + }; + + pm6125_l7: l7 { + /* 1.2V-1.304V fixed at 1.256V for SDHCI bias */ + regulator-min-microvolt = <1256000>; + regulator-max-microvolt = <1256000>; + /* + * TODO: SDHCI seems to also work with this one turned off, however + * there exists a possibility that it may not work with some very + * specific SDCard types, perhaps validating this against a wide + * range of models could rule that out, saving some power would + * certainly be nice.. + */ + regulator-always-on; + }; + + pm6125_l8: l8 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <728000>; + }; + + pm6125_l9: l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + }; + + pm6125_l10: l10 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <1904000>; + }; + + pm6125_l11: l11 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <1952000>; + }; + + pm6125_l12: l12 { + regulator-min-microvolt = <1624000>; + regulator-max-microvolt = <1984000>; + }; + + pm6125_l13: l13 { + regulator-min-microvolt = <1504000>; + regulator-max-microvolt = <1952000>; + }; + + pm6125_l14: l14 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <1904000>; + }; + + pm6125_l15: l15 { + regulator-min-microvolt = <2920000>; + regulator-max-microvolt = <3232000>; + }; + + pm6125_l16: l16 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <1904000>; + }; + + pm6125_l17: l17 { + regulator-min-microvolt = <1152000>; + regulator-max-microvolt = <1384000>; + }; + + pm6125_l18: l18 { + /* 1.104V-1.312V fixed @ 1.232V for DSIPHY */ + regulator-min-microvolt = <1232000>; + regulator-max-microvolt = <1232000>; + }; + + pm6125_l19: l19 { + regulator-min-microvolt = <1624000>; + regulator-max-microvolt = <3304000>; + }; + + pm6125_l20: l20 { + regulator-min-microvolt = <1624000>; + regulator-max-microvolt = <3304000>; + }; + + pm6125_l21: l21 { + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3600000>; + }; + + pm6125_l22: l22 { + regulator-min-microvolt = <2952000>; + /* 3.304V capped to 2.96V for SDHCI */ + regulator-max-microvolt = <2960000>; + regulator-allow-set-load; + /* Broken hw, this one can't be turned off or SDHCI will break! */ + regulator-always-on; + }; + + pm6125_l23: l23 { + regulator-min-microvolt = <3200000>; + regulator-max-microvolt = <3400000>; + }; + + pm6125_l24: l24 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <3600000>; + }; + }; +}; + +&sdhc_2 { + cd-gpios = <&tlmm 88 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_state_on &sdc2_gate_pin>; + pinctrl-1 = <&sdc2_state_off>; + vmmc-supply = <&pm6125_l22>; + vqmmc-supply = <&pm6125_l5>; + no-sdio; + no-mmc; + status = "okay"; +}; + +&sleep_clk { + clock-frequency = <32764>; +}; + +&tlmm { + gpio-reserved-ranges = <14 4>; + + /* + * This is a wholly undocumented pin (other than a single vague "pwr-gpios" reference) + * that needs to be toggled for the SD Card slot to work properly.. + */ + sdc2_gate_pin: sdc2-gate-state { + pins = "gpio45"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + output-high; + }; + + te_active: te-active-state { + pins = "gpio81"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-pull-down; + }; + + mdss_dsi_active: dsi-active-state { + pins = "gpio82"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; +}; + +&ufs_mem_hc { + vcc-supply = <&pm6125_l24>; + vcc-max-microamp = <600000>; + vccq2-supply = <&pm6125_l11>; + vccq2-max-microamp = <600000>; + vdd-hba-supply = <&pm6125_l18>; + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&pm6125_l4>; + vdda-pll-supply = <&pm6125_l12>; + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb_dwc3 { + maximum-speed = "high-speed"; + dr_mode = "peripheral"; + + phys = <&usb_hsphy>; + phy-names = "usb2-phy"; +}; + +&usb_hsphy { + vdd-supply = <&pm6125_l4>; + vdda-pll-supply = <&pm6125_l12>; + vdda-phy-dpdm-supply = <&pm6125_l15>; + status = "okay"; +}; + +&wifi { + vdd-0.8-cx-mx-supply = <&pm6125_l8>; + vdd-1.8-xo-supply = <&pm6125_l16>; + vdd-1.3-rfa-supply = <&pm6125_l17>; + vdd-3.3-ch0-supply = <&pm6125_l23>; + qcom,ath10k-calibration-variant = "Lenovo_P11"; + status = "okay"; +}; + +&xo_board { + clock-frequency = <19200000>; +}; |